Manuale d’uso / di manutenzione del prodotto ZTR 5601 del fabbricante Dixon
Vai alla pagina of 72
.
IMPORTANT - READ CAREFULLY The Dixon ® ZTR ® Mower is both easy and fun to operate. However, any power mower must be operated properly to be safe. It is not a toy or a recreational vehicle. Before you start to use the mower, read the operator's manua l carefully and become completely familiar with the controls.
Part No. 8965 September 1995 INDEX SAFETY ............................................................ Pages 1 - 6 WARRANTY POL ICY ......................................... Page 7 SPECIFICATIONS .............................................. Page 8 - 10 SEAT ADJUSTMENT .
SAFETY RIDING LAWNMOWERS, IF IMPROPERLY OPERATED, CAN CAUSE SERIOUS INJURY OR DEATH The most common causes of injury to the operator or bystander... TIP - OVER Page 1.
SAFETY SAFETY SYMBOLS: SAFETY ALERT SYMBOL - When you see this symb ol, BE ALERT to the potential for injury. Follow recommended safety precautions and safe operating practices. Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
This cutting mower is capable of amputating hands and feet, and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. GENERAL OPERATION: * Read, understand, and follow al l instructions in the manual and on the mower before starting.
SAFETY SLOPE OPERATION: Slopes are a major factor related to loss - of - control and tip - over accidents, 'which can result in severe injury or death. All slopes require extra caution. - . If you cannot back up the slope or if you feel uneasy on it, do not mow it.
SAFETY CHILDREN: Tragic accidents can occur if the operator is not alert to the presence of children. Children are attracted to lawn mowers and the mowing acti vity. NEVER assume children will stay where they were last seen. Be alert to avoid accidents.
SAFETY SERVICE: • Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. Use only an approved container. Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling. Do not smoke.
DIXON LIMITED WARRANTY POLICY -- HYDRO - GEAR MODEL S This warranty policy applies to all HydroGear mowers or any 50" model, purchased on or after March 1,1990. WARRANTY: Dixon Warranty term is for a period of one (1) year from date of purchase or 400 hours of use, whichever occurs first.
SPECIFICATIONS Model ZTR 5422 CHASSIS: 11 GA - rectangular tube BODY: Two piece - made of rotational molded polyethylene. Front body contains access panels for battery s ervice and engine to mower deck belt removal. Rear body tilts up to allow service on the entire drive system.
SPECIFICATIONS Model ZTR 5502 CHASSIS: 1 1 GA - rectangular tube BODY: Two piece - made of rotationa l molded polyethylene. Front body contains access panels for battery service and engine to mower deck belt removal. Rear body tilts up to allow service on the entire drive system.
SPECIFICATIONS Model ZTR 5601 CHASSIS: 11 GA - rectangular tube BODY: Tw o piece - made of rotational molded polyethylene. Front body contains access panels for battery service and engine to mower deck belt removal. Rear body tilts up to allow service on the entire drive system.
SEAT ADJUSTMENT INSTRUCTIONS Models ZTR 5422 - ZTR 5502 - ZTR 5601 : 1. Place parking brake in ON position. (Pull brake lev er up) 2. Raise and push seat assembly and upper body rearward. 3. Loosen two front seat adjustment knobs, P/N 3978, and slide seat forward or backward to desired position.
CONTROLS Page 12.
CONTROLS PARKING BRAKE: The parking brake used on the 5000 Series Models is designed to hold the mower from moving and is not intended for use in stopping the mower while it is in motion. Engage parking brake before starting engine. Do not leave engine running for extended periods of time without the parking brake engaged.
TO GO FORWARD: From neutral position, gent ly push both drive levers forward. To increase speed, move levers farther forward. TO GO BACKWARD: From neutral position, gently pull both drive levers toward you. TURNING: Turning is controlled by moving one drive lever slightly forward or rearward of the other.
CONTROLS BLADE DRIVE: Located on control panel, on operator's right. To engage the mower blades, lift switch up lightly and push forward. To disengage blades, pull switch backward. Switch is clearly marked "on and off ". CIRCUIT BREAKER: Located on control panel, on operator's right.
OPERATION INSTRUCTIONS The safe and successful operation of the 5000 Series Models will depend upon the operator having the correct knowledge of all controls used on the mower and making good judgements about the terrain to be mowed. NEVER allow anyone to operate the mower without complete knowledge of all controls and their functions.
