Manuale d’uso / di manutenzione del prodotto XP-Z3C del fabbricante Aiwa
Vai alla pagina of 32
XP-Z3C COMP ACT DISC PLA YER REPRODUCT OR DE DISCOS COMP ACTOS OPERA TING INSTRUCTIONS INSTRUCCIONES DE MANEJO MODE D’EMPLOI W ARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
2 ENGLISH NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
ENGLISH 3 ENGLISH To maintain good performance • Do not use the unit in places which are extremely hot, cold, dusty or humid. In particular, do not use or keep the unit in following places. • in a high humidity area such as a bathroom • near a heater • in an area exposed to direct sunlight (e.
4 ENGLISH USING ON RECHARGEABLE BA TTERIES When using on the rechargeable batteries for the first time, charge them until the battery indicators go out. 1 Insert the supplied rechargeable batteries with the 0 and 9 marks correctly aligned. 2 Place the unit on the charging stand,and then connect the AC adaptor.
ENGLISH 5 ENGLISH To detach the unit from the charging stand Lift the unit upward while holding the charging stand. Time to recharge the batteries The battery indicator in the display changes from to according to the remaining power of the batteries. Recharge the batteries when lights and “Low- Batt” appears.
6 ENGLISH USING ON DR Y CELL BA TTERIES Use the supplied battery case. 1 Open the battery compartment of the supplied battery case,and insert two LR6 (size AA) alkaline batteries with the 0 and 9 marks correctly aligned. 2 Attach the battery case to the unit.
ENGLISH 7 ENGLISH BEFORE PLA YBACK Using with the headphones Connect the supplied headphones, remote control, and main unit. • Be sure to press s to stop operation before you connect/disconnect the headphone or the remote control to/from the main unit.
8 ENGLISH BEFORE PLAYBACK Turning on and off Turning the power on Press e on the unit or c / a on the remote control. Power is turned on and playback starts. Note “ERROR” appears on the display when you play a disc placed upside-down or a defective disc.
ENGLISH 9 ENGLISH DSL* DSL Press DSL on the remote control repeatedly for more powerful sound and deeper bass. : Deep bass is emphasized : Normal sound *DSL: Dynamic Super Linear Bass Loading a disc 1 Slide the OPEN switch to open the disc compartment.
10 ENGLISH 2 Place a disc in the center with the label side facing up. 3 Close the disc compartment. To remove the disc Pick up the disc, holding its edge, while holding the pivot gently pressed. Note • The unit is designed for 8 cm discs only. • The unit can play a CD-R/RW disc recorded in MP3 or CD-DA format.
ENGLISH 11 ENGLISH 4 Press e on the unit or c / a on the remote control. Playback starts from the first track. 2 1 2 3 4 4 3 PLA YBACK OF AUDIO DISC 1 Connect the supplied headphones to the jack.
12 ENGLISH Basic operation To locate the track 10 tracks ahead of the current track (+10 skip) In Play or Standby mode, press +10 on the remote control. Ex. 1: If you press +10 while the unit is playing the 4th track, the beginning of the 14th track is located.
ENGLISH 13 ENGLISH OTHER FUNCTIONS You can set various functions by using P-MODE/ENT, i / k , and r / t on the remote control. Basic operating procedure 3 Press r or t repeatedly to select your desired setting*. * For details on the settings, see the following instructions respectively.
14 ENGLISH OTHER FUNCTIONS E•A•S•S (Electronic Anti-Shock System) The E•A•S•S function reduces skipping or muting of the sound when the unit is subjected to shocks. 1 Perform steps 1 and 2 in “Basic operating procedure” to select “EASS 40sec.
ENGLISH 15 ENGLISH 3 Perform steps 4 and 5 in “Basic operating procedure.” : All-track repeat : One-track repeat To cancel the REPEAT play Select “REPEAT OFF” in step 2.
16 ENGLISH 3 Press r or t repeatedly to select a track to be added to the program. a Selected track number (flashing) b Program order 4 Press P-MODE/ENT. The selected track is stored in the program. Repeat steps 3 and 4 to program more tracks. 5 Press e on the unit or c / a on the remote control to start program play.
ENGLISH 17 ENGLISH NOTES ON MP3 FILES • An MP3 file stores audio data compressed using MPEG1/2/2.5, the audio layer-3 file-coding scheme. • In this manual, CDs, CD-R discs and CD-RW discs are all referred to as “discs”. We refer to what are called “folder” and “file” in PC terminology as “album” and “track”.
