Manuale d’uso / di manutenzione del prodotto 2008 Ram 2500 del fabbricante Dodge
Vai alla pagina of 527
Ram T ruc k OWNER’ S MANUAL 2008 2008 Ram T ruc k 81-326-0827 First Edition Printed in U.S.A..
VEHICLES SOLD IN CANADA W ith respect to any V ehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor . DRIVING AND ALCOHOL Drunken driving is one of the most fr equent causes of accidents.
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION .............................................................3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ............................... 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...........
.
INTRODUCTION CONTENTS m Introduction ........................... 4 m A Message From DaimlerChrysler Corporation . . . 4 m How T o Use This Manual .................. 5 m W arnings And Cautions ................... 7 m V an Conversions/Campers ..........
INTRODUCTION This Owner’s Manual has been prepar ed with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a W arranty Information Booklet and various customer-oriented documents.
follow and careful adher ence to them will ensure that you take full advantage of the features of this engine. Thank you for choosing the Cummins t T urbo Diesel powered tr uck. HOW TO USE THIS MANUAL Consult the T able of Contents to determine which section contains the information you desire.
6 INTRODUCTION.
W ARNINGS AND CAUTIONS This Owner’s Manual contains W ARNINGS against op- erating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against proce- dures which could r esult in damage to your vehicle. If you do not read this entir e manual, you may miss important information.
VEHICLE IDENTIFICA TION NUMBER The V ehicle Identification Number (VIN) is found on the left front corner of the instr ument panel, visible through the windshield. This number also appears on the Auto- mobile Information Disclosure Label af fixed to a window on your vehicle, the vehicle registration and title.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS m A W ord About Y our Keys .................. 1 2 ▫ Ignition Key Removal ................... 1 2 ▫ Locking Doors W ith The Key .............. 1 4 m Sentry Key t ........................... 1 5 ▫ Replacement Keys .
m Remote Keyless Entry — If Equipped ......... 2 1 ▫ T o Unlock The Doors ................... 2 2 ▫ T o Lock The Doors ..................... 2 3 ▫ Using The Panic Alarm .................. 2 4 ▫ General Information .................... 2 5 ▫ T ransmitter Battery Service .
▫ Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags ........... 4 8 ▫ Event Data Recorder (EDR) ............... 5 9 ▫ Child Restraint ........................ 6 1 m New Engine Break-In ..................... 7 4 m Safety T ips .
A WORD ABOUT YOUR KEYS The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys fr om your authorized dealer . Ask your authorized dealer for these numbers and keep them in a safe place.
NOTE: If you try to remove the key befor e you place the shift lever in P ARK, the key may become trapped tem- porarily in the ignition cylinder . If this occurs, rotate the key to the right slightly , then remove the key as de- scribed.
CAUTION! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. Manual T ransmission — If Equipped When the steering wheel is in the LOCK position, the steering and ignition systems are locked to pr ovide antitheft protection for your vehicle.
SENTR Y KEY T The Sentry Key t Immobilizer system prevents unautho- rized vehicle operation by disabling the engine. The system does not need to be armed or activated.
• Exxon/Mobil Speedpass™, additional Sentry Keys t , or any other transponder-equipped components on the same key chain will not cause a key-related (transponder) fault unless the additional part is physi- cally held against the ignition key being used when starting the vehicle.
Customer Key Programming If you have two valid Sentry Keys t , you can program new Sentry Keys t to the system by performing the following procedur e: 1. Cut the additional Sentry Key t T ransponder blank(s) to match the ignition switch lock cylinder key code.
NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased fr om the sys- tem’s memory . This will prevent the lost key from starting your vehicle. The remaining keys must then be repr ogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be repr o- grammed.
NOTE: If you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right to disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it.
being set. After the alarm is set, the SECURITY light will flash at a slower rate to indicate that the system is armed. NOTE: If the SECURITY light stays on continuously during vehicle operation, have the system checked by an authorized dealer . T o Disarm the System: Use the RKE transmitter to UNLOCK the door .
NOTE: • The front courtesy over head console and door cour- tesy lights do not turn off if the dimmer contr ol is in the interior lights ON position (extreme top position). • The illuminated entry system will not operate if the dimmer control is in the extr eme downward position.
T o unlock the doors: Press and r elease the UNLOCK button on the Remote Keyless Entry (RKE) transmitter once to unlock only the driver’s door or twice to unlock all the doors.
T o lock the doors: Press and r elease the LOCK button on the RKE transmit- ter to lock all doors. If the ignition is OFF when the doors are locked, the parking lights will flash on once and the horn will chirp once. Park Lights Flash Feature Programming V ehicles will be shipped from the assembly plants with the park light flash feature activated.
(Customer Programmable Featur es)” under “Over- head Console with Electronic V ehicle Information Center (EVIC) – If Equipped” in Section 3. • For vehicles not equipped with the EVIC, perform the following procedur e: 1. Perform this operation while standing outside the vehicle.
General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interfer ence that may cause undesired operation.
NOTE: Perchlorate Material – special handling may apply , refer to www .dtsc.ca.gov/hazardouswaste/perchlorate. The recommended r eplacement battery is CR2032 bat- tery . NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit boar d.
W ARNING! • For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons.
chime will sound if the key is in the ignition switch and a door is open, as a reminder to r emove the key . Automatic Door Locks – If Equipped If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (25 km/h).
8. If a chime is not heard, the program mode was canceled before the featur e could be disabled. If neces- sary , repeat the above procedur e. Auto Unlock On Exit — If Equipped This feature unlocks all of the doors of the vehicle when any door is opened.
7. Repeat the above steps to alternate the availability of this feature. 8. If a chime is not heard, the program mode was canceled before the featur e could be changed.
W ARNING! A void trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
WINDOWS Power Windows – If Equipped The control on the left fr ont door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window contr ol and on the rear doors of Quad Cab t and Mega Cab t models.
Auto Down (Driver’s Side Only) The driver’s window switch has an Auto Down feature. Press the window switch past the detent, r elease, and the window will go down automatically . W indow Lockout Switch (4-Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors.
Power Sliding Rear Window – If Equipped The power sliding rear window switch is located on the instrument panel below the climate contr ols. Press the right side of the switch to open the glass and the left side of the switch to close the glass.
OCCUP ANT RESTRAINTS Some of the most important safety features in your vehicle are the r estraint systems. These include the front and rear seat belts for the driver and all passengers, fr ont airbags for both the driver and front passenger and, if equipped, window bags for the driver and passengers seated next to a window .
of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions except the Quad Cab t front center seating position have combination lap/shoulder belts.
W ARNING! • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision the best. W earing your belt in the wrong place could make your injuries in a collision much worse.
3. When the belt is extended long enough to fit, insert the latch plate into the buckle until you hear a “click.” 1 — Latch Plate Latch Plate T o Buckle 38 THINGS TO KNOW BEFORE ST ARTING YOUR V.
W ARNING! • A belt buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
W ARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. • A twisted belt can’t do its job as well.
Regular Cab Front Center Three-Point Belt 1. The front center seat belt on the Regular Cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger seat.
W ARNING! • If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted.
W ARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly . Adjustable Upper Shoulder Belt Anchorage In the front r ow outboard seats, the shoulder belt can be adjusted upward or downwar d to help position the belt away from your neck.
As a guide, if you are shorter than average, you will prefer a lower position, and if you ar e taller than average, you’ll prefer a higher position. When you r elease the anchorage, try to move it up or down to make sure that it is locked in position.
Center Lap Belts The center seating position for the Quad Cab t front seat has a lap belt only . T o fasten the lap belt, slide the latch plate into the buckle until you hear a 9 click. 9 T o lengthen the lap belt, tilt the latch plate and pull. T o remove slack, pull the loose end of the webbing.
Enhanced Seat Belt Reminder System (BeltAlert T ) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced W arning System (BeltAlert t ) will alert the driver to buckle the seat belt.
The Enhanced W arning System (BeltAlert t ) can be reac- tivated by repeating this pr ocedure. NOTE: Although the Enhanced W arning System (BeltAlert t ) has been deactivated, the Seat Belt W arning Light will continue to illuminate while the driver’s seat belt remains unbuckled.
Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt r estraint systems. The driver’s front airbag is mounted in the steering wheel.
W ARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured be- cause the airbags are no longer functional. These protective covers for the airbag cushions are de- signed to open only when the airbags are inflating.
Here ar e some simple steps you can follow to minimize the risk of harm from a deploying airbag. 1. Children 12 years and under should always ride buckled up in a rear seat in an appr opriate child restraint.
W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly . In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
• Driver and Front Passenger Seat Belt Pr etensioners (if equipped) • Driver Seat T rack Position Sensor (if equipped) • Passenger Side Frontal Airbag ON/OFF Switch (2500/ 3500 Regular Cab V ehi.
W ARNING! Ignoring the AIRBAG warning light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away .
• The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel. When the ORC detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airbags.
• The Knee Impact Bolsters help protect the knees of the driver and the front passenger , and positions them for the best interaction with the front airbag.
W ARNING! Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash.
If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and fr ont passenger as the airbags deploy and unfold.
Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured if the airbag system is not there to protect you.
• The light remains on or flickers after the six to eight- second interval. • The light flickers or comes on and remains on while driving. NOTE: If the speedometer , tachometer or any engine- related gauges ar e not working, the airbag control mod- ule may also be disabled.
In the event that an investigation is undertaken by DaimlerChrysler Corporation (regar dless of initiative), the company or its designated repr esentative will first obtain permission of the appropria.
• Airbag deployment level (if applicable) • Impact acceleration and angle • Seat Belt status • Brake status (service and parking brakes) • Accelerator status (including vehicle speed) • En.
W ARNING! In a collision, an unrestrained child, even a tiny baby , can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured.
unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position. • Children who weigh mor e than 20 lbs (9 kg) and who are older than one year can ride forwar d-facing in the vehicle.
Here are some tips for getting the most out of your child restraint: • Before buying any r estraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. W e also recommend that you make sure that you can install the child restraint in the vehicle where you will use it befor e you buy it.
around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secur e, try a differ ent seating position. • Buckle the child into the seat according to the child restraint manufactur er’s directions.
NOTE: For children riding in the fr ont seat of a Regular Cab model, refer to the “Passenger Airbag ON/OFF Switch” located in this section. Regular Cab Passenger Seat Quad Cab t Rear Outboard Seat.
Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage, have been available for some time.
of reach of childr en. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach.
rearwar d-facing infant restraints will also be equipped with a tether strap, a hook and means for adjusting the tension in the strap. In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages.
W ARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
Multiple Child Restraint Installation Sequence - (Quad Cab t Rear Seats) 1. Obtain tether straps by raising the head restraints and reaching between the r ear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly impr oved by raising the seat cushion to the “up” position.
Multiple Child Restraints 72 THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE.
T ether Anchorage Points at All Three Seating Positions (Mega Cab t ) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seatback under the head restraint to the tether anchor dir ectly behind the seat.
• Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically . A child’s squirming or slouching can move the belt out of position. If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle.
• Check the coolant and oil levels frequently . • V ary throttle position at highway speeds when carry- ing or towing significant weight. Because of the construction of the Cummins t Diesel engine.
Lock Y our V ehicle Always remove the key fr om the ignition and lock all doors when leaving the vehicle unattended, even in your own driveway or garage. T ry to park your vehicle in a well-lighted area and never invite theft by leaving ar - ticles of value exposed.
Safety Checks Y ou Should Make Inside The V ehicle Heater Defroster Ducts Inspect the heater defroster ducts for pr oper operation. Check for proper airflow thr ough all defroster ducts. If there ar e any questions regarding the operation of your heater defroster ducts, have the system checked by an authorized dealer .
