Manuale d’uso / di manutenzione del prodotto ZTR 5000 Series del fabbricante Dixon
Vai alla pagina of 48
.
IMPORTANT - READ CAREFULLY The Dixon ® ZTR ® Mower is both easy and fun to operate. However, any power mower must be operated properly to be safe. It is not a toy or a recreational vehicle. Before you start to use the mower, read the operator's manual carefully and become completely familiar with the controls.
INDEX SAFETY ............................. ................. ........ Pages 2 - WARRANTY POLICY ............................. ........ Page 8 SPECIFICATIONS ................................. ........ Page 9 SEAT ADJUSTMENT ............................
SAFETY RIDING LAWNMOWERS, IF IMPROPERLY OPERATED, CAN CAUSE SERIOUS INJURY OR DEATH The most common causes of injury to the operator or bystander... ..
SAFETY ALERT SYMBOL - When you see this symbol, BE ALERT to the potential for injury. Follow recommended safety precautions and safe operating practices. Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
SAFETY This cutting mower is capable of amputating hands and feet, and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. GENERAL OPERATION: • Read, understand, and follow all instructions in the manual and on the mower before starting.
SAFETY SLOPE OPERATION: Slopes are a major factor related to loss - of - control and tip - over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.
SAFETY CHILDREN: Tragic accidents can occur if the operator is not alert to the presence of children. Children are attracted to lawn mowers and the mowing activity. NEVER assume children will stay where they were last seen. Be alert to avoid accidents.
SAFETY SERVICE: • Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. Use only an approved container. Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling. Do not smoke.
DIXON LIMITED WARRANTY POLICY -- HYDRO - GEAR MODELS This warranty policy applies to all HydroGear mowers or any 50" model, purchased on or after March 1,1990. WARRANTY: Dixon Warranty term is for a period of one (1) year from date of purchase or 400 hours of use, whichever occurs first.
SPECIFICATIONS Model ZTR 5022 CHASSIS: 1 1 GA - rectangular tube BODY: Two piece - made of high - density polyethylene. Front body contains access panels for battery service and engine to mower deck belt removal. Rear body tilts up to allow service on the entire drive system.
SEAT ADJUSTMENT INSTRUCTIONS Model ZTR 5022: 1. Set parking brake. 2. Raise upper body. 3. Loosen two front seat adjustment knobs and slide seat forward or backward tc desired position. 4. Re - tighten front seat adjustment knobs. DO NOT operate mower without seat adjustments properly tightened.
5000 Series CONTROLS Page 11.
CONTROLS PARKING BRAKE: The parking brake used on the 5000 Series Models is designed to hold the mower from moving and is not intended for use in stopping the mower while it is in motion. Engage parking brake before starting engine Do not leave engine running for extended periods of time without the parking brake engaged.
CONTROLS TO GO FORWARD: From neutral position, gently push both drive levers forward. To increase speed, move levers fa rther forward. TO GO BACKWARD: From neutral position, gently pull both drive levers toward you. TURNING: Turning is controlled by moving one drive lever slightly forward or rearward of the other.
BLADE DRIVE: CONTROLS Located on control panel, on operator's right. 1998 Models To engage blades: Slide switch to rear and flip up and forward. To disengage blades: Flip switch down. 1999 Models To engage blades: Pull switch up. To disengage blades: Push switch down.
OPERATION INSTRUCTIONS The safe and successful operation of the 5000 Series Models will depend upon the operator having the correct knowledge of all controls used on the mower and making good judgements about the terrain to be mowed. NEVER allow anyone to operate the mower without complete knowledge of all controls and their functions.
OPERATION INSTRUCTIONS PARKING BRAKE SWITCH TEST: With parking brake in the OFF position, engine should not turn over or attempt to start when the key switch is moved to the start position.
