Manuale d’uso / di manutenzione del prodotto 2824 del fabbricante Elo TouchSystems
Vai alla pagina of 28
User’s Manual No. 980346-001 Rev. A ©2001 Zebra Technologies Corporation 2824 Thermal Printer User’s Manual.
ii 980346-001 Rev. A.
FOREWORD This manual provides installation and operation information for the LP 2824 series printers, manu - factured by Zebra Technologies Corporation, Camarillo, California. COPYRIGHT NOTICE This document contains information proprietary to Zebra Technologies Corporation.
SHOCK HAZARD WARNING: The printer and power supply should never be operated in a location where either one can get wet. Personal injury could result. MEDIA WARNING: Always use high quality approved labels, tags and transfer ribbons.
980346-001 Rev. A v TABLE OF CONTENTS Installation and Operation . . . . . . . . . . . . . . . . . 1 Unpacking Your Printer . . . . . . . . . . . . . . . . . . . . 2 Getting To Know Your Printer . . . . . . . . . . . . . . . . . 3 Installation . . . .
vi 980346-001 Rev. A.
1 Installation and Operation This section provides information on the installation and operation of the printer. The printer is a low cost, desktop direct thermal printer. The printer is specifically designed for printing labels, tags or continuous receipts (with or without bar codes) from any DOS™, Win- dows™or ASCII-based compatible host.
Unpacking Your Printer 2 980346-001 Rev. A Installation and Operation.
Getting To Know Your Printer 980346-001 Rev. A 3 Installation and Operation.
Installation The following steps will guide you through the installation of the printer and software. Step ➊ Attach Power Supply To The Printer See the SHOCK HAZARD WARNING on page iv.
Step ➋ Attach Interface Cable The printer has either a parallel interface or a serial interface (with optional RJ-11 connector). For additional information on serial cable wir - ing, refer to Appendix A.
Step ➌ Load Labels 6 980346-001 Rev. A Installation and Operation MO VIE Open Cover Power ON Adjust Holders 1.0 inch 2.5 cm 1.5 inch 3.8 cm MO VIE.
Load Labels - continued 980346-001 Rev. A 7 Installation and Operation Install Roll Remove Outside Length For more infor - mation refer to appendix A MO VIE.
Load Labels - continued If the indicator remains dark, see Appendix A - Troubleshooting. 8 980346-001 Rev. A Installation and Operation Close Cover Tap Feed Button Thread Through Guides.
Step AutoSense Gap Sensor Adjustment Perform this procedure when loading a new roll. If your printer has the label dispenser option, turn OFF the label taken sensor.
AutoSense Gap Sensor Adjustment - continued If the indicator remains orange or red, see the troubleshooting steps. 10 980346-001 Rev. A Installation and Operation 4 MO3351F 16 V3.
Label Dispenser Option 980346-001 Rev. A 11 Installation and Operation Open Door Use a Stylus to Switch On the Label Taken Sensor Remove Several Labels Push Liner Through Slot Close Door MO VIE.
Using Fan-Fold Media 12 980346-001 Rev. A Installation and Operation Open Guides to Width of Media Lock Guides in Place Thread Media Through Guides Insert Media.
Step ➎ Install Software Start your computer and follow the installation instructions on the compact disc (CD). 980346-001 Rev. A 13 Installation and Operation.
14 980346-001 Rev. A Installation and Operation.
Appendix A - Troubleshooting Problem Solution or Reason STATUS Indicator Does not light when power switch is turned to ON (I) position. 1. Check power connections from A.C. outlet to power supply to printer. Lights GREEN, but printer will not print. 1.
Problem Solution or Reason Prints only partial label or skips a label. 1. Perform AutoSense gap sensor adjustment on page 8. 2. Label caught on print head. 3. Print head is not properly latched. 4. Possible software problem. Check the printer memory configuration.
Serial Interface Cable Wiring The figure below displays the cable wiring required to use the printer's RS-232 serial interface. 980346-001 Rev. A 17 Appendix A - Troubleshooting N/C RxD TxD DTR G.
18 980346-001 Rev. A Cash Drawer Cable Wiring The figure below displays the pin assignments for the printer's retail cash drawer interface. Re - fer to the cash draw manufacturer's documenta - tion for proper drawer wiring. *+24 volts D.C. at no greater than 1.
980346-001 Rev. A 19 Parallel Interface Cable Wiring The figure below displays the cable wiring required to use the printer's Centronics parallel interface. +5 volts at 300 mA for external device (e.g. KDU or scanner) Appendix A - Troubleshooting PRINTER DB - 25 Pi n No .
20 980346-001 Rev. A Cleaning the Print Head When you load new media, you can also clean the print head. Appendix A - Troubleshooting Rub Cleaning Pen Across Dark Area of Print Head Wait One Minute Be.
980346-001 Rev. A 21 Preparing Media, Paper, and Labels Before Loading During shipment, the outside length of media may become dirty when handled or dusty when stored. A preparation before loading media makes sure both the print head and platen stay cleaner for more time.
980346 - 001A.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Elo TouchSystems 2824 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Elo TouchSystems 2824 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Elo TouchSystems 2824 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Elo TouchSystems 2824 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Elo TouchSystems 2824, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Elo TouchSystems 2824.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Elo TouchSystems 2824. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Elo TouchSystems 2824 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
