Manuale d’uso / di manutenzione del prodotto KOH/968999590 del fabbricante Dixon
Vai alla pagina of 52
BLACK BEAR ™ ZTR ® Operator’s Manual GRIZZLY SERIES ™ ZTR ® GRIZZLY 52, 27 KOH/968999588 GRIZZLY 60, 27 KOH/968999590 GRIZZLY 60, 30 KOH/968999591 GRIZZLY 72, 27 KOH/968999592 Please read the operator’s manual carefully and make sure you understand the instructions before using the unit.
2.
3 IMPORTANT - READ CAREFULLY The Dixon® ZTR® mower is both easy and fun to operate. However, any power mower must be operated properly to be safe. It is not a toy or a recreational vehicle. Before you start to use the mower, read this Operator’s Manual carefully.
4.
5 TABLE OF CONTENTS GRIZZLY SERIES™ Part Number 539 114590R1 GENERAL OPERATION .................................................................. 8-9 SLOPE OPERATION ................................................................... 10-11 ROLL OVER PROTECTION SYSTEM (ROPS) .
SAFETY 6 Blade Contact Tip Over Run Over Back Over RIDING LAWN MOWERS, IF IMPROPERLY OPERATED, CAN CAUSE SERIOUS INJURY OR DEATH Pictured below are the most common causes of injury to the operator or bystander. Please read and understand this manual to prevent injuries.
SAFETY 7 Safety Alert Symbol DANGER (highlighted in red) indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING (highlighted in orange) indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
WARNING 8 GENERAL OPERATION Read, understand, and follow all instructions in this manual and on the mower before starting. Only allow responsible adults, who are familiar with the instructions, to operate the mower. Clear the area of objects such as rocks, toys, wire, etc.
WARNING 9 WARNING ! Failure to observe the following instructions could result in serious injury or death. To avoid personal injury from accidental clutch engagement, stop engine before removing grass catcher or unclogging chute. Mow only in daylight or good artificial light.
WARNING 10 WARNING ! Failure to observe the following instructions could result in serious injury or death. SLOPE OPERATION Slopes are a major factor related to loss-of-control and tip- over accidents, which can result in severe injury or death. All slopes require extra caution.
WARNING 11 SLOPE OPERATION (continued) DO NOT Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible. Rapid uphill turns may cause tip- over. Do not mow near drop-offs, ditches, or embankments. Unstable ground may cause loss of control.
WARNING 12 ROLL OVER PROTECTION SYSTEM (ROPS) The ROPS increases the basic weight of the unit by 42 Ibs/19 kg. The ROPS on the US units are standard, on the European unit the ROP is an accessory. The ROP’s capability may be impaired by structural damage if overtumed or alterations are made.
WARNING 13 ROLL OVER PROTECTION SYSTEM (ROPS) (continued) • Operate the mower smoothly - no jerky turns, starts or stops. • When mower is stopped, set brakes securely and use park brake. • If any part of ROPS is damaged, the entire ROPS must be replaced.
WARNING 14 FIRE HAZARDS Use extra care when handling gasoline and other fuels. They are flammable and vapors are explosive. Store all fuel in approved containers specifically designed for that purpose. Allow engine to cool before refueling. Never remove fuel cap or add fuel with engine running.
WARNING 15 FIRE HAZARDS (continued) To prevent fire or explosion, keep sparks and open flames away from battery. Keep electrical connections clean and tight. Inspect them often. Loose connections and corrosion increase fire risk. Before disconnecting the negative ground cable, make sure all switches are off.
WARNING 16 CHILDREN, BYSTANDERS AND PETS Tragic accidents can occur if the operator is not alert to the presence of children, bystanders and pets. Children are attracted to lawn mowers and the mowing activity. NEVER assume children, bystanders and pets will stay where they were last seen.
WARNING 17 SERVICE Never run a mower inside a closed area or without proper ventilation. Keep nuts and bolts tight, especially blade attachment bolts, and keep equipment in good condition. Never tamper with safety devices. Check their proper operation regularly.
18 DIXON ® ZTR ® PRO SERIES COMMERCIAL / RESIDENTIAL W ARRANTY POLICY Black Bear TM , Kodiak ® , Mountain Kodiak ® , Kodiak ® Diesel, Grizzly™ & SilverTip™ DIXON® WARRANTS ITS ZTR® MOWERS AGAINST DEFECTS IN MA TERIAL AND WORKMANSHIP FOR THE PERIODS SET FORTH BELOW .
