Manuale d’uso / di manutenzione del prodotto CH3083 del fabbricante Eclipse - Fujitsu Ten
Vai alla pagina of 95
OWNER'S MANUAL We appreciate y our purchase of this receiver . Please read through this manual f or correct operation. We suggest that after reading it y ou keep this manual in a safe place f or future ref erence. CD5415 ESN E5 High-P ow er CD Receiver with MP3 Decoder www.
For your safety in using the CD5415 Warnings and caution signs, illustrated below, are posted throughout this manual as well as on the CD5415. They show safe and correct ways to handle the product so as to prevent personal injury to you, others and to avoid property damage.
3 • When installing equipment do not remove or alter existing vehicle fasteners, including nuts, bolts, screws, clips, and fittings. Never detach, move or alter existing vehicle wiring, including electrical grounds and straps. Alteration of existing vehicle components may make vehicle unsafe to operate.
4 • Do not disassemble or alter this equipment. Accidents, fires or shocks may result. • Do not let water or foreign objects enter the internal parts of this equipment. Smoke, fires or shocks may result. • Pay attention to where the remote control is left.
5 • Avoid installing in places where it cannot be fastened securely or where there are strong vibrations. Also, if you installed the unit with double-sided tape, first wipe away dirt and wax from the installation area.
6 • Do not use batteries other than those specified. Also, do not mix old and new batteries. Injuries or pollution to the surroundings may result from battery ruptures and leakage. • When inserting batteries into the equipment, be careful of the polarity (positive/negative), and insert them as indicated.
7 T able of Contents Operating precautions ............................................ 11 Notes on operation ..................................................................... 11 About compact discs ................................................
8 How to operate the CD player ................................. 33 Listening to CDs ......................................................................... 33 Advancing to the next track or returning to the beginning of the track being played .....
9 Changing the radio band location ............................................... 51 FM reception characteristics ...................................................... 52 FM reception differs from AM ............................................... 52 Fading out .
10 Switching the display .................................................................. 65 How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only) .............. 66 About HD Radio ..........................................
11 Operating precautions <Your CD5415 will perform well over a long period of time through correct handling and care.> • For your safety, play only at volume levels that allow outside sounds to be heard. • We recommend using with this player a disc with the logo shown to the left.
12 Operating precautions • The signal recorded on a compact disc is read by a laser beam, so nothing touches the disc surface. A scratch on the recorded surface or a badly warped disc may cause deteriorated sound quality or intermittent playback.
13 Operating precautions About CD accessories • Do not use accessories (stabilizers, protective seals, laser lens cleaners, etc.) sold for “ improving sound performance ” or “ protecting CDs. ” The changes in CD thickness or outside dimensions made by these accessories may cause problems in the player.
14 Operating precautions About borrowed CDs • Do not use a CD with glue or remnants of adhesive tape or labels. They may cause the CD to get stuck inside or damage the deck. How to remove CDs • When removing the ejected disc, pull it straight out along the slot.
15 Names of controls and parts Names of controls and parts Ejects compact disc. Switches between disc modes. Switches to radio mode and switches radio bands. Inserts compact discs. Switches screen display and turns function mode ON/OFF. Sets the equalizer settings.
16 ESN security operating procedure ESN security operating procedure About ESN This deck incorporates ESN (ECLIPSE Security Network). The ESN is a security system which disables all deck functions when the power is restored if the deck is stolen from the vehicle.
17 ESN security operating procedure ATTENTION • If there is a problem with the inserted CD, an [ERR] message will appear for two seconds and the CD will be ejected. Reinsert the ejected CD. • If a CD causes the [ERR] message to appear twice in a row, a [CHANGE] message will appear for two seconds.
18 ESN security operating procedure ATTENTION • This process cancels the protection for the ESN deck. • If power to the ESN deck is disconnected, then reconnected, a Key CD will not need to be inserted in order to return the unit to normal operation.
19 ESN security operating procedure ATTENTION • If an incorrect CD is inserted, an [ERR_] ("ERR" and error number) message will appear for two seconds, after which the CD will be ejected. • If [ERR5] (the 5th time an error has occurred) appears, [HELP] will appear, after which the CD will be ejected.
20 ESN security operating procedure ATTENTION • If an incorrect CD is inserted, an [ERR_] ("ERR" and error number) message will appear for two seconds, after which the CD will be ejected. • This process cancels the protection for the ESN deck.