OPERATION INSTRUCTIONS PARKING BRAKE SWITCH TEST: With parking brake in the OFF position, engine should not turn over or attempt to start when the key switch is moved to the start position.
OPERATION INSTRUCTIONS STARTING INSTRUCTIONS: Cold Engine 1 . Push choke control lever fully forward. 2. Push throttle control lever to 1/2 setting. 3. Insert ignition key and turn to "Start" position. When engine s tarts, release ignition key.
OPERATION INSTRUCTIONS STARTING INSTRUCTIONS: Engine has been operated. 1. Move throttle control lever to 1/4 to 1/2 setting. 2. Insert ignition key and turn to "Start" position. When engine starts, release ignition key. Key will retu rn to "Run" position.
OPERATION INSTRUCTIONS M OWING WITH A MULCHING ATTACHMENT: Mulching or recycling the grass clippings requires a totally different mowing approach than would be normal when side discharging or bagging the grass. There may be instances or conditions where it is not possible to hide all of the recycled or mulched clippings.
OPERATI ON INSTRUCTIONS MOWING WITH A GRASS CATCHER ATTACHMENT: In order to achieve optimum performance when mowing with a grass catching attachment, please read and follow the tips listed below. 1 . Set engine speed control to the wide open or full settin g.
OPERATION INSTRUCTIONS SIDE DISCHARGE OF THE CLIPPING S: In order to achieve optimum performance when side discharging the grass clippings, please read and follow the tips listed below. Additional information can be found in the troubleshooting guide on page 41.
OPERATION INSTRUCTIONS DECK ROLLERS: Purpose: The spring loaded deck rollers located at the front corners of the mower deck are designed as an aid to limit turf scalping when mowing on uneven ground. Height: Normal height settings as installed at the factory allows each roller to ride slightly above the turf.
CARE AND MAINTENANCE - 5000 SERIES MODELS This portion of the 5000 Series Models owners manual deals with normal service items which can be performed by the owner.
CARE AND MAINTENANCE - 5000 SERIES MODELS CUTTER BLADE MAINTENANCE: NOTE: Observe proper blade position prior to removal. 1 . Safely raise front of mower. 2. Hold or block blade from turning. CAUTION Wear heavy, thick gl oves when holding onto cutter blade, avoid the sharp edge of the blade.
CARE AND MAINTENANCE - 5000 SERIES MODELS BELT TENSION ENGINE TO MOWER DEC K BELT: Models ZTR 5422 & ZTR 5502 P/N 61 1 1 Model ZTR 5601 P/N 6939 MOWER DECK SERPENTINE BELT: Model ZTR 5422 P/N 6109 Model ZTR 5502 P/N 1300 Model ZTR 5601 P/N 6938 Refer to illustration for adjustment procedure.
CARE AND MAINTENANCE - 5000 SERIES MODELS FUEL SHUT OFF VALVE: A fuel shut off valve is located at the bo ttom rear of each fuel tank. Always turn the valve to the "OFF" position when the mower is stored or not in use.
CARE AND MAINTENANCE - 5000 SERIES MODELS 5000 SERIES REAR WHEELS: The rear wheels of all 5000 Series models are of an "offset" center design to allow "reversed" installation for using snow chains or to gain increased stability when mowing on sloped ground.
CARE AND MAINTENANCE - 5000 SERIES MODELS CAUTION HOT oil may cause burns. Allow engine to cool before draining oil. CHANGING THE ENG INE OIL: 1 . The "snap lock" oil drain valve is located on the left side of the engine crankcase. 2. Place a suitable container under the drain valve.
CARE AND MAINTENANCE - 5000 SERIES MODELS MOWER DECK INSTALLATION: NOTE: B rake link (P/N 5283) normally used for installation of engine to mower deck drive belt, has been placed in position during assembly of the lift frame at the factory. For shipment purposes, the brake link has been secured with a cotter pin and washer.
CARE AND MAINTENANCE - 5000 SERIES MODELS MOWER DECK LEVELING PROCEDURE: There are a total of (4) threaded adjusters which will control the attitude or pitch of the mower d eck. The adjusters have lock nuts on the bottom which can be turned up or down to raise or lower the front and rear of the mower deck.
CARE AND MAINTENANCE - 5000 SERIES MODELS Adjustment of the drive system is limited to the a ctual function of the hydrostatic transmissions as outlined below.
