Manuale d’uso / di manutenzione del prodotto P10 del fabbricante Earthquake Sound
Vai alla pagina of 16
MiniMe P10 & P12 Models Earthquake Sound Corporation www .earthquakesound.com Sound That Will Move Y ou User's Manual.
Safety Instructions 13. Damage Requiring Service — The Component 1. Read Instructions — All the safety and operation should be served only by EQ qualified serviced instructions should be read before the Earthquake personnel when: Component is operated.
W ARNING: The MiniMe subwoofers are capable of generating high sound pressure levels. Y ou should exercise caution when operating these speakers. Long term exposures to high levels of sound pressure will cause permanent damage to your hearing.
Introduction Please take a moment to fill out and mail the Earthquake W arranty Registration card. Also read the serial number located on the control panel and record it here: Unpacking Y our Earthquake subwoofer should reach you in perfect condition.
(1) Line Level RCA Inputs terminals will accept up to 16-gauge quality speaker Connect with RCA type patch cords to the line level wire. The Inputs should be connected to the left and output of your receiver or pre-amp. If your pre- right speaker terminals of your amplifier or receiver .
(6) Auto ON/OFF (10) Sub Operation Switch When the main “POWER” ON/OFF switch is in the In LFE position, the Frequency adjustment becomes “OFF” position, this switch has no affect on the disabled and the subwoofer runs in a Full range subwoofer .
• Do not let anything come into contact with the panel Installation and keep at least two inches away from any walls. Observe the following general precautions and read the safety instructions before powering your The metal control plate serves as the amplifier heat Earthquake subwoofer .
AC outlets on the same circuit breaker Power strip T ape Deck DVD Pre-amplifier Amplifier Subwoofer Connections • This diagram shows all the low power components Please consider the following when setting up sharing a power strip which is connected to the same your new system: outlet used by the amplifier .
MiniMe 1 P= Passive Radiator A= Active Driver MiniMe 2 P A MiniMe 3 P A Location F a c t : S u b w o o f e r s r e p r o d u c e f r e q u e n c i e s w i t h #1 is very good positioning. wavelengths that are long in relation to the dimensions of most living rooms.
System Configurations The following pages show some typical connections that you might make in your installation. They show how the inputs and outputs of the Earthquake sub are connected to your pre-amplifier or receiver .
Connections to a pre-amplifier using “Y” cables If your pre-amplifier does not have a sub/LFE output, you can use “Y” cables to send its main outputs to both the subwoofer and your amplifier . The subwoofer will play the low frequency range and your front speakers will play the full range.
Earthquake Sound, 2727 McCone Avenue, Hayward, CA 94545 USA www.earthquakesound.com VOLUME FREQUENCY MODE PHASE AUTO MIN 50Hz MAX RIGHT POWER LEFT 160Hz SUB 0 OFF LFE 180 ON 110-120VAC~60Hz 220-240VAX~50Hz FUSE: 115V , T6.
AUTO OFF ON VOLUME FREQUENCY MODE PHASE MIN 50Hz MAX 160Hz SUB 0 LFE 180 Adjusting the controls There are two main methods for adjusting the level, crossover frequency and phase of the Earthquake MiniMe to match a system. ? Method One: T ypical: Listening and making adjustments to suit your taste.
MiniMe P10 Specifications MiniMe P12 Specifications Amplifier Output Amplifier Output 600 W atts (4-Ohm impedance) 600 W atts RMS (4-Ohm impedance) High Cut Filter High Cut Filter 50Hz-160Hz adjustable.
Limited 5-Y ear W arranty Earthquake warrants the original purchaser that all Factory Sealed New Audio Products to be free from defects in material and workmanship under normal and proper use for a period of five (5) years from the date of purchase (as shown on the original bill of sale with serial number affixed/written on it).
Earthquake Sound Corporation 2727 Mc Cone A venue, Hayward, California 94545 Ph (510) 732-1000 Fax (510) 732-1095 www .earthquakesound.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Earthquake Sound P10 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Earthquake Sound P10 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Earthquake Sound P10 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Earthquake Sound P10 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Earthquake Sound P10, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Earthquake Sound P10.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Earthquake Sound P10. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Earthquake Sound P10 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