21 ESN security operating procedure How to turn the security indicator on/off With the unit in standby, press button [2], then the [DISP FUNC] button and hold both for more than one second. 1 [IND. FLASH] or [IND. -----] appears on the display. 2 [IND.
22 Basic operation Turning the power on and off. When the power is turned on, the state used when the power was turned off such as CD and tuner playback is restored. When the vehicle has no ACC position on the ignition switch, care is needed when turning off the deck.
23 Basic operation Listening to a CD Insert a CD into the disc slot, label side up. 1 The CD will start playing. ATTENTION When a CD is already loaded, press the [DISC] button to switch to the CD mode.
24 Basic operation Listening to the tuner Press the [FM AM] button. 1 This will turn the tuner on. Press the [FM AM] button to switch to the desired FM or AM bands. 2 Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in order each time the button is pressed.
25 Basic operation Warning Adjusting audio volume Turn the [AUDIO CONTROL] button to the left or right. 1 Turn to the right: Increases the volume. Turn to the left: Decreases the volume. Do not adjust the volume or other controls while driving the vehicle.
26 Basic operation Various audio control modes may be fine-tuned using this procedure. Modes will switch in the order shown below each time the button is pressed. Switching audio control modes Press the [AUDIO CONTROL] button for less than one second to select the item to be adjusted.
27 Basic operation Adjusts left/right speaker balance. Turn the [AUDIO CONTROL] button to the left or right. Turn to the right: Emphasizes right speakers. Turn to the left: Emphasizes left speakers. Adjusts front/rear speaker balance. Turn the [AUDIO CONTROL] button to the left or right.
28 Basic operation The merging of sound between the front and rear speakers and the woofer can be improved by selecting the phase. Switch the phase to a phase which lets the speakers combine without any disharmony. Turn the [AUDIO CONTROL] button to select NORMAL or REVERSE.
29 Basic operation The adjustment values for BASS, MIDDLE and TREBLE settings made in the audio control mode can be stored. The stored adjustment values can be called by changing the equalizer mode. For detail, see “ Changing the equalizer mode ” on page 30.
30 Basic operation [SOUND] button EQ (equalizer) mode can be used to adjust the frequency of the audio channels being played back in accordance with the genre and instruments of the music being played.
31 Basic operation A variety of settings can be changed. The function mode is activated. Setting items will be displayed in the following order when the [SEL] button is turned to the right. Making changes with Function Mode Press the [DISP FUNC] button for more than one second.
32 Basic operation This receiver uses the 12-hour display notation. Setting the time [RTN] button [SEL] button Turn the [SEL] button to select CLOCK. 1 Press the [SEL] button. 2 Turn the [SEL] button to the left or right. 4 Turn to the right: Turns the time forward.
33 How to operate the CD player Listening to CDs Press the [DISC] button. 1 First press the [DISC] button to switch to the disc mode. It is assumed here that a CD has already been loaded into the unit.
34 How to operate the CD player Advancing to the next track or returning to the beginning of the track being played Turn the [SEL] button to the left or right. 1 Turn to the right: Advances to the next track. Turn to the left: Returns to the beginning of the track being played.
35 How to operate the CD player Repeating the same track (REPEA T) Press button [5] to repeat the track being played. 1 To cancel, press button [5] again. Playing tracks in random order (RANDOM) Press button [6] to play the tracks in random order. 1 To cancel, press button [6] again.
36 How to operate the CD player Ejecting the disc Press the [CD (EJECT)] button. 1 Disc is ejected. Displaying CD TEXT Press the [DISP FUNC] button for less than one second.
37 How to operate the MP3 player About MP3 How to operate the MP3 player MP3 (MPEG Audio Layer III) is a standard format for audio compression technology. By using MP3, a file can be compressed to one-tenth the size of the original. This deck has limitations on MP3 file standards and recorded media and formats that can be used.
38 How to operate the MP3 player Media capable of playing MP3 includes CD-R and CD-RW discs. Compared to CD-ROM media commonly used for music discs, CD-R discs are fragile in high temperature/high humidity environments and one section of the CD-R may become incapable of playback.
39 How to operate the MP3 player Caution Only files with the MP3 file extension ".mp3" can be recognized as MP3 and played. Be sure to save MP3 files with the ".mp3" file extension. The "MP" letters of the file extension will be recognized whether entered as uppercase letters or lowercase letters.
