Manuale d’uso / di manutenzione del prodotto CS-330T del fabbricante Echo
Vai alla pagina of 32
X7503242504 X750009914 04/12 W ARNING Users of this equipment risk injury to themselves and others if the unit is used improperly and/or safety precautions are not followed. ECHO provides an operator ’s manual and a safety manual. Both must be read and understood for proper and safe operation.
2 R ules foR s afe o peRa tion A. Kickback Safety Precautions for Chain Saw Users Copyright© 2012 By Echo, Incorporated All Rights Reserved. B. Other Safety Precautions 1. Do not operate a chain saw with one hand! Serious injury to the operator , helpers, bystanders, or any com - bination of these persons may result from one-handed operation.
3 14. Keep the handles dry , clean, and free of oil or fuel mixture. 15. Operate the chain saw only in well-ventilated areas. 16. Do not operate a chain saw in a tree unless you have been specically trained to do so.
4 W ARNING The safety alert symbol accompanied by the word “W ARNING” calls attention to an act or condition which CAN lead to serious personal injury or death if not avoided. CIRCLE AND SLASH SYMBOL This symbol means the specic action shown is prohibited.
5 Carburetor adjustment - Idle speed Carburetor adjustment - High speed mixture Carefully read the Instruction manual Wear eyes, ears and head protection Carburetor adjustment - Low speed mixture Oil .
6 D esCRiption The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restric- tions, guide bar and saw chain installation and other assembly may be necessary . After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts.
7 1. Hand guard (Chain brake actuating lever) 2. Ignition/Choke Lever 3. Throttle control trigger 4. Throttle control lockout 5. Air cleaner cover 6. Pull starter 7. Front handle 8. Oil tank cap n oMenCla tuRe of p aRts Cs-330t , Cs-360t 10 11 12 13 14 9.
8 KICK GUARD® TO BAR INSTRUCTIONS For saws with Kick Guard ® P/N 2894901 and symmetri- cal or asymmetrical low-kick type guide bars. 1. Install bolt (A) in rear hole (B) of Kick Guard ® and through front hole (C) in guide bar . 2. IMPORT ANT : Dimple in Kick Guard ® (D) must engage recess in guide bar (E).
9 p o 7. T urn saw over and check brake band (O) for cor- rect position around clutch drum (P). If brake band is not in place around drum, remove clutch cover , make sure brake is released, and reinstall. DANGER Never operate saw if chain brake does not function properly , otherwise saw damage and serious personal injury could result.
10 NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty . Read and follow instructions in the Storage section of this manual.
11 o peRa tion IMPORT ANT This saw features a combination ignition/choke switch that automatically sets the throttle speed to fast idle for quick starting. Do not squeeze trigger during cold starts until after unit has started, or fast idle and choke set- tings will be released, and engine may not start.
12 5. Lay unit on a at, clear area and keep bar and chain clear of all obstacles. Hold top handle with one hand, and depress throttle trigger lockout (C), but do not depress throttle trigger (D). 6. Pull starter handle (F) several times until engine starts, or rst starting sound is heard.
13 A A E D D STOPPING 1. Release throttle trigger (D) and move lever (A) rearward to STO P ( O ) position. 2. Move chain brake lever (E) fully forward to lock chain brake. NOTE If engine does not stop, move ignition/choke lever forward to choke position ( ) to stop engine.
14 W ARNING Read the ECHO “CHAIN SA W SAFETY MANUAL” included with your chain saw for additional cutting and safety instruc- tions. Failure to obey all instructions may result in serious or fatal injuries. In all circumstances the operation of the chain saw is a one-man job.
15 W ARNING A falling tree can seriously damage anything it may hit - a car , a house, a fence, a power line, or another tree. There are ways to make a tree fall where you want it, so rst decide where that is! Before cutting, clear the area around the tree.
16 Don’t cut with the saw overhead or the bar in a vertical po- sition. If the saw should kick back you may not have good enough control to prevent possible injury . Bucking is the sawing of a log or fallen tree into smaller pieces. There are a few basic rules which apply to all bucking operations.