CARE AND MAINTENANCE - 5000 SERIES MODELS PARKING BRAKE CABLE ADJUSTMENT: Position parking brake lever in the off or disengaged position. This will allow the belt idler used on the engine to T - box to swing full y and apply tension to the belt.
CARE AND MAINTENANCE - 5000 SERIES MODELS NEUTRALADJUSTMENT : Swing upper control levers out into the neutral slots. Raise upper body to the fully open position. Start engine and disengage parking brake. Caution should be used when releasing parking brake as mower may tend to creep or move prior to adjustment.
CARE AND MAINTENANCE - 5000 SERIES MODELS FORWARD TRAVEL SPEED ADJUSTMENTS: Stop engine, move levers to drive position, lightly push each upper control lever forward until a resistance is felt on the lever. At this time, check that the forward leve r stops on the bottom of each lever are hitting the stop blocks.
CARE AND MAINTENANCE - 5000 SERIES MODELS PROCEDURE FOR ELECTRIC CLUTCH ADJUSTMENT Electric clutches require periodic Air Gap adjust ments to extend the life of the clutch. Listed below is both an Air Gap adjustment procedure and an Ohms test to check for a faulty coil within the clutch.
CARE AND MAINTENANCE - 5000 SERIES MODELS HYDROST ATIC TRANSMISSION OIL AND FILTER SERVICE SERVICE INTERVALS: 1. Initial oil and filter service - 50 hours. 2. Every 250 hours thereafter. OIL REQUIREMENTS: Any high quality engine oil with an API classification of SG/CD is recommended.
CARE AND MAINTENANCE - 5000 SERIES MODELS WHEELS AND TIRES: Correct tire pressure is important for correct operation of mower. Model ZTR 5422 Front Tires 11X4X4 Air Pressure 16 - 21 Ibs. Rear Tires 18 X 9.50 X 8 Air Pressure 8 - 14 Ibs. Models ZTR 5502 & ZTR 5601 Front Tires 11X4X5 Air Pressure 16 - 21 Ibs.
STANDARD SERVICE PARTS LIST MODEL ZTR 5422: BLADES: Standard: P/N 6236 Hi - Lift: P/N 8688 BELTS: Engine To Mo wer Deck: P/N 61 1 1 Serpentine Belt: P/N 6109 Engine To T - Box: P/N 1714 T - Box To Hyd.
STANDARD SERVICE PARTS LIST KOHLER AIR AND OIL FILTER PART NUMBERS: Refer to engine manufacturers manual for recommendations regarding frequency of servic e required for engine oil changes and air filter maintenance. Protect your engine investment, use only original equipment filters.
TROUBLESHOOTING MOWER CUT QUALITY: There are many variables that can effect the cut quality of any riding mower. Type and conditions of grass, cut height setting, engine RPM and ground spe ed are some of the variables that interact creating differences in cut quality.
TROUBLESHOOTING DRIVE SYSTEM: t' - SITUATION CAUSES REMEDY Mower pulls to one side or the other Drive adjustment Consult your dealer for repair Drive system will not function on either side after.
TROUBLESHOOTING ELECTRICAL SYSTEM: SITUATION CAUSES REMEDY Starter will not turn engine over Circuit breaker engaged Push button to reset Consult your dealer for repair Starter will not turn engine ov.
Page 44.
Page 45.
Page 46.
Page 47.
Page 48.
Page 49.
Page 50.
Page 51.
Page 52.
Page 53.
Page 54.
Page 55.
Page 56.
Page 57.
Page 58.
Page 59.
Page 60.
Page 61.
Page 62.
DIXON INDUSTRIES, INC A BLOUNT COMPANY AIRPORT INDUSTRIAL PARK PO BOX 1569 COFFEYVILLE KS 67337 O945 316 251 2OOO FAX 316 251 4117 OWNER INFORM ATION DATE PURCHASED MOWER MODEL NUMBER PURCHASED FROM N.
NOTES.
.
NOTES.
.
NOTES.
WARNI NG: The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Dixon ZTR 5601 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Dixon ZTR 5601 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Dixon ZTR 5601 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Dixon ZTR 5601 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Dixon ZTR 5601, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Dixon ZTR 5601.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Dixon ZTR 5601. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Dixon ZTR 5601 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