40 How to operate the MP3 player Listening to MP3 file Press the [DISC] button. 1 This starts MP3 file play. If an external CD changer is connected, each additional press of the [DISC] button will switch modes from CD changer 1 ➔ CD changer 2 ➔ CD player.
41 How to operate the MP3 player Skipping to the next or previous folder Press button [1] or [2]. 1 Button [1]: Selects the next lower folder. Button [2]: Selects the next folder. Fast forward or rewind the song currently being played. [ ] button: Fast forward.
42 How to operate the MP3 player In the root directory, when a file cannot replay, the system will return to the first file that can perform a replay. (In the configuration example, the file is returning to 001.mp3. See page 38.) Return to the root directory of the CD Press the [RTN] button.
43 How to operate the MP3 player Press the button briefly to play just the first 10 seconds of each song for all the files in the current folder being played. Pressing the button until [ALL SCAN] is displayed will play just the first 10 seconds of the first song in each folder.
44 How to operate the MP3 player Press the button briefly to randomly play the files in the current folder being played. Pressing the button until [ALL RANDOM] is displayed will randomly play the files in all the folders. To cancel, press button [6] again.
45 How to operate the MP3 player Each time the button is pressed the following will be displayed in order. Folder Name/File Name* 1 ➔ Tag* 2 ➔ Folder Number/File Number ➔ Clock ➔ Elapsed Time * 1 : The display area shows a maximum of 8 characters and then scrolls to display the remaining characters.
46 How to operate the tuner T uning to a station Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in order each time the button is pressed. First, press the [FM AM] button to start tuner operation. There are automatic and manual methods for setting stations in memory.
47 How to operate the tuner Press the [SEL] button for more than two seconds until a beep is heard. 2 The automatic preset mode starts. The [ASM ON] indicator on the screen flashes, and stations are automatically entered in memory under buttons [1] to [6].
48 How to operate the tuner Manually setting stations into memory Press the [FM AM] button for less than one second to switch between FM and AM. 1 Turn the [SEL] button to the right or left to tune to the station to be entered in memory. 2 This section covers the setting of stations in memory under the numbered buttons.
49 How to operate the tuner Preset station scan Press the [SEL] button for less than one second. 1 [P SCAN] will appear on the display, and stations stored under preset buttons [1] through [6] will be played for five seconds each. To stop the preset scan mode at a desired station, press the [SEL] button again.
50 How to operate the tuner [FM AM] button Changing the reception sensitivity for automatic scanning Check that the deck is in standby mode. 1 Press and hold the [FM AM] button, then button [1], and hold both for more than three seconds. 2 The mode switches between AUTO mode and DX mode each time the buttons are pressed.
51 How to operate the tuner Check that the deck is in standby mode. 1 Press and hold the [FM AM] button, then button [3], and hold both for more than three seconds.
52 How to operate the tuner FM reception characteristics A characteristic of transmitted signals is that lower frequencies travel further. FM frequencies are much higher than AM ’ s (similar to a ray of light): they won ’ t bend but they will reflect.
53 How to operate the tuner A home receiver can catch weak FM stereo signals through the use of a tall, directional or ultra-sensitive antenna. In a moving vehicle, the area for good reception is limi.
54 How to use an optional remote control Cleaning the remote control Precautions in use of the remote control • Be careful when handling the remote control, especially because it is small and light. Dropping or striking it hard may damage it, wear out the battery or cause a malfunction.
55 How to use an optional remote control T urning the power on/off Press the [PWR] button. 1 The power turns on or off each time the button is pressed. When the power is turned on, the state used when the power was turned off such as CD and tuner playing is restored.
56 How to use an optional remote control [MODE] button [TU] button [BAND] button Switching playback modes Press the [MODE] button. 1 Press the button to switch modes in the following sequence: Tuner Disc How to play the tuner Selecting the FM/AM band Each press will switch tuner modes from FM1 ➔ FM2 ➔ FM3 ➔ AM.
57 How to use an optional remote control [DISC] button [ PRESET CH ] buttons [BAND] button [ TUNE ・ SEEK ] buttons Selecting a station (manually or automatically) A short tap of the button will allow manual station tuning. Pressing for more than one second will start automatic tuning.
58 How to use an optional remote control [ TRACK ] buttons [ ] button: Skips to the next track. [ ] button: Returns to the beginning of the track being played. (Press repeatedly to move to previous tracks.) ATTENTION Hold the [ ] button down to fast forward, or the [ ] button to rewind through the track being played.