18 ENGLISH NOTES ON MP3 FILES This unit can play back MP3 files of the following sampling frequencies: MPEG 1: 32k, 44.1k, 48 kHz MPEG 2: 16k, 22.05k, 24 kHz MPEG 2.5: 8k, 11.025k, 12 kHz Notes on display indications during play • Up to 64 characters (including its extension) are displayed for the name of an album or a track.
ENGLISH 19 ENGLISH 3 Include a two- or three- digit number at the beginning of each album or track name so that the albums and tracks are played in order. <example of recommended names> 01XXXXX.mp3 02XXXXX.mp3 03XXXXX.mp3 04XXXXX.mp3 05XXXXX.mp3 <example of names not recommended> 1XXXXX.
20 ENGLISH PLA YBACK OF MP3 DISCS 5 Press e on the unit or c / a on the remote control to start playback. Power is turned on and “READING” flashes in the display.
ENGLISH 21 ENGLISH When you play an MP3 disc The E•A•S•S function will be activated automatically. Setting the QUICK/NORMAL switch Set the switch to the appropriate position depending on the playback mode and type of disc. QUICK The unit reads only the number of the album before playback, then disc reading finishes earlier.
22 ENGLISH To change the album Press i / k . To skip to the first track of next album, press i . To skip to the first track of previous album, press k . To locate the track 10 tracks ahead of the current track (+10 skip) In play or standby mode, press +10 on the remote.
ENGLISH 23 ENGLISH Note • If the disc has no ID3 TAG information, “NO TITLE” appears on the display. • If you press s , normal display resumes.
24 ENGLISH Resume function Set the HOLD/RESUME switch to RESUME. OFF HOLD RESUME You can start playback from the point where you stopped playback by pressing s . When the resume function is on, all-track repeat is selected automatically. To cancel resume function, set the HOLD/ RESUME switch to OFF.
ENGLISH 25 ENGLISH Random play You can play all the tracks on the disc in random order. Be sure to set the QUICK/NORMAL switch to its NORMAL position before random play. 1 Perform steps 1 and 2 in “Basic operating procedure” to select “RANDOM OFF.
26 ENGLISH 3 Press i / k (for album selection) and r / t (for track selection) repeatedly to select a track to be added to the program. a Selected album number (flashing) b Selected track number (flashing) c Program order 4 Press P-MODE/ENT. The selected track is stored in the program.
ENGLISH 27 ENGLISH CONNECTING AN EXTERNAL UNIT Use a commercially available connection cord which has a 3.5 ø stereo mini-plug at one end and two phono plugs at the other end. Connect the stereo mini-plug to the headphone jack of the remote control and connect the phono plugs to the analog input terminals of the external unit.
28 ENGLISH To clean the discs Before playing, wipe the disc from the center outward with a cleaning cloth. After playing, store the disc in its case. MAINTENANCE To clean the lens If the lens becomes dirty, the player will skip or not play. If this occurs, clean the lens in the following manner.
ENGLISH 29 ENGLISH ISO 9660 ISO stands for the “International Organization for Standardization.” ISO 9660 determines the file structure for the CD-ROMs. This unit can play MP3 files recorded in the format compliant with ISO 9660. Nesting of folders (albums) To organize data files stored in a PC, you can store related files in a folder.
30 ENGLISH SPECIFICA TIONS Tracking system 3-beam laser Laser pickup Semiconductor laser D/A conversion 1 bit DAC Frequency response 20 - 20,000 Hz (47 k ohms) Output jack (stereo mini-jack) Maximum output 10 mW + 10 mW (16 ohms at 1 kHz) 450 mV (47 k ohms at 1 kHz) Power supply DC 2.
ENGLISH 31 ENGLISH Maximum outside dimensions 90 (W) × 28 (H) × 104 (D) mm (3 5 / 8 × 1 1 / 8 × 4 1 / 8 in.) (excluding projecting parts and controls) Weight Approx.
8B-HP3-901-11 020205BKK-O-T A Printed in Japan.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Aiwa XP-Z3C è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Aiwa XP-Z3C - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Aiwa XP-Z3C imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Aiwa XP-Z3C ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Aiwa XP-Z3C, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Aiwa XP-Z3C.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Aiwa XP-Z3C. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Aiwa XP-Z3C insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