Safety Checks Y ou Should Make Outside The V ehicle T ires Examine tires for tr ead wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks. Check wheel nuts for tightness and tires for pr oper pressure.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS m Mirrors ............................... 8 4 ▫ Inside Mirror ......................... 8 4 ▫ Automatic Dimming Mirror – If Equipped .... 8 5 ▫ Outside Mirrors ....................... 8 5 ▫ Exterior Mirrors Folding Featur e .
m Seats ................................ 1 1 5 ▫ 40-20-40 Front Seat .................... 1 1 6 ▫ Reclining Seats ....................... 1 1 7 ▫ Adjustable Head Restraints .............. 1 1 8 ▫ Manual Rotary Lumbar Support Adjustment — If Equipped .
m Electronic Speed Contr ol — If Equipped ...... 1 3 9 ▫ T o Activate .......................... 1 4 0 ▫ T o Set At A Desir ed Speed ............... 1 4 0 ▫ T o Deactivate ........................ 1 4 0 ▫ T o Resume Speed ...................
▫ Pinch Protect Override ................. 1 5 9 ▫ V enting Sunroof - Express ............... 1 6 0 ▫ Sunshade Operation ................... 1 6 0 ▫ W ind Buffeting ....................... 1 6 0 ▫ Sunroof Maintenance ................... 1 6 0 ▫ Sunroof Fully Closed .
m Rear W indow Features ................... 1 7 3 ▫ Electric Rear W indow Defroster And Heated Sideview Mirrors — If Equipped .......... 1 7 3 ▫ Power Sliding Rear W indow — If Equipped . . 173 ▫ Sliding Rear W indow — If Equipped ....... 1 7 4 m Fold Flat Load Floor — If Equipped .
MIRRORS Inside Mirror The mirror should be adjusted to center on the view through the r ear window . Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
Automatic Dimming Mirror – If Equipped This mirror automatically adjusts for annoying headlight glare fr om vehicles behind you. Y ou can turn the feature on or off by pr essing the button at the base of the mirror . A light in the button will indicate when the dimming feature is activated.
W ARNING! V ehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an- other vehicle or other object.
Set the top switch to the left or right for the left or right mirror , and set it to the center off position to pr event accidentally moving a mirror when you ar e finished adjusting the mirror . T o adjust a mirror , select left or right with the top switch, and press one of the four arr ows for the direction you want the mirr or to move.
extra-wide loads. T o change position inboard or out- board, the mirr or head should be rotated (flipped out or in). A small blindspot mirror is integrated onto the main mirror surface. NOTE: Fold the trailer towing mirrors rearward prior to entering an automated car wash.
HANDS-FREE COMMUNICA TION (UConnect T )— IF EQUIPPED NOTE: The sales code RER radio contains an inte- grated Hands-Free Communication (UConnect t ) sys- tem. Refer to your “Navigation User’s Manual” for UConnect t system operating instructions for this radio.
differ ent electronic devices to connect to each other without wires or a docking station, so UConnect t works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s UConnect t system.
The radio display will be used for visual prompts fr om the UConnect t system such as 9 CELL 9 or caller ID on certain radios. Operation V oice commands can be used to operate the UConnect t system and to navigate through the UConnect t menu structur e.
T o activate the UConnect t system from idle, simply pr ess the PHONE button and follow the audible prompts for directions. All UConnect t system sessions begin with a press of the PHONE button on the radio contr ol head. Cancel Command At any prompt, after the beep, you can say 9 Cancel 9 and you will be returned to the main menu.
• Y ou will then be asked to give your cellular phone a priority level between 1 and 7, with 1 being the highest priority . Y ou can pair up to seven cellular phones to your UConnect t system. However , at any given time, only one cellular phone can be in use, connected to your UConnect t system.
• The system will prompt you to say the name of the person you want to call. • After the 9 Ready 9 prompt and the following beep, say the name of the person you want to call. For example, you can say 9 John Doe, 9 where John Doe is a pr evi- ously stored name entry in the UConnect t phonebook.
The UConnect t system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. Phonebook Download UConnect t allows the user to download entries from their phone via Bluetooth t .
• Y ou will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit. • When prompted, r ecite the new phone number for the phonebook entry that you are editing.
• After you enter the name, the UConnect t system will ask you which designation you wish to delete: home, work, mobile, pager , or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted.
Phone Call Features The following features can be accessed thr ough the UConnect t system if the feature(s) ar e available on your cellular service plan. For example, if your cellular service plan provides thr ee-way calling, this feature can be accessed through the UConnect t system.
to 9 T oggling Between Calls 9 in this section. T o combine two calls, refer to 9 Confer ence Call 9 in this section. Place/Retrieve a Call From Hold T o put a call on hold, press the PHONE button until you hear a single beep. This indicates that the call is on hold.
• After the 9 Ready 9 prompt and the following beep, say 9 Redial. 9 • The UConnect t system will call the last number that was dialed from your cellular phone.
After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every UConnect t language change opera- tion, only the language-specific 32-name phonebook is usable. The paired phone name is not language-specific and usable across all languages.
T owing Assistance If you need towing assistance: • Press the PHONE button to begin. • After the 9 Ready 9 prompt and the following beep, say 9 T owing Assistance. 9 NOTE: The T owing Assistance number dialed is based on the country where the vehicle is pur chased (1-800-528- 2069 for the U.
sequence on your cellular phone keypad, you can press the “V oice Recognition” button and say the sequence you wish to enter , followed by the word 9 Send. 9 For example, if requir ed to enter your PIN followed with a pound, (3 7 4 6 #), you can press the “V oice Recognition” button and say , 9 3746# Send.
• Press the PHONE button to begin. • After the 9 Ready 9 prompt and the following beep, say 9 Setup Confirmations. 9 The UConnect t system will play the current confirmation pr ompt status and you will be given the choice to change it.
• Following the beep, say 9 Mute. 9 In order to un-mute the UConnect t system: • Press the “V oice Recognition” button. • Following the beep, say 9 Mute off.
• The UConnect t system will play the phone names of all paired cellular phones in or der from the highest to the lowest priority . T o “select” or “delete” a paired phone being announced, press the “V oice Recogni- tion” button and say “Select” or “Delete.
Things Y ou Should Know About Y our UConnect T System UConnect t T utorial T o hear a brief tutorial of the system features, pr ess the PHONE button and say “UConnect t T utorial.
• Speak normally , without pausing, just as you would speak to a person sitting a few feet/meters away from you. • Make sure that no one other than you is speaking during a voice recognition period.
• In a convertible vehicle, system performance may be compromised with the convertible top down. Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, •.
1 10 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 1 1 1 3.
1 12 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
V oice Commands Primary Alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all V oice Commands Primary Alternate(s) call cancel confirmation prompt.
V oice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous recor d again redial V oic.
General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference r eceived, including interference that may cause undesir ed op- eration.
40-20-40 Front Seat As the name implies, the seat is divided into three segments. The outboard seat portions ar e each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armr est/center storage compartment (if equipped).
Reclining Seats The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seatback and adjust for comfort. W ARNING! Y ou can be seriously , even fatally , injured riding in a seat with the seatback reclined.
Adjustable Head Restraints Head restraints can r educe the risk of neck injury in the event of impact from the r ear . Pull up or push down on the restraints so that the upper edge is as high as practical, at least to the level of the ears. T o lower the head restraint, push in the button and then push down on the head restraint.
Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback and on the right side of the passenger’s seatback increases or decr eases the lumbar (lower back) support. Power Seats — If Equipped CAUTION! Don’t put anything under a power seat.
The power seat controls ar e on the outboard side of the front seat cushions. Thr ee switches control the seat move- ment. The four-way switch in the center can be moved forward or backwar ds to get the most comfortable posi- tion. The same switch can be moved up and down to control seat height.
Rear Seat Features — Mega Cab Models Reclining Rear Seats — Mega Cab Models The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seatback and adjust for comfort. Folding Rear Seat (T able Mode) — Mega Cab Models Both the left and right rear sea backs can be folded down and used as a table.
T able Mode Handle T able Mode 122 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
Folding Rear Seat (Kneel Mode) — Mega Cab Models Both the left and right rear seats can be folded flat (Kneel Mode) and used for carrying cargo. Each of the r ear seatbacks provide two D-rings and each of the r ear storage bin lids provide two slotted cutouts.
W ARNING! Cargo must be securely tied down before driving your vehicle. Improperly secured cargo can fly around in a sudden stop and strike someone in the vehicle, causing serious injury or possible death. Secure cargo with a cargo tie down using the D-Rings provided on the back of the seats and the slotted cutouts in the rear storage bin lid.
W ARNING! Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury .
Heated Seats — If Equipped The heated seat switches are located in the instr ument panel under the climate controls. Each heated seat switch has two settings (HI and LOW). Press the switch once to obtain High heat level, then press the switch again to obtain Low heat level.
W ARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater . It may cause burns even at low temperatures, especially if used for long periods of time.
T o open the hood, two latches must be released. First pull the hood release lever located below the steering wheel at the base of the instrument panel. Once the hood is released you must r each into the opening beneath the center of the grille and push up the latch to release the safety catch before raising the hood.
LIGHTS Interior Lights Headlight Switch Location Dimmer Control UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 129 3.
Courtesy and dome lights are turned on when the fr ont doors are opened, when the dimmer contr ol (rotating wheel on the right side of the switch) is rotated to the upward detent position, or if equipped, when the UN- LOCK button is pressed on the key fob.
Headlamp Delay T o aid in your exit, your vehicle is equipped with a headlamp delay that will leave the headlamps on for 90 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is ON, and then the headlamp switch is cycled OFF .
T o minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. T o remove r oad dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses.
Cargo Light — If Equipped The cargo lights ar e turned ON by pressing on the CARGO button. The interior lights will also turn on when the cargo lights ar e on. The cargo lights will also turn ON for 30 seconds when a key fob UNLOCK is pressed, as part of the illuminated entry featur e.
Y ou can signal a lane change by moving the lever partially up or down. T urn Signal Auto Mode T ap the multifunction control lever once and the turn signal (left or right) will flash three times, and automati- cally turn off.
WINDSHIELD WIPERS AND W ASHERS Windshield Wipers High Beam / Low Beam W indshield Wiper / W asher Switch UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 135 3.
The wipers and washers are operated by a switch in the multifunction control lever . T urn the end of the handle to select the desired wiper speed. Intermittent W iper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable.
while in the OFF position, the wiper will wipe approxi- mately three wipes after the wash knob is r eleased. T o prevent fr eeze-up of your windshield washer system in cold weather , select a solution or mixture that meets or exceeds the temperature range of your climate.
W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.
Adjustment 1. Position the driver seat so that you are at least 10 in (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch, located to the left of the steering column near the parking brake release, in the direction you desir e to move the pedals.
NOTE: The Electronic Speed Contr ol System has been designed to shut down if multiple speed control switch buttons (i.e., SET and CANCEL) are operated simulta- neously , in order to ensure pr oper operation. The system can be reactivated by pushing the speed contr ol switch ON/OFF button and re-establishing the desir ed vehicle SET speed.
T o Resume Speed T o resume a pr eviously set speed, push and release the RESUME button. Resume can be used at any speed above 30 mph (50 km/h). T o V ary The Speed Setting When the speed control is on, speed can be incr eased by pressing and holding the RESUME/ACCEL button.
V ehicles equipped with a 4–speed automatic transmis- sion may exhibit several 4-3 downshifts under the above conditions. T o reduce the fr equency of the downshifts and to improve vehicle performance, it is advisable to lock out overdrive by pr essing the O/D OFF button located at the end of the gear shifter .
Electronic V ehicle Information Center (EVIC) — If Equipped Pressing the menu button will change the display to one of the following features: Dome/Reading Lights Overhead Console with EVIC UNDERST .
T rip Functions Pressing the STEP button allows you to scroll through one of the following T rip Function features: • TRIP – Shows the total distance traveled since the last reset. T o reset the TRIP function, pr ess and hold the RESET button. • ELAPSED TIME – Shows the total elapsed time of travel since the last reset.
will continue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the 9 LOW FUEL 9 text and a new DTE value will display .
indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position.
Press and r elease the Menu button until the Personal Settings displays on the EVIC. Use the STEP button to display one of the following: • “LANGUAGE” – When in this display you may select one of three languages for all display nomenclatur e, including the trip functions.
• “SOUND HORN W/LOCK > ON” – When ON is selected, a short horn sound will occur when the remote keyless entry LOCK button is pr essed. This feature may be selected with or without the flash lights on lock/unlock feature. T o make your selection, press and release the RESET button until “ON” or “OFF” appears.
