Manuale d’uso / di manutenzione del prodotto 95604 G del fabbricante Electrolux
Vai alla pagina of 26
AUS ERFAHRUNG GUT 95600 G - 9560 1 G - 9560 2 G 95604 G Gas hob Table de cuisson Kochmulde Gaskookplaat Piano di cottura Operating and Installation Instructions GB Notice d’utilisation et d’encast.
2 Important Safety Information You MUST r ead these warnings car efully before installing or us ing the hob. If you need assi stance, contact our Customer Care Department on 087 05 350 350 Installation ● This hob must be installed by qualified personnel, accor ding to the manufacturer’ s instructions and to the relevant British Standar ds.
3 ● When in use a gas cooking hob will produce heat and moisture in the room in which it has been installed. Ensure there is a continuous air supply , keeping air vents in good condition or installing a cooker hood with a venting hose.
4 Content s Important Safety Information .................................................................... 2 In structions for the User .............................................................................. 6 Description of the Hob ........
5 This appliance is manufactured accor ding to the following EEC dir ectives: 73/23 EEC - 90/683 EEC - 93/68 EEC - 89/336 EEC - 90/396 EEC, current edition.
6 1. Hob T op 2. Rapid Burner 3. Semi-r apid Burners 4. Auxiliary Burner 5. Contr ol knob for back right burner (semi-rapid) 6. Contr ol knob for back left burner (semi-rapid) 7.
7 HOB BURNERS To light a burner , turn the relevant contr ol knob anticlockwise to the maximum position, then push it down to ignite the burner . Upon, ignition, keep the knob pushed down about 5 seconds, then adjust the flame as required. If the burner does not ignite, turn the control knob to zer o, and try again.
8 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob fr om the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
9 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local AEG Service Force Centr e.
10 Service and Spar e Part s When you contact the Service Force Centr e, they will need the following information: 1. Y our name, address and post code. 2. Y our telephone number 3. Clear and concise details of the fault 4. The model and the serial number (see r ating label on the back of this instruction booklet) 5.
11 Guarantee Condition s AEG offer the following guar antee to the first purchaser of this appliance. 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the fir st retail purchaser , which must be verified by pur chase invoice or similar documentation.
12 OVERALL DIMENSIONS Width: 580 mm. Depth: 51 0 mm. Height: 88 mm. Weight: 8 Kg. CUT OUT DIMENSIONS Width: 550 mm. Depth: 470 mm. Thickness: 30 mm. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V 50Hz supply , 3 core flexible cable with non r ewireable plug fitted with a 3 amp cartridge fuse.
13 BURNER RAPID SEMI-RAPID AUXILIARY (large) (medium) (small) POSITION MAX MIN MAX MIN MAX MIN NOMINAL THERMAL POWER kW 2.9 0.65 1.9 0.45 1.0 0.33 NOMINAL FLOW RATE m 3 /h 0.276 0.062 0.181 0.043 0.095 0.031 NOZZLE REFERENCE 119 Adjust. 96 Adjust. 70 Adjust.
14 Important safety r equir ement s This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations ar e contained in the following British Standards Codes Of Pr actice: B.
15 650 mm 400 mm 400 mm 100 mm 50 mm 50 mm 55 mm 600 mm 700 mm 400 mm 100 mm 400 mm 50 mm 55 mm 50 mm CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN .
16 A) End of shaft with nut B) Washer C) Elbow FO 0814 FO 0264 this book be ignored. On the end of the shaft, which includes the GJ 1/2" threaded elbow , adjustment is fixed so that the washer is fitted between the components as shown in the diagram.
17 550 470 580 510 55 min. FO 2359 Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or dr awer If the hob is to be installed above a cupboar d or drawer it will be necessary to fit a heat resistant boar d below the base of the hob on the under side of the work surface.
18 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 1 2 Building over a kitchen unit with door Proper arr angements must be taken in designing the furnitur e unit, in or der to avoid any contact with the bottom of the hob which can be heated when it is operated.
19 Fitting the hob to the worktop Befor e fitting the hob into the cut out, an adhesive seal must be fitted to the underside outside edge of the hob. It is essential that no gaps are left in this seal in order to pr event spillage near the hob seeping into the cabinet below .
20 Electrical connection s Any electrical work requir ed to install this hob should be carried out by a qualified electrician or competent person, in accor dance with the current r egulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measur es not be observed.
21 P ermanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the requir ed load in compliance with the current electric r egulations.
22 Fault Finding Preliminary Electrical Sy stem s Check START Isolate appliance and carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supply should now be satisfactory. Carry out: D: Resistance to Earth check.
23 A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and all contacts are clean and tight.
24 Check gas supply at burner Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ig.
25 Commi ssioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the pr ocedure below . 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.
26 Conver sion from Natur al Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injector s are fitted and the gas r ate is adjusted to suit.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Electrolux 95604 G è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Electrolux 95604 G - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Electrolux 95604 G imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Electrolux 95604 G ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Electrolux 95604 G, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Electrolux 95604 G.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Electrolux 95604 G. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Electrolux 95604 G insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