59 How to use an optional remote control Listening to MP3 file Press the [DISC] button. 1 The disc mode changes and the disc starts playing. Each press will switch the modes from CD player ➔ CD changer 1 ➔ CD changer 2. Any device that has no CD loaded or that is not connected is skipped.
60 How to use an optional remote control Advancing to the next file or returning to the beginning of the file being played Advancing to the next file or returning to the beginning of the file being played. Skipping to the next or previous folder Skipping to the next folder or returning the previous folder.
61 How to use an optional remote control Replacing the battery Remove the back cover of the remote control unit by gently pressing and sliding it in the direction indicated by the arrow. 1 Use two AAA-size batteries. Install the two batteries provided into the compartment as illustrated inside the compartment.
62 How to operate the receiver with an optional CD changer connected How to operate the receiver with an optional CD changer connected Listening to a CD Fast Forward/Rewind Advancing to the next track.
63 How to operate the receiver with an optional CD changer connected Playing the beginning of tracks (SCAN) Press button [4]. Pressing the button causes the changer to move up to the next track and play it for 10 seconds, then move up to the next track and play it for 10 seconds, and so on, on one CD, until the button is tapped again.
64 How to operate the receiver with an optional CD changer connected Skipping to the next or previous CD Press button [1] or [2]. Button [1]: Selects the next lower number disc. Button [2]: Selects the next higher number disc. 1 Playing tracks in random order (RANDOM) Press button [6].
65 How to operate the receiver with an optional CD changer connected Switching the display Press the [DISP FUNC] button for less than one second. Each time the button is pressed the following will be displayed in order. track No./elapsed time ➔ disc No.
66 How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only) About HD Radio If the optional HD Radio (High Definition Radio) tuner unit is connected, terrestrial digital broadcasts can be received.
67 How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only) [SEL] button [FM AM] button [ ] button [ ] button First, press the [FM AM] button to start tuner operation. There are automatic and manual methods for setting stations in memory.
68 How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only) Press the [FM AM] button for less than one second to switch to the desired FM or AM bands. Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in order each time the button is pressed.
69 How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only) Press the [FM AM] button for less than one second to switch between FM and AM. 1 Turn the [SEL] button to the right or left to tune to the station to be entered in memory.
70 How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only) Press the [SEL] button for less than two seconds. 1 [P SCAN] will appear at the display, and stations stored under preset buttons [1] through [6] will be played for five seconds each.
71 How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only) Press the [DISP FUNC] button for less than one second. 1 Each time the button is pressed, the display item changes in the following order: station name ➔ title* ➔ artist* ➔ album* ➔ genre.
72 How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only) Press the [RTN] button. 6 At this time, other adjustments can also be made in Function Mode. Press the [DISP FUNC] or [RTN] to exit Function Mode. 7 Press the [SEL] button.
73 How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only) How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only) About SIRIUS satellite radio If the optional SIRIUS satellite radio tuner unit is connected, satellite radio can be received.
74 How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only) Press the [FM AM] button for more than two seconds. 1 The mode switches between satellite radio mode and FM/AM radio mode each time the button is pressed.
75 How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only) Press the [ ] or [ ] button for more than one second. 1 [ ] button: Advance to next category. [ ] button: Return to previous category. Category selection Press the [SEL] button for more than two seconds.
76 How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only) Turn the [SEL] button to the right or left to tune to the channel to be entered in memory. 1 Manually setting channels into memory This section covers the setting of channels in memory under the numbered buttons.
77 How to operate the tuner with an optional SIRIUS satellite radio tuner connected (U.S.A. only) Preset channel scan This function enables reception of all the channels in the preset buttons for five seconds each. [SEL] button Buttons [ 1 ] to [ 6 ] [DISP FUNC] button Press the [SEL] button for less than two seconds.
78 If you have a question: First check the items mentioned below before attempting to troubleshoot problems. If a problem occurs, for instance when the unit does not respond to any button presses, or the display doesn't work correctly, press the [RESET] button using a paper clip or similar item.
79 If you have a question: Displayed information (for troubleshooting) The information listed in the chart below is displayed to show the status of the CD, CD changer and SIRIUS tuner.
80 If you have a question: Problem Mode Causes Remedial action to take Refer to page Common to all Dead or weak sound Power does not turn on. Frequencies or titles set in memory are deleted. No guide tone sounds. The remote control does not work. Is MUTE functioning? Cancel MUTE.
81 If you have a question: Problem Mode Causes Remedial action to take Refer to page The disc cannot be inserted. The disc is ejected as soon as it is inserted.