NOTE: If this feature is enabled, the headlamps will be on during the engine pre-heat and cold crank; ther efore, it is recommended that the featur e be disabled when overnight ambient temperature is at or below 20°F (-7°C) to prevent excessive drain on batteries during cold crank- ing.
Manual Compass Calibration If the compass appears erratic and the “CAL” message does not appear in the EVIC display , you must put the compass into the Calibration Mode manually as follows: 1. T urn the ignition switch to the ON/RUN position. 2. Press the Menu button until Personal Settings is displayed.
1. T urn the ignition switch to the ON/RUN position. 2. Press the Menu button until Personal Settings is displayed. 3. Press the STEP button until “Compass V ariance” is displayed. 4. Press and release RESET button until the proper variance zone is selected according to the map.
The HomeLink t buttons are located in the over head console, and contain one, two, or three dots/lines desig- nating the differ ent HomeLink t channels. NOTE: HomeLink t is disabled when the V ehicle Secu- rity Alarm is active. W ARNING! Y our motorized door or gate will open and close while you are training the Universal T ransceiver .
W ARNING! V ehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run your vehicle in the garage while training the transceiver . Exhaust gas can cause seri- ous injury or death. Programming HomeLink T Before Y ou Begin If you have not trained any of the HomeLink t buttons, erase all channels before you begin training.
Then release both the HomeLink t and hand-held trans- mitter buttons. If the EVIC display states “DID NOT TRAIN” repeat Step 3. If the signal is too weak, replace the battery in the original hand-held transmitter . It may take up to 30 seconds, or longer , in rare cases.
6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer . NOTE: There ar e 30 seconds in which to initiate the next step after the “Learn” button has been pressed.
Similar to this Canadian law , some U.S. gate operators are designed to “time-out” in the same manner . It may be helpful to unplug the device during the cycling process to pr event possible overheating of the garage door or gate motor .
3. W ithout releasing the button, proceed with Program- ming HomeLink t Step 2 and follow all remaining steps. Security It is advised to erase all channels before you sell or turn in your vehicle. T o do this, press and hold the two outside buttons for 20 seconds until the EVIC message states “CHANNELS CLEARED.
NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly appr oved by the party responsible for compli- ance could void the user ’s authority to operate the device.
Open Sunroof - Express Mode Momentarily pressing the switch r earward will activate the Express Open Featur e, causing the sunroof to open automatically . During the Express Open operation, any movement of the switch will stop the sunroof and it will remain in a partial open position.
V enting Sunroof - Express Press and r elease the 9 V 9 button, and the sunroof will open to the vent position. This is called Express V ent, and will occur regar dless of sunroof position. During Express V ent operation, any movement of the switch will stop the sunroof.
There is an additional power outlet inside the center console of vehicles equipped with 40-20-40, or Bucket front seats. Ther e is also a power outlet located on the rear of the center console for Quad Cab t or Mega Cab t vehicles (only) equipped with bucket seats.
CIGAR LIGHTER AND ASH RECEIVER The removable ash r eceiver is located in the instrument panel cupholder tray . The cigar lighter is located on the instrument panel, above and to the left of the ash receiver . As a child safety precaution, the lighter only operates with the ignition switch ON.
CUPHOLDERS Front Instrument Panel Cupholders (40–20–40 Seats) — Automatic T ransmission Y our new vehicle is equipped with two adjustable cup- holders. The cupholder is opened by pulling on the cup holder door handle located on the front surface.
Cupholder Door Handle Cupholders Automatic T ransmission 164 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
Front Instrument Panel Cupholders (Bucket Seats) — Automatic T ransmission If your new vehicle is equipped with bucket seats there are thr ee cupholders located on the front of the center console.
Rear Cupholder (Quad Cab T ) — If Equipped Quad Cab t vehicles may be equipped with a rear cup- holder that consists of two cup wells for rear passenger convenience. Rear Cupholder (Mega Cab T ) Mega Cab t vehicles are equipped with r ear cupholders located in the center armrest.
STORAGE Center Storage Compartment (40–20–40 Seat) – If Equipped The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid.
CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.e., cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
storage area into separate compartments. Lift the lower handle on the front of the armr est, and raise the armrest for access to the lower storage bin. On Quad Cab t and Mega Cab t models the rear of the floor console of fers a power outlet, a tip out bin and a rear air duct (Mega Cab t Only).
Storage and Seats (Quad Cab T Models) Located in the center of the front 40–20–40 seat cushion there is a storage compartment. Regular Cab models also have storage behind the seat. The Quad Cab t models provide additional storage under the rear seat.
Storage and Seats (Mega Cab Models) The Mega Cab models provide additional storage behind the rear seat. T o gain access to the Mega Cab rear storage, fold the r ear seats to the “kneel position”. (See page 123 for more information.) Push down on the front of the storage compartment handle and lift the storage compartment cover .
The rear storage compartment can be divided into thr ee separate compartments by using the divider doors inside the storage compartment. Plastic Grocery Bag Retainers (Mega Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat.
REAR WINDOW FEA TURES Electric Rear Window Defroster and Heated Sideview Mirrors — If Equipped The Electric Rear W indow Defroster and Heated Sideview Mirrors ar e activated by pressing the heated grid button, located on the Climate Control panel, with the ignition ON.
Sliding Rear Window — If Equipped A locking device in the center of the window helps to prevent entry fr om the rear of the vehicle. Squeeze the lock to release the window . FOLD FLA T LOAD FLOOR — IF EQUIPPED Quad Cab t models with a 60/40 rear seat may be equipped with a folding load floor .
W ARNING! Do not operate the vehicle with loose items stored on the load floor . While driving or in an accident you may experience abrupt stopping, rapid acceleration, or sharp turns. Loose objects stored on the load floor may move around with force and strike occupants, resulting in serious or fatal injury .
2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. 3. Reverse the procedure to stor e the load floor . Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position.
4. Reverse the procedure to put the load floor back in the secured down position befor e you operate the vehicle. PICKUP BOX The pickup box on your new vehicle has many features designed for utility and convenience.
NOTE: If you are installing a toolbox to the fr ont of the pickup box, you must use Mopar t toolbox brackets available from your authorized dealer . Y ou can carry wide building materials (sheets of ply- wood, etc.
There ar e stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards acr oss the box from side to side to create separate load compartments in the pickup box.
NOTE: Dual rear wheel pickup models r equire properly spaced rear clearance lights. If such a vehicle is operated without a tailgate, suitable lights must be installed.
W ARNING! T o avoid inhaling carbon monoxide, which is deadly , the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks.
.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS m Instruments And Controls ................. 1 8 7 m Instrument Cluster ...................... 1 8 8 ▫ Instrument Cluster – 6.7L Diesel Engine ..... 1 8 8 m Instrument Cluster Description ............
▫ Operating Instructions - Hands-Fr ee Phone — If Equipped ........................... 2 0 9 ▫ Operating Instructions - Satellite Radio — If Equipped ........................... 2 0 9 m Sales Code RAQ – AM/FM/CD (6-Disc) Radio W ith Optional Satellite Radio, Hands-Free Phone, And V ideo Entertainment Systems (VES™) Capabilities .
▫ Noise Reduction ...................... 2 3 0 ▫ Operating Instructions - (CD Mode For CD Audio Play) ......................... 2 3 0 ▫ Load/Eject Button (CD Mode For CD Audio Play) .............................. 2 3 1 ▫ Notes On Playing MP3 Files .
▫ Satellite Antenna ...................... 2 4 5 ▫ Reception Quality ..................... 2 4 5 m Remote Sound System Controls — If Equipped . . 246 ▫ Radio Operation ...................... 2 4 6 ▫ T ape Player ......................... 2 4 7 ▫ CD Player .
INSTRUMENTS AND CONTROLS 1 — Headlight Switch 6 — Passenger Airbag* 1 1 — TPMS “Light Load” Reset Switch* 16 — T ransfer Case Control Switch* 2 — Air Outlets 7 — Glove Box 12 — Power.
INSTRUMENT CLUSTER Instrument Cluster – 6.7L Diesel Engine 188 UNDERST ANDING YOUR INSTRUMENT P ANEL.
INSTRUMENT CLUSTER DESCRIPTION 1. Check Gauges This light illuminates when the V oltmeter , Engine Oil Pressur e or Engine Coolant T emperature gauges indicate a reading either too high or too low . Examine the gauges carefully , and follow the instructions contained below for each indicated problem.
3. T urn Signal Indicators Lights in instrument cluster flash when outside turn signals are operating. 4. T achometer The tachometer indicates engine speed in revolutions per minute. CAUTION! Do not operate the engine with the tachometer pointer at high rpm for extended periods.
9. Oil Pressure Gauge The pointer should always indicate some oil pres- sure when the engine is r unning. A continuous high or low reading, under normal driving conditions, may indicate a lubrication system malfunction. Immedi- ate service should be obtained.
CAUTION! Do not leave your vehicle unattended with the en- gine running as you would not be able to react to the temperature indicator if the engine overheats. NOTE: Engine idle speed will automatically increase to 1000 rpm at elevated coolant temperatures to impr ove engine cooling.
during repair or r eplacement, be sure to keep a recor d of the reading befor e and after the service so that the correct mileage can be determined. The two trip odometers show individual trip mileage. T o switch from odometer to trip odometers, pr ess and release the T rip Odometer button.
17. Malfunction Indicator Light (MIL) This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
If the light remains on when the parking brake is released, it indicates a possible brake hydraulic system malfunction. In this case, the light will remain on until the cause is corrected. If brake failure is indicated, immediate r epair is necessary and continued operation of the vehicle in this condition is dangerous.
experience reduced performance, an elevated/r ough idle or engine stall and your vehicle may requir e towing. The light will come on when the ignition is first turned on and remain on for 15 seconds as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer .
As an added safety feature, your vehicle has been equipped with a tire pr essure monitoring system (TPMS) that illuminates a low tire pr essure telltale when one or more of your tir es is significantly under-inflated.
CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style.
Follow engine starting procedur e for proper engine start- ing and operating. W ait until the W ait T o Start indicator turns OFF , then start the vehicle. NOTE: The W ait T o Start Indicator may not illuminate if the engine coolant temperature is warm enough.
ELECTRONIC DIGIT AL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the fr equency and/or time in hours and minutes (depending on your radio model) whenever the ignition switch is in the ON or ACC position.
T wo T ypes of Signals There ar e two basic types of radio signals: AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary; and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound.
SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SA TELLITE RADIO AND HANDS FREE PHONE CAP ABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Mode Button (Radio Mode) Press the MODE button r epeatedly to select between the CD player and Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and r elease the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode.
Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the TUNE/AUDIO con- trol. 3. After the hours are adjusted, press the TUNE/AUDIO control to set the minutes. The minutes will begin to blink.
Press the r otary TUNE control a fourth time and BAL will display . T urn the TUNE control to the right or left to adjust the sound level from the right or left side speakers.
Operating Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player and the CD icon will illuminate on the radio display .
SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. T o stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal.
Operating Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player , cassette player , or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
TIME Button (Auxiliary Mode) Press this button to change the display fr om elapsed playing time to time of day . The time of day will display for five seconds.
SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SA TELLITE RADIO, HANDS-FREE PHONE, AND VIDEO ENTERT AINMENT SYSTEMS (VES™) CAP ABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate.
Mode Button (Radio Mode) Press the MODE button r epeatedly to select between the CD player , Satellite Radio, or V ideo Entertainment Sys- tem (VES)™ (if equipped). SEEK Button (Radio Mode) Press and r elease the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode.
TIME Button Press the TIME button and the time of day will be displayed for five seconds. Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the TUNE/AUDIO con- trol. 3. After the hours are adjusted, press the TUNE/AUDIO control to set the minutes.
Press the r otary TUNE control a second time and MID will display . T urn the TUNE control to the right or left to increase or decr ease the Mid Range tones. Press the r otary TUNE control a third time and TREBLE will display . T urn the TUNE control to the right or left to increase or decr ease the T reble tones.