OPERATION INSTRUCTIONS STARTING INSTRUCTIONS: Cold Engine 1. Position choke control in ON position. 2. Position throttle control at 1/2 speed setting. 3. Insert ignition key and turn to "Start" position. When engine starts, release ignition key.
OPERATION INSTRUCTIONS STARTING INSTRUCTIONS: Engine has been operated. 1. Move throttle control to 1/4 to 1/2 setting. 2. Insert ignition key and turn to "Start" position. When engine starts, release ignition key. Key will return to "Run" position.
OPERATION INSTRUCTIONS MOWING WITH A MULCHING ATTACHMENT: Mulching or recycling the grass clippings requires a totally different mowing approach than would be normal when side discharging or bagging the grass. There may be instan ces or conditions where it is not possible to hide all of the recycled or mulched clippings.
OPERATION INSTRUCTIONS MOWING WITH A GRASS CATCHER ATTACHMENT: In order to achieve optimum performance when mowing with a grass catching attachment, please read and follow the tips listed below: 1. Set engine speed control to the wide open or full setting.
OPERATION INSTRUCTIONS SIDE DISCHARGE OF THE CLIPPINGS: In order to achieve optimum performance when side discharging the grass clippings, please read and follow the tips listed below. Additional information can be found in the troubleshooting guide on page 40.
OPERATION INSTRUCTIONS DECK ROLLERS: 60" Deck Purpose: The spring loaded deck rollers located at the front corners of the 60" mower deck are designed as an aid to limit turf scalping when mowing on uneven ground. Height: Normal height settings as installed at the factory allows each roller to ride slightly above the turf.
CARE AND MAINTENANCE This portion of the 5000 Series Models owners manual deals with normal service items which can be performed by the owner. Please remember that if you are in doubt as to the correc.
CARE AND MAINTENANCE MOWER BLADE MAINTENANCE: NOTE: Observe proper blade position prior to removal. 1. Safely raise front of mower. 2. Hold or block blade from turning. 3. Loosen blade nut and re m ove blade. Wear heavy, th ick gloves when holding onto mower blade, avoid the sharp edqe of the b | ade.
CARE AND MAINTENANCE ENGINE TO MOWER DECK BELT: 42' and 50" P/N 6111 60" P/N 6938 The engine to mower deck drive belts are automatically held in proper tension by springs which push the deck assembly forward and do not require any additional adjustment to be made.
CARE AND MAINTENANCE FUEL SHUT OFF VALVE: A fuel shut off valve is located at the bottom rear of each fuel tank. Always turn the valve to the "OFF" position when the mower is stored or not in use.
CARE AND MAINTENANCE 5000 SERIES REAR WHEELS: The rear wheels of all 5000 Series models are of an "offset" center design to allow "reversed" installation for using snow chains or to gain increased stability when mowing on sloped ground.
CARE AND MAINTENANCE HOT oil may cause burns. Allow engine to cool before draining oil. CHANGING THE ENGINE OIL: 1. The "snap lock" oil drain valve is located on the left side of the engine crankcase. 2. Place a suitable container under the drain valve.
CARE AND MAINTENANCE MOWER DECK REMOVAL: 1. Remove mower deck drive belt. To relieve belt tension, insert 5283 link (at front of lift frame) into tab illustrated below. Move lift handle into the lowest c ut positon. Belt can now be removed from mower deck pulley.
CARE AND MAINTENANCE MOWER DECK LEVELING PROCEDURE: There are a total of (4) threaded adjusters which will control the attitude or pitch of the mower deck. The adjusters have lock nuts on the bottom which can be turned up or down to raise or lower the front and rear of the mower deck.
CARE AND MAINTENANCE Adjustment of the drive system is limited to the actual function of the hydrostatic transmissions as outlined below. T - BOX TO HYDROSTAT BELT ADJUSTMENT: Tighten the (2) J - bolt.