82 Specifications < GENERAL > Power Supply 14.4V DC (11-16V) Current Drain 3A Dimensions (W x H x D) In-Dash Unit 7" x 2" x 6-1/8" (178 x 50 x 155mm) Mass (weight) Approx.
83 Before installation No. Item Q'ty 1 Main unit 1 2 Mounting sleeve 1 3 Side bracket 2 4 Rear bracket 1 5 Bezel 1 6 Bushing 1 7 Self-tapping screw (6 x 16 mm) 1 8 Stud bolt 1 9 Flat head screw (.
84 Mounting instruction Mounting the main unit Insert the mounting sleeve into the opening in the vehicle dash board or console box. 1 Use a screwdriver or the like to bend the tabs in the mounting sleeve to secure the mounting sleeve. 2 Attach the side brackets to the main unit using flathead screws.
85 Mounting instruction Mount the stud bolt to the main unit. 4 Insert the main unit into the mounting sleeve until it locks in place. 5 Fasten the rear of the main unit using either method [A] or [B].
86 Mounting instruction Remove the pocket and any other accessories from the center cluster to make room for the main unit. 1 Remove the mounting side brackets for the pocket. 2 Attach the side brackets to the main unit. 3 Install the main unit in the vehicle.
87 Mounting instruction Names of lead wires and destinations (refer to Page 89) No. Name Wire color Destination 1 ACC Red Connect where the power comes on when the ignition is in the ACC position. 2 B+ Yellow Connect where the power is constantly available, regardless of the ignition switch's position.
88 Mounting instruction System CD5415 CD5415 CH3083 CH3083 CD5415 HDR105 CH3083 CD5415 CH3083 HD RADIO TUNER.
89 Mounting instruction 7 5415 FL FR RL RR (+) (–) (+) (–) (+) (–) (+) (–) 1) CD5415 Receiver , used alone Caution Never connect the power supply to the speaker leads, otherwise it cause damage to the main unit.
90 Mounting instruction CD5415 CH3083 (+) ( – ) (+) (+) (+) ( – ) ( – ) ( – ) 2) CD5415 + CH3083 + Power Amplifier Caution Never connect the power supply to the speaker leads, otherwise it cause damage to the main unit.
91 Mounting instruction CD5415 CH3083 CH3083 (+) ( – ) (+) ( – ) (+) ( – ) (+) ( – ) 3) CD5415 + CH3083 + CH3083 + Power Amplifier Caution Never connect the power supply to the speaker leads, otherwise it cause damage to the main unit. Note 1.
92 Mounting instruction CD5415 CH3083 (+) ( – ) (+) (+) (+) ( – ) ( – ) ( – ) HDR105 4) CD5415 + HDR105 + CH3083 + Power Amplifier Caution Never connect the power supply to the speaker leads, otherwise it cause damage to the main unit.
93 How to contact customer service Should the product require service, please contact your nearest following Eclipse dealer. < U.S.A/CANADA > DIVISION OF FUJITSU TEN CORP. OF AMERICA 19600 SOUTH VERMONT AVENUE, TORRANCE, CA 90502 Phone: (310) 327-2151 < AUSTRALIA > FUJITSU TEN (AUSTRALIA) PTY LTD.
94 How to contact customer service < KOREA > Transpectra Co., Ltd. 115-16 nonhyun dong kangnam ku Seoul, Korea. Phone: 02-540-4595 Fax: 02-2-540-4666 HYUNDAI AUTONET Co., LTD. 1st FL. Namhyoung Bldg, 746-23 Yeoksam-Dong, Kangnam-Ku, Seoul, Korea 135-080 Phone: 02-508-6001 Fax: 02-2-508-6067 < TAIWAN > Sentrek Taiwan, LTD.
IMPOR T ANT RECORD YOUR “KEY CD” HERE… ST ORE YOUR “KEY CD” ALONG WITH YOUR OWNER’S MANUAL T AKE THIS OUT . 95.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Eclipse - Fujitsu Ten CH3083 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Eclipse - Fujitsu Ten CH3083 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Eclipse - Fujitsu Ten CH3083 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Eclipse - Fujitsu Ten CH3083 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Eclipse - Fujitsu Ten CH3083, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Eclipse - Fujitsu Ten CH3083.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Eclipse - Fujitsu Ten CH3083. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Eclipse - Fujitsu Ten CH3083 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