T oggle the PTY button to select the following format types: Program T ype 16 Digit-Character Display No program type or undefined None Adult Hits Adult_Hits Alert Alert Alert Alert Classical Classica.
By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program T ype) mode, the PTY mode will be exited and the radio will tune to the preset station.
Operating Instructions - (CD Mode for CD Audio Play) NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: This Radio is capable of playing compact discs (CD), recor dable compact discs (CD-R), rewritable com- pact discs (CD-R W) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks.
SEEK Button (CD Mode for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the curr ent selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection.
Radio display will show 9 EJECTING DISC 9 when the disc is being ejected and prompt the user to r emove the disc. Press and hold the LOAD/ EJT button for five seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
RND/PTY Button (Random Play Button) (CD Mode for CD Audio Play) Press this button while the CD is playing to activate Random Play . This feature plays the selections on the compact disc in random order to pr ovide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
• Maximum number of characters in file/folder names: • Level 1: 12 (including a separator 9 . 9 and a 3-character extension) • Level 2: 31 (including a separator 9 . 9 and a 3-character extension) Multisession disc formats are supported by the radio.
Playlist files are not supported. MP3 Pr o files are not supported. Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
PLEASE W AIT and prompt when to INSER T DISC. After the radio displays 9 LOAD DISC 9 insert the CD into the player . Radio display will show 9 LOADING DISC 9 when the disc is loading.
TUNE Control (CD Mode for MP3 Play) Pressing the TUNE contr ol allows the adjustment of T one, Balance, and Fade. AM/FM Button (CD Mode for MP3 Play) Switches back to Radio mode. RND/ PTY Button (CD Mode for MP3 Play) Pressing this button plays files randomly .
SALES CODE RAK – AM/FM/CASSETTE/CD (6-DISC) RADIO WITH OPTIONAL SA TELLITE RADIO, HANDS FREE PHONE, VIDEO, MP3, and WMA CAP ABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
SEEK Button (Radio Mode) Press and r elease the SEEK button to search for the next station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remained tuned to the new station until you make another selection.
R W/FF (Radio Mode) Pressing the r ewind/fast forward button causes the tuner to search for the next fr equency in the direction of the arrows. This featur e operates in either AM, FM or Satel- lite (if equipped) frequencies. TUNE Control (Radio Mode) T urn the right side rotary contr ol to increase or decrease the frequency .
T urn the tune knob to select the following format types: Program T ype 16 Digit-Character Display No program type or un- defined None News News Information Information Sports Sports T alk T alk Rock .
By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program T ype) mode, the PTY mode will be exited and the radio will tune to the preset station.
Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing. The tape will advance until the button is pressed again or the end of the tape is reached. At the end of the tape, the tape will play in the opposite direction.
Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched off. T o turn off the Dolby Noise Reduction System: Pr ess Preset 1 after you insert the tape. The NR light in the display will go off when the Dolby System is of f.
If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the disc number , the track number , and index time in minutes and seconds. Play will begin at the start of track one.
Radio display will show 9 EJECTING DISC 9 when the disc is being ejected and prompt the user to r emove the disc. Press and hold the LOAD/EJT button for five seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
RND/PTY Button (Random Play Button) (CD Mode for CD Audio Play) Press this button while the CD is playing to activate Random play . This feature plays the selections on the compact disc in random order to pr ovide an interesting change of pace. NOTE: MP3 and WMA Random play are for file folders only .
The radio uses the following limits for file systems: • Maximum number of directory levels: 15 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator 9 .
MPEG Specification Sampling Fre- quency (kHz) Bit rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 1 12, 96, 80, 64, 56, 48, 40, 32 MPEG-2 Audio Layer 3 24, 22.
Operating Instructions - (CD Mode for MP3 and WMA Audio Play) SEEK Button (CD Mode for MP3 and WMA Play) Pressing the right side of the SEEK button plays the next file. Pressing the left side of the SEEK button plays the beginning of the file. Pressing the button within the first 10 seconds plays the previous file.
INFO Button (CD Mode for MP3 Play) Press the INFO button while playing MP3 or WMA disc. The radio scrolls thr ough the following T AG information: Song T itle, Artist, File Name, and Folder Name (if avail- able). Press the INFO button once mor e to return to 9 elapsed time 9 priority mode.
Operating Instructions - Hands Free Phone (If Equipped) Refer to “Hands-Free Phone” in Section 3 of the Owner’s Manual. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the “Satellite Radio” section of the Owner’s Manual.
menus and instructions for selecting a variety of destina- tions and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability . Mapping information for navigation is supplied on a DVD that is loaded into the unit. One map DVD covers all of North America.
2. T o show the GPS clock, select “Displayed Clock: GPS Clock” and press ENTER. 3. T o adjust the time zone, Select “T ime Zone” and press ENTER. Select the appropriate time zone and pr ess ENTER. 4. T o turn daylight savings on or off, select “Daylight Savings” and press ENTER.
3. T o decrease the clock by one hour , use the Select Encoder to highlight the “-” sign. Press ENTER. Pr ess ENTER again to decrease the clock by another hour . 4. T o increase the clock by minutes, make sure “MIN +” is highlighted and press ENTER.
System Activation Sirius Satellite Radio service is pre-activated, and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle.
when any other button is pushed, the ignition is turned OFF , or five minutes have passed since any button was pushed. ESN/SID Access with REC Navigation Radios Please refer to your Navigation User’s Manual.
Press and r elease the SCAN button (if equipped) to automatically change channels every seven seconds. The radio will pause on each channel for seven seconds before moving on to the next channel. The wor d 9 SCAN 9 will appear in the display between each channel change.
PTY Button SEEK When the desired pr ogram is obtained, press the SEEK button within five seconds. The channel will change to the next channel that matches the program type selected. Satellite Antenna T o ensure optimum r eception on vehicles available with a luggage rack, do not place items on the roof ar ound the rooftop antenna location.
REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system contr ols are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a r ocker type switch with a button in the center .
T ape Player Pressing the top of the switch once will go to the next selection on the cassette. Pressing the bottom of the switch once will go to the beginning of the current selection or to the beginning of the previous selection if it is within the first five seconds of the current selection.
5. A loose tape should be corrected befor e use. T o rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the requir ed direction. Maintain your cassette tape player . The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged, oversized, or have theft protection encoding. T ry a known good disc before considering disc player service.
Heater Only — If Equipped The mode control (at the right of the control panel) can be set in any of the following positions: NOTE: T o improve your selection choices, the system allows you to operate at intermediate positions between the major modes.
Recirculation Modes (Panel or Bi-Level) Select the recir culation modes when the outside air contains smoke or odors. This feature allows for r ecircu- lation of interior air only .
Air Conditioning and Heating — If Equipped Air Conditioning Operation T o turn on the Air Conditioning, set the fan control at any speed and pr ess the snowflake button located at the right of the control panel. Conditioned air will be directed thr ough the outlets selected by the mode control.
NOTE: T o improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots.
the windshield, and the demister outlets located at the edge of each side of the instrument panel, and the air conditioning may be on. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes, even if the A/C button has not been pr essed.
Side window demisters direct airflow specifically to the window glass to help prevent interior fogging of the glass. They are located in the extr eme outside upper edges of the instrument panel. The demisters also pr o- vide extra air ducts for circulation.
Air Conditioning and Heating Operation T o turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located on the control panel. Conditioned air will be dir ected through the outlets selected by the mode control. A light in the snowflake button shows that the air conditioning is on.
NOTE: T o improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots and give an even blend of both modes. Panel Outside air flows through the outlets located in the instrument panel.
Blower Control The rotary knob on the left of the control panel is the blower contr ol. T urn the knob clockwise to one of the four positions to obtain the blower speed you desire.
Circulation The cab is designed with features to pr omote outside air circulation. Ther e are grilles in the cab back panel. These are air exhausters that pr ovide the means for regular exchange of cab air . Side window demisters direct airflow specifically to the window glass to help prevent interior fogging of the glass.
Operating Tips Fast Cooldown For a fast cooldown, turn the blower fan rotary knob to the extreme right position, turn the mode contr ol to the panel fresh position, pr ess the snowflake button to turn on the air conditioning, and drive with the windows open for the first few minutes.
Summer Operation Air conditioned vehicles must be protected with a high quality antifreeze coolant during summer to pr ovide proper corr osion protection and to raise the boiling point of the coolant for protection against over heating. A 50 % concentration is recommended.
Operating Tips Chart 262 UNDERST ANDING YOUR INSTRUMENT P ANEL.
ST ARTING AND OPERA TING CONTENTS m Starting Procedur es – Diesel Engines ......... 2 6 8 ▫ Automatic T ransmission – If Equipped ...... 2 6 8 ▫ Manual T ransmission – If Equipped ........ 2 6 9 ▫ Normal Starting Procedur e – Engine Manifold Air T emperature Above 66°F (19°C) .
m Manual T ransmission .................... 2 9 1 ▫ Shifting ............................ 2 9 1 ▫ Downshifting ........................ 2 9 3 ▫ Reverse Shifting ...................... 2 9 4 m Four–Wheel Drive Operation — If Equipped . . . 294 ▫ Manually Shifted T ransfer Case Operating Information/Precautions .
▫ T ire Identification Number (TIN) .......... 3 1 9 ▫ T ire Loading And T ire Pr essure ........... 3 2 0 m T ires — General Information ............... 3 2 4 ▫ T ire Pr essure ......................... 3 2 4 ▫ T ire Inflation Pr essures ..
m Fuel Requirements ...................... 3 4 8 ▫ Fuel Requirements (6.7L Diesel Engines) ..... 3 4 8 m Adding Fuel (Diesel Engines) .............. 3 4 9 ▫ Fuel Filler Cap (Gas Cap) ............... 3 5 0 ▫ Bulk Fuel Storage ....................
m Recreational T owing (Behind Motorhome, Etc.) . . 375 ▫ Recreational T owing – 2-Wheel Drive Models ............................ 3 7 5 ▫ Recreational T owing – 4-Wheel Drive Models .
ST ARTING PROCEDURES – DIESEL ENGINES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. The starter should not be operated for more than 15- second intervals. W aiting a few minutes between such intervals will protect the starter fr om overheating.
NOTE: The engine block heater cord is a factory in- stalled option. If your vehicle is not equipped, heater cords ar e available from your authorized Mopar t dealer . • A 12–volt heater built into the fuel filter housing aids in preventing fuel gelling.
CAUTION! If W A TER IN FUEL indicator light remains on DO NOT ST AR T engine before you drain water from the fuel filter to avoid engine damage. Refer to “Drain- ing Fuel/W ater Separator Filter (6.7L Diesel Engine)” under “Maintenance Procedures” in Section 7.
Follow the steps in the Normal Starting Procedur e ex- cept: CAUTION! Do not crank engine for more than 15 seconds at a time or starter motor damage may result. T urn key to OFF and wait at least two minutes for starter to cool before repeating start procedure.
For Extremely Cold W eather Starting — Engine Manifold Air T emperature Below 0°F (-18°C) In extremely cold weather below 0°F (-18°C) it may be beneficial to cycle the manifold heaters twice before attempting to start the engine.
• If the engine is started before the W AIT TO ST ART light turns off, the pr eheat cycle will turn off. • If the engine is cranked for more than 10 seconds, the post-heat cycle will turn off. NOTE: Engine idle speed will automatically increase to 1000 RPM at low coolant temperatures to impr ove engine warm-up.
Starting Fluids W ARNING! ST AR TING FLUIDS or flammable liquids are NEVER TO BE USED in the Cummins t Diesel (see W arning label). Never pour diesel fuel, flammable liquid, starting fluids (ether) into the air cleaner canister , air intake piping, or turbocharger inlet in an attempt to start the vehicle.
• V oltmeter Operation: 1. The voltmeter may show a gauge fluctuation if certain engine temperatures ar e below 66°F (19°C). This cycling operation is caused by the post-heat cycle of the intake manifold heater system. The number of cycles and the length of the cycling operation is controlled by the engine contr ol module.
