Manuale d’uso / di manutenzione del prodotto P8 del fabbricante Earthquake Sound
Vai alla pagina of 16
Earthquake Sound Corporation 2727 Mc Cone A venue, Hayward, CA 94545 www .earthquakesound.com Sound That Will Move Y ou..
Safety Instructions 13. Damage Requiring Service — The Component 1. Read Instructions — All the safety and operation should be served only by EQ qualified serviced instructions should be read before the Earthquake personnel when: Component is operated.
W ARNING: The MiniMe subwoofers are capable of generating high sound pressure levels. Y ou should exercise caution when operating these speakers. Long term exposures to high levels of sound pressure will cause permanent damage to your hearing.
Earthquake • MiniMe User Manual 4 Introduction Please take a moment to fill out and mail the Earthquake W arranty Registration card. Also read the serial number located on the control panel and record it here: Unpacking Y our Earthquake subwoofer should reach you in perfect condition.
Earthquake • MiniMe User Manual 5 Control Panel Overview (4) Power Status LED (5) Line Level RCA Inputs (6) Sub Operation Switch (7) Auto ON/OFF (8) Speaker Level Inputs (9) Speaker Level Outputs (1.
Earthquake • MiniMe User Manual 6 (7) Auto ON/OFF (1 1) 1 10-120V AC Power When the main “POWER” ON/OFF switch is in the Connection “OFF” position, this switch has no affect on the The Earthquake MiniMe is equipped with a built in subwoofer .
Installation Observe the following general precautions and Route the power-supply cord so it is not likely to be read the safety instructions before powering your walked on or pinched by especially at plugs, Earthquake subwoofer . convenience receptacles, and the point where it exits from the unit.
AC outlets on the same circuit breaker Power strip T ape Deck DVD Pre-amplifier Amplifier Subwoofer Earthquake • MiniMe User Manual 8 • Choose reliable, high quality interconnect cables, Connections also called patch cords or RCA cables.
Earthquake • MiniMe User Manual 9 MiniMe 1 P= Passive Radiator A= Active Driver MiniMe 2 P A MiniMe 3 P A Location F a ct : S u b w o o f e r s r e p r o d u c e f r eq u e n c i e s w i t h and will still pressurize the room with lots of bass. wavelengths that are long in relation to the dimensions of most living rooms.
Earthquake • MiniMe User Manual 10 PRE-AMPLIFIER SUB/LFE OUT L R MAIN OUTPUTS + - AMPLIFIER INPUTS L R TO FRONT SPEAKERS + - System Configurations The following pages show some typical connections that you might make in your installation. They show how the inputs and outputs of the Earthquake sub are connected to your pre-amplifier or receiver .
Earthquake • MiniMe User Manual 1 1 PRE-AMPLIFIER L R MAIN OUTPUTS + - AMPLIFIER INPUTS L R TO FRONT SPEAKERS + - Connections to a pre-amplifier using “Y” cables If your pre-amplifier does not have a sub/LFE output, you can use “Y” cables to send its main outputs to both the subwoofer and your amplifier .
Earthquake • MiniMe User Manual 12 + - RECEIVER MAIN OUTPUTS L R TO FRONT SPEAKERS + - Using the line speaker-level inputs If you are using a receiver which does not have a subwoofer output or line level outputs (pre-outs), you can connect its speaker outputs to the subwoofer's Speaker-Level inputs.
Earthquake • MiniMe User Manual 13 Adjusting the controls There are two main methods for adjusting the level, crossover frequency and phase of the Earthquake MiniMe to match a system. ? Method One: T ypical: Listening and making adjustments to suit your taste.
Earthquake • MiniMe User Manual 14 Specification Amplifier Output 320 W atts (4.6-Ohm impedance) High Cut Filter 35Hz 100Hz adjustable. The crossover can be bypassed by rotating the crossover frequency control fully clockwise.
Earthquake • MiniMe User Manual 15 Limited 5-Y ear W arranty Earthquake warrants the original purchaser that all Factory Sealed New Audio Products to be free from defects in material and workmanship.
Earthquake Sound Corporation. 2727 Mc Cone Avenue, Hayward, California 94545. Ph (510) 732-1000. Fax (510) 732-1095 www .earthquakesound.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Earthquake Sound P8 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Earthquake Sound P8 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Earthquake Sound P8 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Earthquake Sound P8 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Earthquake Sound P8, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Earthquake Sound P8.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Earthquake Sound P8. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Earthquake Sound P8 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
