Manuale d’uso / di manutenzione del prodotto ZTR 2560 del fabbricante Dixon
Vai alla pagina of 44
Model Year 2004 Model Year 2004 Model Year 2004 Model Year 2004 Model Year 2004 ZTR® Model 2560 Model 2560 Model 2560 Model 2560 Model 2560.
IMPORTANT - READ CAREFULLY The Dixon ® ZTR ® Mower is both easy and fun to operate. However, any power mower must be operated properly to be safe. It is not a toy or a recreational vehicle. Before you start to use the mower, read the operator’s manual carefully and become completely familiar with the controls.
3 INDEX Page Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Warranty Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Seat Adjustment Instructions.
4 RIDING LAWN MOWERS, IF IMPROPERLY OPERATED, CAN CAUSE SERIOUS INJURY OR DEATH. The most common causes of injury to the operator or bystander... ...read and understand this manual to prevent injuries.
5 Safety Alert Symbol When you see this symbol, BE ALERT to the potential for injury. DANGER (highlighted in red) indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
6 Failure to observe the following safety instructions could result in serious injury or death. GENERAL OPERATION: •Read, understand, and follow all instructions in the manual and on the mower before starting. •Only allow responsible adults, who are familiar with the instructions, to operate the mower.
7 GENERAL OPERATION (continued) : •Turn off blades when not mowing. •Stop engine before removing grass catcher or unclog- ging chute. •Mow only in daylight or good artificial light. •Do not operate the mower while under the influence of alcohol or drugs.
8 SLOPE OPERATION: Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it ! DO •Mow across the slope with your Dixon ZTR - never up or down.
9 DO (CONTINUED) •Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly down the slope. •If front wheels lift off the ground, pull the levers back to stabilize the mower. DO NOT • Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible.
10 SAFETY CHILDREN: Tragic accidents can occur if the operator is not alert to the presence of children. Children are attracted to lawn mowers and the mowing activity. NEVER assume children will stay where they were last seen. Be alert to avoid accidents.
11 SERVICE: •Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. Use only an approved container. Never remove fuel cap or add fuel with engine running. Allow engine to cool before refueling. Do not smoke while refueling.
12 SERVICE (continued): •Never run a mower inside a closed area. The exhaust fumes are toxic. •Keep nuts and bolts tight, especially blade attachment bolts, and keep equipment in good condition. •Never tamper with safety devices. Check their proper operation regularly.
13 DIXON LIMITED W ARRANTY POLICY Pro Models 1950 ~ 2300 ~ 2560 DIXON ZTR MOWERS ARE W ARRANTED AGAINST DEFECTS IN MA TERIALS AND WORKMANSHIP AND PROVIDES FOR REPLACEMENT OR REP AIR OF P ARTS INCLUDING LABOR COSTS. THIS WARRANTY IS SUBJECT T O THE FOLLOWING CONDITIONS AND LIMIT A TIONS.
14 SPECIFICATIONS Model 2560 CHASSIS: Folded sheet metal and rectangular tube BODY: Folded sheet metal SEAT: Designed for operator comfort with suspension system and padded back and arm rests. Seat is adjustable fore and aft. MOWER DECK: Deck is made of 10 GA fabricated welded construction with 7 GA reinforcement plates.
15 SEAT ADJUSTMENT INSTRUCTIONS Model 2560 1. Grasp seat slide adjuster and move it into adjustment position. 2 . Slide seat forward or backward. 3 . Release seat slide adjuster.
16 CONTROLS.
17 CONTROLS CONTROL LEVERS Note: For access to the seat, move control levers to neutral position and swing them outward. TO GO FORWARD: • From neutral position, gently push both control levers forward. • To increase speed, move levers further forward.
18 CONTROLS CHOKE CONTROL LEVER: • Located on control panel to operator’s right. • Used to start a cold engine. THROTTLE CONTROL LEVER: • Located on contol panel to operator’s right.
19 CONTROLS BLADE DRIVE: Located on control panel, on operator's right. To engage blades: Pull up on the switch. To disengage blades: Push down. MOWER DECK CUT HEIGHT LIFT LEVER: Located to the right and front of the operator. Controls the cutting height.
20 OPERATION INSTRUCTIONS The safe and successful operation of the ZTR Model 2560 will depend upon the operator having the correct knowledge of all controls used on the mower and making good judgements about the terrain to be mowed. NEVER allow anyone to operate the mower with- out complete knowledge of all controls and their functions.
21 BEFORE OPERATING MOWER: 1 . Read and observe all safety instructions on your mower and in the manual. 2 . Read engine manufacturer’s operating and maintenance instructions. 3 . Discuss proper maintenance with your dealer. 4 . Check engine oil. 5 .
22 OPERATION INSTRUCTIONS TESTING OF SAFETY INTERLOCK SYSTEMS: Do not operate mower if safety switches are not operating properly. Your Zero Turning Radius Mower is equipped with control interlocks for your safety. 1. The mower blades must be disengaged before the engine will start.
23 OPERATION INSTRUCTIONS BLADE DRIVE SWITCH TEST (ELECTRIC CLUTCH): 1. With the electric blade drive switch turned on and the parking brake in “ON” position, engine should not turn over or attempt to start when key switch is moved to the start position.
24 OPERATION INSTRUCTIONS STARTING INSTRUCTIONS (cold engine): 1 . Pull choke control lever up. 2 . Push throttle control lever to 1/2 setting. 3 . Insert ignition key and turn to “START” position. When engine starts, release ignition key. Key will return to “RUN” position.