• Climatized Ultra Low Sulfur Diesel Fuel is a blend of Number 2 Ultra Low Sulfur and Number 1 Ultra Low Sulfur Diesel Fuels which reduces the temperatur e at which wax crystals form in fuel. NOTE: The engine requir es the use of “Ultra Low Sulfur Diesel Fuel” .
Block Heater Usage A. T emperatures below 0°F (-18°C) • Block Heater Required for 15W -40 • Block Heater Recommended for 5W -40 B. T emperatures below - 20°F (-29°C) • Block Heater Required .
NOTE: High-speed, no-load running of a cold engine can result in excessive white smoke and poor engine performance. No-load engine speeds should be kept under 1,200 rpm during the warm-up period, especially in cold ambient temperature conditions.
NOTE: An optional driver-contr olled high idle speed is available on automatic transmission equipped vehicles with speed control. This featur e allows the driver to select an elevated idle speed between 1 100 and 1500 rpms. Y our dealer can enable this feature.
Stopping The Engine Idle the engine a few minutes before r outine shutdown. After full load operation, idle the engine 3 to 5 minutes before shutting it down. This idle period will allow the lubricating oil and coolant to carry excess heat away from the combustion chamber , bearings, internal components, and turbocharger .
Engine Speed Control CAUTION! Prevent overspeeding the engine going down hill. When descending steep grades, use a combination of gears and service brakes to control vehicle/engine speed.
• Up Steep Hills — select a lower transmission gear , but try and keep the torque converter clutch engaged. • Air Conditioning — turn it off temporarily . Do Not Operate The Engine W ith Low Oil Pressure When the engine is at normal operating temperature, the minimum oil pressur es required ar e: Idle 700 to 800 RPM .
DIESEL EXHAUST BRAKE (ENGINE BRAKING) – IF EQUIPPED The exhaust brake feature will only function when the driver turns the exhaust brake switch to the ON position.
W ARNING! Do not use the Exhaust Brake feature when driving in icy or slippery conditions as the increased engine braking can cause the rear wheels to slide and the vehicle to swing around with the possible loss of vehicle control, which may cause an accident possi- bly resulting in personal injury or death.
TRANSMISSION SHIFTING Automatic T ransmission with Overdrive (68RFE) — If Equipped The gear selector lever display located in the instrument panel cluster indicates the transmission gear range (the selector is illuminated for night driving). The selector lever is mounted on the right side of the steering column.
W ARNING! Y our vehicle could move and injure you and others if it is not completely in P ARK. Check by trying to move the shift lever back and forth without first pulling it toward you after you have set it in P ARK. Make sure it is in P ARK before leaving the vehicle.
Upshifts into both overdrive gears, 5th and 6th, will be delayed when the transmission fluid temperature is below 40° F (4.5° C) or above 240° F (1 15.5° C). NOTE: Use caution when operating a heavily loaded vehicle in 2nd or 1st gear in high ambients as torque converter slip can impose significant additional heat load on the cooling system.
NOTE: If the vehicle is started in extremely cold tem- peratures, the transmission may not shift into Over drive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperatur e has risen to a suitable level.
delayed. Shifts into 5th and 6th gear are still allowed under steady cruise conditions. Closed thr ottle down- shifts (for improved engine braking) may occur during steady braking maneuvers. Pressing the switch a second time restor es normal operation.
NOTE: T o select the proper gear position for maximum deceleration (engine braking), simply press and hold the switch down (-). The transmission will shift to the range from which the vehicle can best be slowed down. T orque Converter Clutch A feature designed to improve fuel economy has been included in the automatic transmission on your vehicle.
MANUAL TRANSMISSION W ARNING! Y ou or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should al- ways be applied when the driver is not in the vehicle, especially on an incline.
T ruck models with manual transmission are equipped with a clutch interlocking ignition system. The clutch pedal must be fully depressed to start the vehicle. Fully depress the clutch pedal befor e shifting gears. As you release the clutch pedal, lightly depr ess the accelera- tor pedal.
Downshifting Moving from a high gear down to a lower gear is recommended to pr eserve brakes when driving down steep hills. In addition, downshifting at the right time provides better acceleration when you desir e to resume speed. Downshift progr essively .
Maximum Recommended Downshifting Speeds Gear Selec- tion 6t o5 5t o4 4t o3 3t o2 2t oL Maxi- mum Speed 68 mph (109 km/h) 50 mph (80 km/h) 32 mph (51 km/h) 19 mph (31 km/h) 10 mph (16 km/h) Reverse Shifting T o shift into REVERSE (R), bring the vehicle to a com- plete stop.
This transfer case is intended to be driven in the 2-wheel drive position (2H) for normal street and highway con- ditions such as dry hard surfaced r oads.
NOTE: Delayed shifts out of four-wheel drive may be experienced due to uneven tire wear , low or uneven tire pressur es, excessive vehicle loading, or cold tempera- tures. W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake.
4L 4-Wheel Drive Low Range - Low speed 4-wheel drive. Locks the front and r ear driveshafts together . Forces the front and r ear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only .
vehicle in motion, the transfer case will engage/ disengage faster if you momentarily release the accelera- tor pedal after completing the shift. Apply a constant force when shifting the transfer case lever .
Electronically Shifted T ransfer Case Operating Information/Precautions (4 Position Switch) — If Equipped This is an electric shift transfer case and is operated by the 4WD Control Switch (T ransfer Case Switch), which is located on the instrument panel.
in the 4WD LOCK and 4WD LOW positions on dry hard surfaced roads may cause incr eased tire wear and dam- age to the driveline components. NOTE: The transfer case NEUTRAL position is selected by depressing the r ecessed button located on the lower left hand corner of the 4WD Control Switch.
If One or More Shift Conditions Are Not Met: 1. The indicator light for the current position will remain ON. 2. The newly selected position indicator light will con- tinue to flash.
When operating your vehicle in 4WD LOW , the engine speed is approximately thr ee times that of the 2WD or 4WD LOCK positions at a given road speed. T ake care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of 4-wheel drive vehicles depends on tires of equal size, type and cir cumference on each wheel.
4WD LOCK 4-Wheel Drive Lock Range - Locks the front and r ear driveshafts together . Forces the front and r ear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only . 4WD LOW 4-Wheel Drive Low Range - Low speed 4-wheel drive.
light will continue to flash until all the requir ements for the selected position have been met. T o retry a shift: return the contr ol knob back to the original position, make certain all shift requir ements have been met, wait five seconds and try the shift again.
Preferred Procedure 1. W ith engine running, slow vehicle to 2 to 3 mph (3 to 5 km/h). 2. Shift the transmission into NEUTRAL (depr ess clutch on manual transmissions). 3. While still rolling, rotate the transfer case contr ol switch to the desired position.
LIMITED-SLIP DIFFERENTIAL — IF EQUIPPED The limited-slip differ ential provides additional traction on snow , ice, mud, sand and gravel, particularly when there is a dif ference between the traction characteristics of the surface under the right and left rear wheels.
DRIVING ON SLIPPER Y SURF ACES When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and r oad surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability .
Shallow Standing W ater Although your vehicle is capable of driving through shallow standing water , consider the following Caution and W arning before doing so.
W ARNING! • Driving through standing water limits your vehi- cle’ s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water . • Driving through standing water limits your vehi- cle’ s braking capabilities, which increases stop- ping distances.
NOTE: After off-r oad usage, particularly in sand or mud, inspect the underside of the vehicle for accumu- lated dirt at the propeller shaft, axles, U-joints, brake rotors and calipers. Use a hose to clean off any accumulation of dirt or mud. Check the exhaust system and all exposed components for any sign of damage.
Be sure the parking brake is firmly set when parked and the shift lever is in the P ARK position. When parking on a hill you should apply the parking brake before placing the shift lever in P ARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of P ARK.
When parking on a hill, turn the front wheels towar d the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle.
Four-Wheel Anti-Lock Brake System W ARNING! Anti-Lock Brake Systems contain sophisticated elec- tronic equipment. It may be susceptible to interfer- ence caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability .
This Anti-lock Brake System is designed to aid the driver in maintaining vehicle control under adverse braking conditions. The system operates with a separate com- puter to modulate hydraulic pressur e to prevent wheel lockup and help avoid skidding on slippery surfaces.
POWER STEERING The standard power steering system will give you good vehicle response and incr eased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interr upted, it will still be possible to steer your vehicle.
TIRE SAFETY INFORMA TION Tire Markings NOTE: • P (Passenger)-Metric tir e sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tir e sizing is based on European design standards.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger Car tire size based on U.S. design standar ds ( ....blank.... ( = Passenger Car tire based on Eur opean design standards LT = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can ca.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however , the date code may only be on one side. T ires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressure is listed on either the face of the driver’s door or the driver’s side B-Pillar .
Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loadi.
available cargo and luggage load capacity is 650 lbs (295 kg) {(since 5 x 150 = 750, and 1400 – 750 = 650 lbs (295 kg)}. 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.
ST ARTING AND OPERA TING 323 5.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Under-inflation also increases tire r olling resistance and results in higher fuel consump- tion.
check tire pr essure. Do not make a visual judgement when determining proper inflation. Radial tir es may look properly inflated even when they ar e under-inflated. CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped).
T ire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tir e inflation pressure is very important.
Compact Spare Tire — If Equipped The compact spare is for temporary emer gency use with radial tires. It is engineer ed to be used on your style vehicle only . Since this tire has limited tread life, the original tire should be r epaired (or replaced) and r ein- stalled at the first opportunity .
original equipped tire on the fr ont or rear axle of your vehicle, but it is not. Installation of this limited-use spare tire af fects vehicle handling. Since it is not the same tire, replace (or r epair) the original tire and reinstall on the vehicle at the first opportunity .
T read Wear Indicators T read wear indicators ar e in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tr ead grooves. They will appear as bands when the tr ead depth becomes 1/16 in (2 mm).
W ARNING! T ires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. Y ou could lose control and have an accident resulting in serious injury or death.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, result- ing in changes to steering, handling, and braking of your vehicle.
Improper alignment will not cause vehicle vibration. V ibration may be a result of tir e and wheel out-of- balance. Proper balancing will r educe vibration and avoid tire cupping and spotty wear .
These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. T ire chain use is permitted only on the r ear tires of Ram 4X2 trucks. NOTE: The use of class “U” chains is permitted on the front and r ear of 4X4, 2500 Ram T rucks with L T245/ 70R17E tires.
SNOW TIRES Snow tires should be of the same size and type constr uc- tion as the front tir es. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requir ement associated with the tire. These tires should always be operated at the vehicle maximum capacity inflation pressur es under any load condition.
Follow the recommended tir e rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More fr equent rotation is permis- sible if desired. The r easons for any rapid or unusual wear should be corrected prior to r otation being per- formed.
Dual Rear Wheels The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tir e in a set. T o check if tires ar e even, lay a straight edge across all four tires. The straight edge should touch all the tir es. CAUTION! 3500 Dual Rear T ires have only one approved direc- tion of rotation.
TIRE PRESSURE MONITOR SYSTEM (TPMS) — IF EQUIPPED The T ire Pr essure Monitoring System (TPMS) will warn the driver of a low tire pr essure based on the vehicle recommended cold tir e inflation placard pressur e. The placard pr essure is defined on the T ire and Loading Information label.
The TPM System will continue to warn the driver of low tire pr essure as long as the condition exists, and will not turn off until the tir e pressure is at or above r ecom- mended cold placard pr essure.
CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap. This will prevent mois- ture and dirt from entering the valve stem, which could damage the T ire Pressure Monitoring Sensor .
Tire Pressure Monitor System (TPMS) “Light Load” Reset Switch Description – If Equipped W ARNING! Never operate your vehicle with the TPMS and tire pressures set to the Light Load Inflation Pressure settings if carrying more than two occupants (150 lbs each) plus 200 pounds of cargo.
“Light Load” Reset Switch Operation – If Equipped • This vehicle may have differ ent recommended tire pressur e values between the front and rear tir es as shown in both the T ire Loading Information Label and the Supplemental T ire Pr essure Information Label.
T o switch from the max load inflation pr essure (cold) low pressur e warning threshold to the light load inflation pressur e (cold) low pressure warning thr eshold, begin by placing the ignition switch in the RUN position.