17 M aintenanCe anD C aRe W ARNING Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a com - plete stop before removing obstructions, clearing debris, or servicing unit.
18 AIR FIL TER 1. Close choke (Cold Start Position [ ]). This prevents dirt from entering the carburetor throat when the air lter is removed. Brush accumulated dirt from air cleaner area. 2. Remove air lter cover . Brush dirt from inside cover .
19 A B C GUIDE BARS AND OIL HOLES • Follow instructions for “Guide Bar and Saw Chain – Install/Re - move”. • Clean after each use -Clean the grooves (A) of the guide bar with a small screw- driver .
20 D Starter Side 1. Remove air lter cover and remove spark plug lead. 2. Remove plastic plug in side handle mount (D), and remove side handle mounting screw . 3. Remove four starter cover screws and remove starter cover . 4. Using a stiff bristle cleaning brush (do not use a metal brush), remove debris from ywheel and ignition coil area.
21 B C D E F G 6. Use a wood or plastic scraping tool to clean deposits from cylinder exhaust ports (G). 5. Remove mufer nuts (B), washer sets (C), eyeplate (D), mufer (E), and mufer gasket (F). Check parts for wear or damage, and replace if necessary .
22 CARBURETOR ADJUSTMENT Engine Break-In New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. Dur- ing the break-in period your engine performance will increase and exhaust emissions will stabilize.
23 HIGH AL TITUDE ADJUSTMENT 1. Start engine and run for several minutes to reach operating temperature. 2. Stop engine. 3. Start engine and turn the HI speed needle (A) lean (CW) until the engine runs between 13,500 and 14,500 RPM. Then turn the LO speed needle lean (B) (CW) until the engine does not hesitate when accelerated.
24 For setting saw chains, round le (4 mm ø: 5/32”) and at le are used. • T o keep correct position and correct angle, use the le holder . - Round le and at le are available from your Echo Dealer . • File cutters as below .
25 t RouBleshootinG T R A H C G N I T O O H S E L B U O R T M E L B O R P E N I G N E m e l b o r Pk c e h Cs u t a t Se s u a Cy d e m e R e n i g n E - s k n a r c / d r a h s t r a t s t ' n s.
26 The installation of a chain brake may be mandatory by law or as stipulated by insurance regulations in your area of operation. Y ou should inquire through local government ofces, your employer or your local dealer to ensure that your chain saw conforms to the required safety standard.
27 TESTING THE BRAKE • Start the engine on a solid level surface and run at a fast idle until warm. • Hold the saw rmly by the handles and accelerate the en - gine to a fast idle. OPERA TION • Set the lever in the released position before starting to cut.
28 t eChniCal D a t a * T echnical data subject to change without notice. Gasoline Use 89 Octane unleaded. Do not use fuel containing methyl alcohol, more than 10% ethyl alcohol or 15% MTBE. Do not use alternative fuels such as E-15 or E-85. Model CS-330T CS-360T Dimension L x W x H mm inch Weight Power head, dry kg Type Displacement 32.
29 ECHO LIMITED W ARRANTY ST A TEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated’s Limited W arranty , provides to the original purchaser that this ECHO product is free from defects in material and workmanship .
30 PURCHASED REP AIR P ARTS, SHORT BLOCKS AND ACCESSORIES .
31 ECHO INCORPORA TED EMISSION CONTROL W ARRANTY ST A TEMENT FOR ECHO AND SHINDAIW A BRANDS The Environmental Protection Agency (EP A) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE).
CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 Mon - Fri C.S.T . ECHO, INCORPORA TED 400 O AkwOOD R OAD L AkE Z uRich , iL 60047-1564 www .echo-usa.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Echo CS-330T è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Echo CS-330T - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Echo CS-330T imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Echo CS-330T ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Echo CS-330T, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Echo CS-330T.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Echo CS-330T. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Echo CS-330T insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