25 OPERATION INSTRUCTIONS STARTING INSTRUCTIONS (engine has been operated): 1 . Move throttle control lever to 1/4 to 1/2 setting. 2 . Insert ignition key and turn to “START” position. When engine starts, release ignition key. Key will return to “RUN” position.
26 OPERATION INSTRUCTIONS In order to achieve optimum cutting performance, please read and follow the tips listed below. Additional information can be found in the Troubleshooting Guide on Page 40-41. CAUTION Be sure that deflector is properly installed on the discharge chute.
27 GRASS HEIGHT AND CUTTING SUGGESTIONS: Do not attempt to cut grass when it is wet. If the grass is tall, place the mower deck cut height lever in the top or second notch. “Initially” overlap cutting swaths instead of a full swath with each pass.
28 OPERATION INSTRUCTIONS TO FREE WHEEL MACHINE (UNLOCK TRANSMISSION): Always turn off engine before engaging or disengag- ing the hydro release (free wheel) valves. Never attempt to move the valves with the engine running. The hydro release valves are located beneath the seat, between the fuel tank and hydro pumps.
29 CARE AND MAINTENANCE CAUTION CAUTION CAUTION CAUTION CAUTION Before performing any maintenance, turn off engine, allow to cool, remove key & disconnect spark plugs. Use extreme care when working on machinery . Do not wear watch or jewelry . Do not wear loose fitting clothes, and observe all common safety practices with tools.
30 CARE AND MAINTENANCE ENGINE: For complete maintenance and operating information of the engine, please refer to the maintenance instructions furnished by the engine manufacturer and included in your Zero Turn Radius mower information packet. Note: Air intake screen must be kept clean.
31 CARE AND MAINTENANCE CAUTION Stop engine and remove ignition key for safety. Wear heavy, thick gloves when holding onto cutter blade, avoid the sharp edge of the blade. DANGEROUS! DO NOT USE BLADE IN THIS CONDITION! When notch starts, discard blade New Blade MOWER BLADES: Check sharpness of mower blades after every 10 hours of operation.
32 CARE AND MAINTENANCE LUBRICATION: 1 . Engine: Follow engine manufacturer’s recommenda- tion. 2 . Deck spindles: Lubricate with 3 “shots” only, every 100 hours. HYDROSTATIC TRANSMISSIONS: Before each use, check to be sure that the cooling fins and fans of the pumps and wheelmotors are clean.
33 CARE AND MAINTENANCE ELECTRICAL SYSTEMS: Keep all connections clean and tight. CLEANING THE MOWER: Wash mower periodically. Clean above and below the deck. High pressure washing and alkaline based soaps can cause damage to bearings and other parts of the mower.
34 CARE AND MAINTENANCE HYDROSTAT OIL MAINTENANCE PROCEDURE: Check the oil level in hydrostatic transmisison oil reser- voir after every 25 hours of usage. Clean the oil reser- voir cap and the area around it prior to removal. Check the oil level. Oil should be approximately 1-3/8” below top of oil tank.
35 A . Move cut height adjustment lever to lowest position. B . Flip up the foot deck to allow access to the en- gine to deck drive belt. Roll the engine to deck drive belt off the center spindle. C . Lift the rear corner of the deck and remove 1/2” x 1-1/2” clevis pin from lift link/eye bolt.
36 CARE AND MAINTENANCE MOWER SHOWN IN OPERATION POSITION.
37 MOWER SHOWN IN SERVICING POSITION CARE AND MAINTENANCE.
38 CARE AND MAINTENANCE LEVELING THE DECK: 1. Set the tire pressure on all 4 tires. 2. Front casters must be rotated in the direction of forward travel. 3. Move the tractor to a hard level surface. 4. Put the mower deck in the number 3 deck height position.
39 STANDARD SERVICE PARTS LIST MODEL ZTR 2560: Blades 60” Hi-Lift (Standard)-P/N 12421 Low-lift-P/N 12451 Gator-P/N 12508 Belts Engine to Mower Deck Belt-P/N 1300 Serpentine Belt 60”-P/N 9758 Engi.
40 1. ENGINE WON’T TURN OVER Mower blades engaged- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - disengage blades Blown fuse- - - - - - - - - - - - - - - - - - - - - - - - - - - .
41 TROUBLESHOOTING 6. ENGINE OVERHEATED Air intake screen or fins clogged- - - - - - - - - - - - - - - - - - -clean intake screen and fins Oil level too low or too high- - - - - - - - - - - - - - - - .
42 NOTES.
43 OWNER INFORMATION Date Purchased _ ________________________________ Mower Model Number__________________________ Mower Serial Number ____________________________ Purchased From ___ ________________.
ZTR®Mowers ZTR®Mowers ZTR®Mowers ZTR®Mowers ZTR®Mowers Dixon® and ZTR® are registered trademarks of Dixon Industries, Inc. DIXON INDUSTRIES, INC. a BLOUNT International Inc. Co. P.O. Box 1569 Coffeyville, Ks 67337-0945 620-251-2000 Model 2560 Part No.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Dixon ZTR 2560 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Dixon ZTR 2560 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Dixon ZTR 2560 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Dixon ZTR 2560 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Dixon ZTR 2560, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Dixon ZTR 2560.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Dixon ZTR 2560. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Dixon ZTR 2560 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