W ARNING! It is the driver ’ s responsibility to change to the max load inflation pressure (cold) low pressure warning threshold condition when not driving in the light load condition as defined as two occupants ( 150 lbs each) plus 200 pounds of cargo.
NOTE: It is particularly important, for you to check the tire pr essure in all of your tires r egularly and to maintain the proper pr essure. The T ire Pr essure Monitoring System (TPMS) consists of t.
the ignition key is cycled, this sequence will repeat, providing the system fault still exists. A system fault can occur by any of the following scenarios: 1. Signal interference due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPM sensors.
Light will turn OFF , as long as no tire pr essure is below the low-pressur e warning limit in any of the four active road tir es. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information.
FUEL REQUIREMENTS Fuel Requirements (6.7L Diesel Engines) Use good quality diesel fuel from a r eputable supplier in your vehicle. Federal law requir es that you must fuel this vehicle with Ultra Low .
Fuel Specifications The Cummins T urbocharged, Char ge Air Cooled, Diesel engine has been developed to take advantage of the high energy content and generally lower cost No. 2 Ultra Low Sulfur diesel fuel or No. 2 Ultra Low Sulfur climatized diesel fuels.
W ARNING! A fire may result if fuel is pumped into a portable container that is on a truck bed. Y ou could be burned. Always place fuel containers on the ground while filling. Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door . If the gas cap is lost or damaged, be sure the r eplacement cap is for use with this vehicle.
A void Using Contaminated Fuel Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system. Pr oper main- tenance of the engine fuel filter and fuel tank is essential.
2. Crank the engine for 1 to 2 seconds. If the engine does not start, then release the key or starter button back to the RUN position (do not turn the key back to the OFF position). The electric fuel transfer pump will continue to run and pur ge air from the system for about 20 seconds.
Gross V ehicle W eight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver , passengers, vehicle, options and cargo. The label also specifies maximum capacities of front and rear axle systems (GA WR). T otal load must be limited so GVWR and front and r ear GA WR are not exceeded.
Curb W eight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.
An EXAMPLE of a loaded vehicle is shown in the following chart. Note that neither GVWR nor GA WR capabilities are exceeded. Overloading can cause poten- tial safety hazards and shorten service life. NOTE: The weights shown in this chart are not necessarily the weights for your vehicle.
TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer car efully re- view this information to tow your load as efficiently and safely as possible.
Gross Axle W eight Rating (GA WR) The GA WR is the maximum capacity of the front and rear axles. Distribute the load over the front and r ear axles evenly . Make sure that you do not exceed either front or rear GA WR. W ARNING! It is important that you do not exceed the maximum front or rear GA WR.
W eight-Distributing Hitch A weight-distributing system works by applying lever- age through spring (load) bars. They ar e typically used for heavier loads, to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s).
W eight-Distributing Hitch System Improper Adjustment Of W eight-Distributing System ST ARTING AND OPERA TING 359 5.
Fifth-Wheel Hitch A special high platform with a coupling that mounts over the rear axle of the tow vehicle in the tr uck bed. Connects a vehicle and fifth-wheel trailer with a coupling king pin. Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck.
T railer T owing Weights (Maximum T railer Weight Ratings) NOTE: For additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: • http:// www .dodge.com/towing . • http:// www .dodge.ca (Canada).
• The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
W ARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
2. GTW 3. GA WR 4. T ongue weight rating for the trailer hitch utilized (This requir ement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). T owing Requirements — T ires − Do not attempt to tow a trailer while using a compact spare tir e.
− An electronically actuated trailer brake contr oller is requir ed when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electr onic brake controller is not r equired.
The T railer T ow Package may includ ea4a n d7p i n wiring harness. Use a factory approved trailer harness and connector . NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector .
W ARNING! Any work done to the vehicles electrical system, or wiring, should be performed by a qualified automo- tive technician, if done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury .
T railer T ow Additional Lamp Loads Output Functions Maximum Current Additional Bulbs Allowed Example Only . Other bulb combinations can be used as long as maximum cur- rent is not ex- ceeded.
The automatic transmission fluid and filter should be changed if you REGULARL Y tow a trailer for mor e than 45 minutes of continuous operation. See Maintenance Schedule in section 8 of this manual for transmission fluid change intervals. NOTE: Check the automatic transmission fluid level before towing.
− refer to Cooling System Operating information in the Maintenance section of this manual for more informa- tion. T railer T owing Mirrors — If Equipped These mirrors ar e designed with an adjustable mirror head to provide a gr eater vision range when towing extra-wide loads.
SNOWPLOW Snowplow Prep Packages ar e available as a factory installed option. These packages include components necessary to equip your vehicle with a snowplow .
Before plowing • Check the hydraulic system for leaks and proper fluid level. • Check the mounting bolts and nuts for proper tight- ness. • Check the runners and cutting edge for excessive wear . The cutting edge should be 1/4 to 1/2 inch above ground in snow plowing position.
of the plow . Front end tow-in should be checked and reset if necessary at the beginning and end of the snowplow season. This will help prevent uneven tir e wear .
NOTE: During snowplow usage on vehicles equipped with an overhead console module, the outside tempera- ture display will show higher temperatur es than the outside ambient temperature. The higher displayed tem- perature is due to blocked or r educed airflow to the underhood ambient temperatur e sensor by the snow- plow .
RECREA TIONAL TOWING (BEHIND MOTORHOME, ETC.) CAUTION! Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. Recreational T owing – 2-Wheel Drive Models Recreational towing of 2-Wheel Drive models is not allowed.
Recreational T owing Procedure — Manual Shift T ransfer Case — If Equipped Use the following procedur e to prepare your vehicle for recr eational towing: CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL before recre- ational towing to prevent damage to internal parts.
CAUTION! Damage to the automatic transmission may occur if the transmission is shifted into P ARK with the trans- fer case in NEUTRAL and the engine running. W ith the transfer case in NEUTRAL ensure that the engine is OFF prior to shifting the transmission into P ARK.
CAUTION! • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage the internal parts.
7. After shift is completed and the NEUTRAL light comes on, release the NEUTRAL button. 8. Start engine. 9. Shift automatic transmission into REVERSE. 10. Release brake pedal for five seconds and ensure that there is no vehicle movement. 1 1. Repeat steps 9 and 10 with the transmission in DRIVE.
CAUTION! Damage to the transmission may occur if the trans- mission is shifted into P ARK with the transfer case in NEUTRAL and the engine running. W ith the transfer case in NEUTRAL ensure, that the engine is OFF prior to shifting the transmission into P ARK.
NOTE: Steps 1 through 5 ar e requirements that must be met prior to depressing the transfer case Neutral (N) button, and must continue to be met until one second elapses and the shift has been completed.
W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake. The transfer case NEUTRAL position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move despite the transmission position.
WHA T T O DO IN EMERGENCIES CONTENTS m Hazard W arning Flasher .................. 3 8 4 m Jacking And T ire Changing ................ 3 8 5 ▫ All Models – If Equipped ............... 3 8 5 m Jacking Instructions ..................... 3 8 6 ▫ Removing The Spare T ire .
HAZARD W ARNING FLASHER The Hazard W arning switch is mounted on the top of the steering column as shown in the illustration. T o engage the Hazard W arning lights, depress the button on the top of the steering column.
JACKING AND TIRE CHANGING W ARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
W ARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience, abrupt stopping, rapid accelera- tion, or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury .
NOTE: The winch mechanism is designed for use with the jack extension tube only . Use of an air wrench or other power tools is not recommended and can damage the winch. Tire Changing Procedure W ARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you.
• T urn on the Hazard W arning Flasher . • Block both the front and r ear of the wheel diagonally oppo- site the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked.
1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3. For 2500/3500 4x2 series trucks, when changing a front wheel, place the bottle jack under the frame rail behind the wheel.
NOTE: If the jack will not lower by turning the dial (thumbwheel) by hand, it may be necessary to use the jack drive tube in order to lower the jack. 4X2 Jacking 390 WHA T TO DO IN EMERGENCIES.
4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. W ARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it.
6. Using the wheel wrench, finish tightening the nuts using a crisscross pattern. Corr ect nut tightness is 135 ft. lbs. (183 N·m) torque for 2500/3500 single r ear wheel (SR W) models and 145 ft.
On 3500 models with dual rear wheels (DR W), you must first remove the hub caps. The jack handle driver has a hook at one end that will fit in the pry off notch of the rear hub caps. Position the hook and pull out on the ratchet firmly . The hub cap should pop off.
8-Stud — Dual Rear Wheels Dual wheels are flat mounted, center piloted. The lug nuts are a two piece assembly . When the tires ar e being rotated or r eplaced, clean these lug nuts and add two drops of oil at the interface between the hex and the washer .
These dual rear wheels should be tightened as follows: 1. T ighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go thr ough the sequence a second time to verify that specific torque has been achieved.
tightened to recommended tor que. T ighten the nuts to final torque in incr ements. Progress ar ound the bolt circle, tightening the nut opposite to the nut just pr evi- ously tightened until final torque is achieved. Recom- mended torques ar e shown in the following chart.
JUMP-ST ARTING W ARNING! T o prevent personal injury or damage to clothing, do not allow battery fluid to contact eyes, skin or fabrics. Do not lean over a battery when connecting jumper cables or allow cable clamps to touch each other . Keep open flames or sparks away from battery vent holes.
CAUTION! Use the Jump-Start Procedure only when the charge indicator (if equipped) in both batteries is dark in the center . Do not attempt jump-starting when either battery charge indicator (if equipped) is bright or yellow .
2. Connect one end of the other jumper cable to negative (-) post of booster battery . Connect the other end of the jumper cable to a good ground on the engine block of the vehicle with the discharged battery . Make sure a good connection is made, free of dirt and gr ease.
W ARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle.
In general, the least amount of accelerator pedal pressur e to maintain the rocking motion without spinning the wheels or racing the engine, is most effective. Racing the engine or spinning the wheels, due to the frustration of not freeing the vehicle, may lead to transmission over - heating and failure.
CAUTION! T ow hooks are for emergency use only , to rescue a vehicle stranded off-road. Do not use tow hooks for tow truck hookup or highway towing. Y ou could damage your vehicle. TOWING A DISABLED VEHICLE Proper towing or lifting equipment is r equired to prevent damage to your vehicle.
2–Wheel Drive V ehicles Provided that the transmission is operable, tow with the transmission in NEUTRAL and the ignition key in the OFF position along with the front wheels raised and the rear wheels on the gr ound. Speed must not exceed 30 mph (50 km/h) and distance must not exceed 15 mi (25 km).
.
MAINT AINING YOUR VEHICLE CONTENTS m Engine Compartment — 6.7L Diesel Engine .... 4 0 8 m Onboard Diagnostic System (OBD II) ......... 4 0 9 m Replacement Parts ...................... 4 0 9 m Engine Data Plate ...................... 4 1 0 m Authorized Dealer Service .
▫ Front Suspension Ball Joints .............. 4 3 1 ▫ Steering Linkage — Inspection ............ 4 3 2 ▫ Front Pr op Shaft Lubrication ............. 4 3 2 ▫ Front Axle Universal Drive Joints And Ball Joints .............................. 4 3 2 ▫ Body Lubrication .
m V ehicle Storage ........................ 4 6 4 m Replacement Light Bulbs ................. 4 6 5 m Bulb Replacement ...................... 4 6 6 ▫ Headlight (Halogen)/Front Park And T urn Lights ............................. 4 6 6 ▫ Fog Lights .
ENGINE COMP ARTMENT — 6.7L DIESEL ENGINE 408 MAINT AINING YOUR VEHICLE.
ONBOARD DIAGNOSTIC SYSTEM (OBD II) V ehicles equipped with California emissions controls have a sophisticated onboard diagnostic system called OBDII. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
ENGINE DA T A PLA TE Use the information from the engine data plate when discussing service or sourcing parts for your engine. The engine data plate is located on the intake side of the breather cover .
