Manuale d’uso / di manutenzione del prodotto SHC-210 del fabbricante Echo
Vai alla pagina of 24
H EDGE C LIPPER O PERA T OR ' S M ANUAL 1 Shaft Hedge Clipper Operator's Manual MODEL SHC-210 Serial Number 07001001 - 07999999 X750005481 03/03 X7502253801 W ARNING DANGER Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety Manual.
2 I NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operating tips and SAFETY messages.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 3 S AFETY DECALS Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer.
4 INTERNA TIONAL SYMBOLS Symbol description/application Symbol form/shape Symbol description/application Symbol form/shape Hot Surface Carburetor adjustment - Idle speed Carburetor adjustment - High s.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 5 EXTENDED OPERA TION / EXTREME CONDITIONS Vibration and Cold It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals, may be brought about by exposure to vibration and cold.
6 SAFE OPERA TION W ARNING DANGER Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. Read the Manual • Provide all users of this equipment with the Operator's Manual and Safety Manual for instructions on Safe Operation.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 7 D ESCRIPTION The ECHO product you have purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, some assembly of SHC-210 is required. After opening the carton, check for damage.
8 1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter. 2. GRIP, RIGHT HAND REAR - Cushioned grip for right hand. 3. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 9 S PECIFICA TIONS MODEL ----------------------------------------------------- SHC-210 Length ------------------------------------------------------- 1790 mm (70.5 in.) Width -------------------------------------------------------- 250 mm (9.
10 A SSEMBL Y Tools Required: 4 mm hex wrench, screwdriver Parts Required: Power Head/Drive Shaft Assembly and Gear Housing Assembly GEAR HOUSING ASSEMBL Y / DRIVE SHAFT W ARNING DANGER Hedge Clipper Blades are very sharp. Wear gloves to protect hands.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 11 P RE -O PERA TION FUEL Fuel Requirements Gasoline - Use 89 Octane [R + M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to 15% MTBE (methyl tertiary-butyl ether). Gasohol containing methyl (wood) alcohol is NOT approved.
12 O PERA TION ST ARTING COLD ENGINE W ARNING DANGER The attachment will operate immediately when the engine starts and could result in loss of control and possible serious injury. Keep movable parts of the attachment off the ground and away from objects that could become entangled or thrown.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 13 ST ARTING W ARM ENGINE The starting procedure is the same as Cold Start except DO NOT close the choke, and do not depress throttle trigger to wide open position. W ARNING DANGER The attachment should not move at idle, otherwise serious personal injury may result.
14 M AINTENANCE Your ECHO product is designed to provide many hours of trouble free service. Regular scheduled maintenance will help achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 15 AIR FIL TER Level 1. Tools required: 25 or 50 mm (1 or 2 in.) cleaning brush Parts required: 90008 REPOWER TM Air & Fuel Filter Kit 1 . Close choke (Cold Start Position [ ] ). This prevents dirt from entering the carburetor throat when the air filter is removed.
16 SP ARK PLUG Level 2. Tools Required: T-Wrench, feeler gauge, soft metal brush Parts Required: Spark Plug, NGK BPMR-8Y P/N A425000000 1 . Remove spark plug and check for fouling, worn and rounded center electrode. 2 . Clean the plug or replace with a new one.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 17 1 . Disconnect spark plug lead from spark plug. 2 . Remove (1) screw from top guard, and remove guard. 3 . Remove (4) screws from engine/muffler cover, and remove cover. 4 . Use the brush to remove dirt form cylinder fins.
18 6 . Assemble components in reverse order. NOTE When installing the engine/muffler cover, be certain the tabs of the metal deflector shield are in the slots of the cover.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 19 LUBRICA TION Blades Level 1. Tools Required: Clean rag, cleaning brush , oil can Parts Required: 20W Engine Oil (lubrication), 50-50 mixture of kerosene and 20W oil (cleaning) W ARNING DANGER Blades are very sharp.
20 Drive Shaft Assembly Level 1. NOTE Hedge Clipper drive shaft should be greased every 25 hours of operation. Tools required: 4 mm Hex wrench, screwdriver, clean rag, small brush Parts required: ECHO ® LUBE TM 14 oz. cartridge P/N 91015 or Lithium Based Grease W ARNING DANGER Blades are very sharp.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 21 SHARPENING BLADES Level 3. Tools required: (2) 10 mm wrenches, flat file, screwdriver Parts required: None W ARNING DANGER Hedge Clipper Blades are very sharp. Wear gloves to protect hands. 1 . Disconnect spark plug wire from spark plug.
22 T ROUBLESHOOTING W ARNING DANGER Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark near an open spark plug opening, otherwise serious personal injury may result.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 23 Long T erm S torage (over 30 days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage mainte- nance which includes the following: 1 . Store unit in a dry, dust free place, out of the reach of children.
DEALER? Call 1-800-432-ECHO or www .echo-usa.com S ER VICING I NFORMA TION P ARTS Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts always have the Model Number and Serial Number of the unit with you.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Echo SHC-210 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Echo SHC-210 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Echo SHC-210 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Echo SHC-210 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Echo SHC-210, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Echo SHC-210.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Echo SHC-210. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Echo SHC-210 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