CARE AND MAINTENANCE PARKING BRAKE CABLE ADJUSTMENT: Make necessary adjustments to the T - Box to Hydrostat belt, as shown on page 30. Position parking brake lever in the off or disengaged position. This will allow the belt idler use d on the engine to T - box to swing fully and apply tension to the belt.
CARE AND MAINTENANCE NEUTRAL ADJUSTMENT: 1. Engage parking brake, and raise rear of frame with jack or blocks so that rear tires do not contact the ground. 2. Swing out the control levers, start the engine, and release the parking brake. 3. Raise the upper body to access hydro control linkage.
CARE AND MAINTENANCE 6. Drive machine with both levers in top speed position. If one side now drives slightly faster than the other adjust forward speed bolt in to contact stop sooner. If levers are now uneven at top speed, loosen control lever mounting nut.
CARE AND MAINTENANCE PROCEDURE FOR ELECTRIC CLUTCH ADJUSTMENT Electric clutches require periodic Air Gap adjustments for extended life. Listed below is both an Air Gap adjustment procedure and an Ohms test to check for a faulty coil within the clutch.
CARE AND MAINTENANCE HYDROSTATIC TRANSMISSION OIL AND FILTER SERVICE SERVICE INTERVALS: 1 . Initial oil and filter service - 50 hours. 2. Every 250 hours thereafter. OIL REQUIREMENTS: Any high quality engine oil with an API classification of SG/CD is recommended.
CARE AND MAINTENANCE HYDROSTATIC TRANSMISSION OIL AND FILTER SERVICE If transmission is to be serviced, proper air purging procedures must be followed, or damage will occur. Proceed as follows: 1. Remove oil filter from ch assis, allowing oil to drain into container.
CARE AND MAINTENANCE WHEELS AND TIRES: Correct tire pressure is important for correct operation of mower. Air Pressure 16 - 21 Ibs. (Front) Air Pressure 8 - 14 Ibs. (Rear) NOTE: Check lug nuts periodically for tightness. ELECTRICAL SYSTEMS: Keep all connections clean and tight.
STANDARD SERVICE PARTS LIST 42" DECK BLADES: LoLift: P/N 6236 Standard Hi - Lift: P/N8688 BELTS: Engine To Mower Deck: P/N6111 Serpentine Belt: P/N6109 Engine To T - Box: P/N 171 4(1 998 models) .
STANDARD SERVICE PARTS LIST KOHLER AIR AND OIL FILTER PART NUMBERS: Refer to engine manufacturers manual for recommendations regarding frequency of service required for engine oil changes and air filter maintenance. Protect your engine investment, use only original equipment filters.
TROUBLESHOOTING MOWER CUT QUALITY: There are many variables that can affect the cut quality of any riding mower. Type and conditions of grass, cut height setting, engine RPM and ground speed are some of the variables that interact creating differences in cut quality.
TROUBLESHOOTING DRIVE SYSTEM: SITUATION CAUSES REMEDY Mower pulls to one side or the other Forward travel speed adjustment Refer to page 33 for procedure or consult your dealer for repair Drive system.
TROUBLESHOOTING ELECTRICAL SYSTEM: SITUATION CAUSES REMEDY Starter will not turn engine over Circuit breaker disengaged Push button to reset Consult your dealer for repair Starter will not turn engine.
NOTES.
DIXON INDUSTRIES, INC. A BLOUNT International Inc.Co. PO BOX 1569 COFFEYVILLE KS 67337 0945 316251 2000 OWNER INFORMATION.
WARNING: The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive ha rm. ® Dixon and ZTR are registered trademarks of Dixon Industries, Inc. DIXON INDUSTRIES, INC. A BLOUNT International Inc.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Dixon ZTR 5000 Series è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Dixon ZTR 5000 Series - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Dixon ZTR 5000 Series imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Dixon ZTR 5000 Series ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Dixon ZTR 5000 Series, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Dixon ZTR 5000 Series.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Dixon ZTR 5000 Series. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Dixon ZTR 5000 Series insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