CAUTION! T o maintain your vehicle safely follow these guide- lines: • W atch your vehicle’s mileage and check your Maintenance Schedules regularly for required ser- vicing. Excessive wear or damage to certain vehicle components can result if required services are not performed.
W ARNING! T o maintain your vehicle safely and avoid personal injury , follow these guidelines: • Never spray or pour diesel fuel, flammable liquid or starting fluids (ether) into the air cleaner assembly , air intake piping or turbocharger inlet in an attempt to start the vehicle, unintended engine acceleration may occur .
Engine Oil Checking Oil Level T o assure pr oper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. Check the oil level at regular intervals. The best time to check the oil level is before starting the engine after it has been parked overnight.
Never operate the engine with oil level below the “ADD” mark or above the upper “SAFE” mark. Change Engine Oil (6.7L Diesel Engine) Follow the 6.7L Diesel Maintenance Schedule for recom- mended engine oil change intervals. Engine Oil Selection (6.
Engine Oil V iscosity (SAE Grade) Use SAE 15W -40 Engine Oil that meets DaimlerChrysler Materials Standard MS-10902 and the API CJ-4 engine oil category . Engine oil not designated by the DaimlerChrysler or Cummins t Material Standards and API CJ-4 should not be used, engine and exhaust system durability may be compromised.
Engine Oil Filter Refer to Fluids, Lubricants and Genuine Parts for the correct part number . The engine oil filter should be changed at every engine oil change. Engine Oil And Filter — Change Operate the engine until the coolant temperature r eaches 140°F (60°C).
CAUTION! Fill the oil filter element with clean oil before instal- lation. Use the same type oil that will be used in the engine. When filling the oil filter , prevent foreign material from falling into the filter .
Start the engine and operate it at idle for several minutes. Check for leaks at the lubricating oil filter and oil pan drain plug. Run the engine until it has reached operating tempera- ture, stop the engine. W ait approximately 15 minutes to let the oil in the upper parts of the engine drain back to the pan.
Engine Air Cleaner Filter (6.7L Diesel Engines) CAUTION! All air entering the engine intake must be filtered. The abrasive particles in unfiltered air will cause rapid wear to engine components. The condition of the air cleaner filter is monitored by the Engine Control Module.
If the vehicle experiences a sudden loss of engine power when being driven in heavy snow , rain or when plowing snow , and the EVIC message center states SER VICE AIR FIL TER or the Filter Minder™ (if equipped) is showing a plugged filter , then visually inspect the air filter for snow/ice build up or extreme water saturation.
The clear plastic housing on the Filter Minder™ (If Equipped), allows you to view the amount of air pressur e drop acr oss the filter element. It consists of a diaphragm and a calibrated spring sealed inside the plastic housing.
Draining Fuel/W ater Separator Filter (6.7L Diesel Engine) CAUTION! Do not drain the fuel/water separator filter when the engine is running. CAUTION! Do not prefill the fuel filter when installing a new fuel filter . There is a possibility that debris could be introduced into the fuel filter during this action.
If the W A TER IN FUEL LIGHT comes on and a single chime is heard while you ar e driving, or with the key in the ON position, there may be a pr oblem with your water separator wiring or sensor .
W ARNING! Do not open the high pressure fuel system with the engine running. Engine operation causes high fuel pressure. High pressure fuel spray can cause serious injury or death. Priming if the engine has run out of fuel 1. Add a substantial quantity of fuel to the tank, approxi- mately 5 to 10 gallons (19L to 38L).
W ARNING! Do not use alcohol or gasoline as a fuel blending agent. They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel. CAUTION! Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.
T o achieve these emission standards, your vehicle is equipped with a state of the art engine and exhaust system. The engine and exhaust aftertreatment system work together to achieve the EP A Heavy Duty Diesel Engine Emissions Standards. These systems ar e seam- lessly integrated into your vehicle and managed by the Cummins t 6.
located on the top of the engine valve cover . For addi- tional information, see your local authorized dealer . Catalyst Full See Owner Manual “Catalyst Full See Owner Manual” will be displayed on the overhead console of your vehicle if the exhaust particulate filter reaches 80% of its maximum storage capacity .
CA T AL YST FULL SER VICE REQD If the particulate filter reaches 99% of its capacity , the overhead console in your vehicle will chime twice and display the message CA T AL YST FULL SER VICE REQD.
W ARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water .
Battery Blanket Usage A battery loses 60% of its cranking power as the battery temperature decr eases to 0°F (-18°C). For the same de- crease in temperatur e, the engine requires twice as much power to crank at the same RPM. The use of 120 V AC powered battery blankets will gr eatly increase starting capability at low temperatures.
NOTE: Use only manufacturer appr oved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compr es- sor Oil, or Refrigerants. Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar - bon (HFC) that is endorsed by the Environmental Pr o- tection Agency and is an ozone-saving product.
Steering Linkage — Inspection Whenever the vehicle is hoisted all steering linkage joints should be inspected for evidence of damage. If seals are damaged, parts should be replaced to pr event leakage or contamination of the grease.
Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, liftgate, tailgate, sliding doors and hood hinges should be lubricated periodically to assure quiet, easy operation and to protect against r ust and wear .
Windshield W ashers The fluid reservoir is located under the hood and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent only (not ra- diator antifreeze). When r efilling the washer fluid reser- voir , take some washer fluid and apply it to a cloth or towel and wipe the wiper blades clean.
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, .
Cooling System W ARNING! Y ou or others can be badly burned by hot coolant or steam from your radiator . If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot.
Coolant bottle level check The coolant reserve system pr ovides a quick visual method of determining that the coolant level is adequate. W ith the engine idling and warmed to the normal operating temperature, the level of the coolant on the coolant bottle should be between the fluid level marks.
CAUTION! The manufacturer highly recommends that all cool- ing system service, maintenance, and repairs be per- formed by your local authorized dealer . If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner .
Adding Coolant Y our vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Y ears or 100,000 miles (160 000 km) before r eplacement. T o prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle.
The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. W ARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated.
The radiator normally remains completely full, so ther e is no need to remove the radiator cap unless checking for coolant freeze point or r eplacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory , the coolant bottle need only be checked once a month.
• Make sure that the radiator and coolant r ecovery bottle overflow hoses are not kinked or obstr ucted. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean also. • Do not change the thermostat for summer or winter operation.
T o guarantee optimum performance of the system, keep the surfaces of the charge air cooler , condenser and radiator clean and free of debris. Periodically check the hoses leading to and from the char ge air cooler for cracks or loose clamps resulting in loss of pr essure and reduced engine performance.
Brake Master Cylinder The fluid level of the master cylinder should be checked when performing under the hood service, or immedi- ately if the brake system warning lamp indicates system failure. The brake master cylinder has a translucent plastic reservoir .
W ARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from for eign matter or moisture.
Rear Axle And 4x4 Front Driving Axle Fluid Level For Model 9.25 Front Axles and 10.5”/1 1.5” Rear Axles refer to Fluids, Lubricants and Genuine Parts for the correct lubricant type. For normal service, periodic fluid level checks are not r equired.
Drain And Refill Follow the Maintenance Schedule for recommended transfer case fluid change intervals. Lubricant Selection Refer to Fluids, Lubricants and Genuine Parts for the correct lubricant type. Manual T ransmission — If Equipped Fluid Level Check This fluid level can be checked by removing the filler plug.
CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder . Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes.
5. Remove the dipstick, wipe it clean and reinsert it until seated. 6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be between the “HOT” (upper) refer ence holes on the dipstick at normal operat- ing temperature.
Automatic T ransmission Fluid and Filter Change T o obtain best performance and long life for automatic transmissions, the manufacturer r ecommends that they be given regular maintenance service by an authorized dealer or Service Center .
Rear Wheel Bearings Clean and repack when brake linings ar e replaced or rotors r esurfaced. Noise Control System Required Maintenance & W arranty For 3500 T wo-Wheel Drive and Four-Wheel Drive mod- els over 10,000 lbs. (4 535 kg) Gross V ehicle W eight Rating.
Required Maintenance For Noise Control Systems The following maintenance services must be performed every 6 months or 6,000 miles (9 600 km), whichever comes first, to assure pr oper operation of the noise control systems. In addition, inspection and service should be performed anytime a malfunction is observed or suspected.
Among those acts presumed to constitute tampering ar e the acts listed below . • AIR CLEANER − Removal of the air cleaner . − Removal of the air cleaner filter element from the air cleaner housing.
Maintenance Log and Service Chart (Diesel Engines) Noise Systems Maintenance Chart and Service Log — Insert Month, Day , Y ear under column mileage closest to the mileage at which service was performed.
Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion V ehicle body care requir ements vary according to geo- graphic locations and usage.
• A void using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder which will scratch metal and painted surfaces.
Wheel and Wheel T rim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned r egularly with a mild soap and water to prevent corr osion. T o remove heavy soil, use Mopar t Wheel Cleaner or select a non- abrasive, non-acidic cleaner .
Y our leather upholstery can be best preserved by r egular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed pr omptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar t T otal Clean.
1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners.
Cavity Cartridge Fuse Mini Fuse Description 1 20 Amp Y ellow Power Outlet Console 2 20 Amp Y ellow Cabin Compartment Node (CCN) Door Locks 3— — 4 15 Amp Blue Aisin T ransmission Controls (Diesel O.
Cavity Cartridge Fuse Mini Fuse Description 12 30 Amp Pink Electric Brake 13 25 Amp Natural Power-Battery R W AL/ABS Module Feed 14 15 Amp Blue Park Lights Left 15 20 Amp Y ellow T railer Park Lights .
Cavity Cartridge Fuse Mini Fuse Description 27 40 Amp Green Power Seats 28 10 Amp Red Power Run/Start- PCM/Steering Angle Sensor 29 10 Amp Red 4X4 Switch/Pass Dr Switch/EC Mirror 30 15 Amp Blue Power .
Cavity Cartridge Fuse Mini Fuse Description 39 10 Amp Red Seatbelt T ension Reducer/Power IGN Run/Acc 40 20 Amp Y ellow Power IGN Run/Acc — Cigar Lighter/Rear Power Point 41 — — 42 30 Amp Pink D.
VEHICLE STORAGE If you are storing your vehicle for mor e than 21 days, we recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: • Disconnect the Ignition-Off Draw fuse (IOD) fuse located in the Integrated Power Module, located in the engine compartment.
REPLACEMENT LIGHT BULBS LIGHT BULBS — Inside Bulb No. Overhead Console Lights ............... T S 212-2 Dome Light ............................ 7679 All of the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not appr oved. LIGHT BULBS — Outside Bulb No.
BULB REPLACEMENT Headlight (Halogen)/Front Park and T urn Lights CAUTION! This is a halogen bulb. A void touching the glass with your fingers. Reduced bulb life will result. 1. Open the hood 2. Remove the two bolts from the front of the headlight housing.
3. Remove the plug from the inner fender well and remove the nut thr ough the access hole. 4. Pull the housing out from the fender to allow room to disconnect the electrical connectors.
NOTE: For easier removal, pull the headlight assembly straight forward, applying the gr eatest amount of force to the outer edge of the headlight assembly .
6. T wist connector on the side marker/turn signal/park light bulb 1 ⁄ 4 turn and remove connector and bulb fr om housing. 7. Remove housing from vehicle with headlight halogen bulb in housing. 8. T wist the headlight halogen bulb 1 ⁄ 4 turn and remove headlight bulb from the housing.
2. Pull bulb straight from the connector . 3. Reverse procedure for installation of bulbs and hous- ing. T ail, Stop, T urn and Backup Lights 1. Remove the two screws that pass thr ough the bed sheetmetal.
2. Pull the housing straight out from the body , with a quick motion, to separate the housing from the body . If not pulled straight, locators may be damaged.
4. Pull bulb straight out of socket. 5. Reverse Procedure to install bulb and housing. Place the two raised blocks past the body . Pulling Bulb From Socket Sliding Raised Blocks Past Body 472 MAINT AI.
Center High-Mounted Stoplight (CHMSL) With Cargo Light 1. Remove the two screws holding the housing/lens to the body as shown. 2. Separate the connector holding the housing and wir- ing harness to the body . 3. T urn desired bulb socket 1 ⁄ 4 turn and remove socket and bulb from housing.
4. Pull desired bulb straight from the socket. • Outside Bulbs: Cargo Lights • Inside Bulb: Center High-Mounted Stop Light 5. Reverse procedure for installation of bulbs and hous- ing. Cab T op Clearance Lights — If Equipped 1. Remove the two screws from the top of the light.
2. Rotate the socket 1 ⁄ 4 turn and pull it from the light assembly . 3. Pull the bulb straight from it’s socket and r eplace. MAINT AINING YOUR VEHICLE 475 7.
T ailgate ID Lights (Dual Rear Wheels) — If Equipped 1. Remove the two screws and housing and access the bulb sockets from the r ear . 2. T urn socket 1 ⁄ 4 turn counterclockwise to access the bulb.
3. Pull bulb straight out from socket. 4. Reverse procedure for installation of bulbs and hous- ing. Rear Light Bar ID Marker (Dual Rear Wheel) — If Equipped 1. Loosen the two screws and the housing to gain access to the bulb sockets. 2. T urn the socket 1 ⁄ 4 turn counterclockwise to access the bulb.
3. Pull the bulb straight out from the socket. 4. Reverse procedure for installation of bulbs and hous- ing. Side Marker Lights (Dual Rear Wheels) 1. Push rearward on the side marker light assembly . 2. Pull the entire assembly from the fender . 3. T urn socket 1 ⁄ 4 turn counterclockwise and r emove from assembly to access the bulb.
FLUID CAP ACITIES FLUID CAP ACITIES U.S. Metric Fuel 2500 Shortbed Models 34 gal 128L 2500 Longbed Models 35 gal 132L 3500 Shortbed Models 34 gal 128L 3500 Longbed Models 35 gal 132L FLUID CAP ACITIES U.S. Metric Engine Oil 6.7L HO T urbo Diesel Engine I-6 (SAE 15W -40, API CJ-4 Certified, that meets CES 20081 Stan- dards.
FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar t Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology). Engine Oil (6.7L T urbo Diesel) Use (SAE 15W -40, API CJ-4 Certified, that meets DaimlerChrysler Material Standards MS-10902.
Component Fluids, Lubricants and Genuine Parts Fuel Selection (6.7L T urbo Diesel Engine) Use good quality diesel fuel from a r eputable supplier in your vehicle.
Chassis Component Fluids, Lubricants and Genuine Parts. Automatic T ransmission Mopar t A TF+4, Automatic T ransmission Fluid. T ransfer Case Mopar t A TF+4, Automatic T ransmission Fluid. Manual T ransmission Fluid G-56 Mopar t A TF+4, Automatic T ransmission Fluid.
MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance ........ 4 8 4 m Maintenance Schedules — 6.7L T urbo Diesel .... 4 8 4 ▫ Oil Change Indicator System ............. 4 8 6 ▫ Perform Service Indicator ............... 4 8 6 ▫ Maintenance Schedule .
EMISSION CONTROL SYSTEM MAINTENANCE The Scheduled maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued pr oper func- tioning of the emission control system.
take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance. Once a Month • Check tire pr essure and look for unusual wear or damage. • Inspect the batteries and clean and tighten the termi- nals as requir ed.
Oil Change Indicator System Y our vehicle is equipped with an engine oil change indicator system. This system will alert you when it is time to change your engine oil by displaying the words “Oil Change Required” on your Electr onic V ehicle Infor- mation Center (EVIC).
Maintenance Schedule (Miles) (7,500) (15,000) (22,500) (30,000) (37,500) Kilometers 12 000 24 000 36 000 48 000 60 000 [Months] [6] [12] [18] [24] [30] Change engine oil and engine oil filter . (Under no cir- cumstances should oil change intervals exceed 12 000 km (7,500 mi) or 6 months, which ever comes first).
(Miles) (45,000) (52,500) (60,000) (67,500) (75,000) Kilometers 72 000 84 000 97 000 109 000 121 000 [Months] [36] [42] [48] [54] [60] Change engine oil and engine oil filter . X X X X X Lubricate Front Drive Shaft Fitting (4X4). X X X X X Rotate tires.
(Miles) (45,000) (52,500) (60,000) (67,500) (75,000) Kilometers 72 000 84 000 97 000 109 000 121 000 [Months] [36] [42] [48] [54] [60] Inspect the brake linings, replace if necessary . X X Inspect and adjust parking brake if necessary . X X Inspect front wheel bearings.
(Miles) (82,500) (90,000) (97,500) (100,000) (105,000) Kilometers 133 000 145 000 157 000 160 000 169 000 [Months] [66] [72] [78] [84] Change engine oil and engine oil filter . X X X X Lubricate Front Drive Shaft Fitting (4X4). X X X X Rotate tires. X X X X Lubricate outer tie rod ends.
(Miles) (1 12,500) (120,000) (127,50) (135,000) (142,500) (150,000) Kilometers 181 000 193 000 205 0000 217 000 229 000 241 000 [Months] [90] [96] [102] [108] [1 14] [120] Change engine oil and engine oil filter . X X XXXX Lubricate Front Drive Shaft Fitting (4X4).
(Miles) (1 12,500) (120,000) (127,50) (135,000) (142,500) (150,000) Kilometers 181 000 193 000 205 0000 217 000 229 000 241 000 [Months] [90] [96] [102] [108] [1 14] [120] Inspect the brake linings, replace if necessary . X X Inspect and adjust parking brake if necessary .
CAUTION! ***The manufacturer highly recommends that all cooling system service, maintenance, and repairs be performed by your local authorized dealer . W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS m Suggestions For Obtaining Service For Y our V ehicle .............................. 4 9 7 ▫ Prepar e For The Appointment ............ 4 9 7 ▫ Prepar e A List ........................ 4 9 7 ▫ Be Reasonable W ith Requests .
m Publication Order Forms .................. 5 0 1 m Department Of T ransportation Uniform T ire Quality Grades ........................ 5 0 3 ▫ T readwear .......................... 5 0 3 ▫ T raction Grades ...................... 5 0 3 ▫ T emperature Grades .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty .
special tools, and the latest information to ensure your vehicle is fixed correctly and in a timely manner . This is why you should always talk to your authorized dealer’s service manager first.
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center .
W ARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
T o contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY : 1–800–424– 9153), or go to http://www .safercar .gov; or write to: Administra- tor , NHTSA, 400 Seventh Street, SW ., W ashington, D.C. 20590.
• Diagnostic Procedure Manuals Diagnostic Procedur e Manuals are filled with dia- grams, charts and detailed illustrations. These practi- cal manuals make it easy for students and technicians to find and fix problems on computer -controlled ve- hicle systems and features.
DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following tire grading categories wer e established by the National Highway T raffic Safety Administration. The specific grade rating assigned by the tire’s manufactur er in each category is shown on the sidewall of the tires on your vehicle.
T emperature Grades The temperature grades ar e A (the highest), B, and C, repr esenting the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10.
Adding Fuel ........................... 3 4 9 Adjustable Pedals ....................... 1 3 8 Air Cleaner , Engine (Engine Air Cleaner Filter) ............................. 419,452 Air Conditioner Maintenance ............... 4 3 0 Air Conditioning Refrigerant .
Shifting ............................. 2 8 5 Special Additives ...................... 4 5 0 Autostick ............................. 1 9 2 Axle Fluid .......................... 446,482 Axle Lubrication (Axle Fluid) ............... 4 4 6 Ball Joints ...
Radiator (Coolant Pressur e) ............... 4 3 9 Car W ashes ............................ 4 5 5 Carbon Monoxide W arning ............... 76,181 Cargo Light ............................ 1 3 3 Cassette T ape and Player Maintenance ......... 2 4 7 Catalyst Full Message .
Drain, Flush, and Refill .................. 4 3 7 Inspection ........................... 4 4 0 Points to Remember .................... 4 4 1 Pressur e Cap ......................... 4 3 9 Radiator Cap ......................... 4 3 9 Selection of Coolant (Antifreeze) .
Electric Rear W indow Defrost ............. 87,173 Electrical Power Outlets ................... 1 6 0 Electronic Range Select (ERS) ............... 2 8 9 Electronic Speed Contr ol (Cruise Control) ...... 1 3 9 Electronic V ehicle Information Center (EVIC) .
F a n .................................. 4 4 2 Filters Closed Crankcase V entilation (CCV) ......... 4 2 6 Engine Oil ..................... 413,416,480 Flashers T urn Signal .......................... 1 3 3 Flat T ire Stowage ..................... 386,396 Fluid, Brake .
V oltmeter ......................... 189,275 Gear Ranges ........................ 285,292 General Information ................. 18,1 15,347 Glass Cleaning .......................... 4 5 8 Grocery Bag Retainer ..................... 1 7 2 Gross Axle W eight Rating .
Illuminated Entry ........................ 2 0 Immobilizer (Sentry Key) ................... 1 5 Infant Restraint ........................ 61,62 Inflation Pressur e T ires .................... 3 3 3 Information Center ...................... 1 4 3 Information Center , V ehicle .
Bulb Replacement ................... 465,466 Cap T op Clearance ..................... 4 7 4 C a r g o .............................. 1 3 3 Center Mounted Stop ................... 4 7 3 Check Engine (Malfunction Indicator) ........ 1 9 4 Cruise .......
Power Door ........................... 2 7 Steering Wheel ......................... 1 8 Lower Anchors and T ether for CHildren (LA TCH) .............................. 6 5 Lubrication, Body ....................... 4 3 3 Lug Nuts .......................
T r i p ............................. 192,199 Off-Pavement Driving (Of f-Road) ............ 3 0 9 Off-Road Driving (Of f-Pavement) ............ 3 0 9 Oil Change Indicator .................. 145,486 Oil, Engine ............................ 4 8 0 Capacity .
Placard, T ire and Loading Information ......... 3 2 0 Power Distribution Center (Fuses) ............... 4 5 9 Door Locks ........................... 2 7 Mirrors .............................. 8 6 Outlet (Auxiliary Electrical Outlet) .......... 1 6 0 Seats .
Remote Keyless Entry (RKE) ................. 2 1 Remote Sound System (Radio) Controls ........ 2 4 6 Replacement Keys ........................ 1 6 Replacement T ires ....................... 3 3 1 Reporting Safety Defects ................... 5 0 0 Resetting Oil Change Indicator .
Reclining ............................ 1 1 7 Reclining Rear ........................ 1 2 1 Security Alarm (Theft Alarm) ............. 19,192 Selection of Coolant (Antifreeze) .......... 438,480 Sentry Key (Immobilizer) ................... 1 5 Sentry Key Programming .
Starting Procedur es ...................... 2 6 8 Starting Procedur es (Diesel Engines) .......... 2 6 8 Steering Linkage ............................. 4 3 2 Power ........................... 315,431 Wheel Lock ........................... 1 8 Wheel, T ilt .
Inflation Pressur es ..................... 3 2 5 Jacking ............................. 3 8 7 Life of T ires .......................... 3 3 0 Load Capacity ..................... 320,321 Pressur e Monitor System (TPMS) ........... 3 3 8 Pressur e W arning Light .
T railer T owing Guide ..................... 3 6 1 T railer W eight .......................... 3 6 1 T ransaxle Automatic ............................ 1 2 Manual .............................. 1 4 T ransfer Case Electronically Shifted ................
W arning Lights (Instrument Cluster Description) ........................... 1 8 9 W arnings and Cautions ..................... 7 W arranty Information ..................... 5 0 0 W ashers, W indshield .................. 136,434 W ashing V ehicle ....
INST ALLA TION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to pr ovide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel.
Ram T ruc k OWNER’ S MANUAL DIESEL 2008 2008 Ram T ruck Diesel 81-326-0828 Second Edition P r inted in U .S.A..
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Dodge 2008 Ram 2500 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Dodge 2008 Ram 2500 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Dodge 2008 Ram 2500 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Dodge 2008 Ram 2500 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Dodge 2008 Ram 2500, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Dodge 2008 Ram 2500.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Dodge 2008 Ram 2500. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Dodge 2008 Ram 2500 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