SPECIFICATIONS 19 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Additional information may be provided elsewhere in this manual. GRIZZLY™ 52 Model 968999588 10 gauge sides with 7 gauge cross members Made of 11 gauge fabricated welded construction with external reinforcement ribs.
SPECIFICATIONS 20 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Additional information may be provided elsewhere in this manual. GRIZZLY™ 60 Model 968999590 10 gauge sides with 7 gauge cross members Made of 11 gauge fabricated welded construction with external reinforcement ribs.
SPECIFICATIONS 21 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Additional information may be provided elsewhere in this manual. GRIZZLY™ 60 Model 968999591 10 gauge sides with 7 gauge cross members Made of 11 gauge fabricated welded construction with external reinforcement ribs.
SPECIFICATIONS 22 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Additional information may be provided elsewhere in this manual. GRIZZLY™ 72 Model 968999592 10 gauge sides with 7 gauge cross members Made of 11 gauge fabricated welded construction with external reinforcement ribs.
23 SEAT ADJUSTMENT INSTRUCTIONS 1. Grasp seat slide adjuster and move it into adjustment position. 2. Slide seat forward or backward. 3. Release seat slide adjuster.
CONTROLS 24 CONTROL LEVERS For access to the seat, move control levers to neutral position and swing them outward. TO GO FORWARD • From neutral position, gently push control levers forward. • To increase speed, move levers further forward. TO GO BACKWARDS • From neutral position, gently pull control levers toward you.
CONTROLS 25 PARK BRAKE The park brake is designed to hold the mower from moving and is not intended for use in stopping the mower while it is in motion. The engine will stop if the park brake is engaged while the control levers are in the drive position.
CONTROLS 26 BLADE DRIVE • Located on the control panel, on operator’s right. • To engage the mower blade, pull up on the switch. • To disengage mower blade, push down. CHOKE AND THROTTLE CONTROL LEVER • Located on control panel to operator’s right.
OPERATION INSTRUCTIONS 27 MOWER DECK CUT HEIGHT LIFT LEVER The lifting lever is used to place the mower deck in the transport position or one of the 18 different cutting heights. The cutting height is set by placing a peg in the hole for the desired cutting height and the peg is then locked on the inside with the supplied pin.
OPERATION INSTRUCTIONS 28 The safe and successful operation of the GRIZZLY will depend on the operator having the correct knowledge of all controls used on the mower and making good judgements about the terrain to be mowed. NEVER allow anyone without complete knowledge of all controls and their functions to operate the mower.
OPERATION INSTRUCTIONS 29 STARTING INSTRUCTIONS 1. Park brake must be on, control levers in outward position with the operator sitting on the seat, and blade drive disengaged. 2. Position throttle to desired speed setting. If engine is cold, position choke lever in the ON position.
OPERATION INSTRUCTIONS 30 TESTING OF SAFETY INTERLOCK SYSTEMS The following tests should be performed at the start of each mowing day. PARK BRAKE SWITCH TEST 1. Swing control levers to outward position. 2. Disengage blade drive. 3. Put park brake in OFF position.
OPERATION INSTRUCTIONS 31 TESTING OF SAFETY INTERLOCK SYSTEMS The following tests should be performed at the start of each mowing day. BLADE DRIVE SWITCH TEST 1. Put park brake in ON position. 2. Swing control levers to outward position. 3. Engage blade drive.
OPERATION INSTRUCTIONS 32 MOWING WITH A MULCHING ATTACHMENT Mulching or recycling the grass clippings requires a totally different mowing approach than would be normal when side discharging or bagging the grass. There may be instances or conditions where it is not possible to hide all the recycled or mulched clippings.
OPERATION INSTRUCTIONS 33 MOWING WITH A MULCHING ATTACHMENT (continued) 7. Keep the underside of the mower deck clean. Remove all grass and dirt buildup from the underside of the pan, the baffles and deflectors after each use.
OPERATION INSTRUCTIONS 34 MOWING WITH A GRASS CATCHER ATTACHMENT In order to achieve optimum performance when mowing with a grass catching attachment, please read and follow the tips listed below. 1. Read and follow the installation instructions that are included with your grass catcher.
OPERATION INSTRUCTIONS 35 7. Maintain sharp blades throughout the cutting season. Some grass catching attachments require a “high-lift” blade. See your dealer for advice on the type of blade(s) needed for your mower.
OPERATION INSTRUCTIONS 36 SIDE DISCHARGE OF THE CLIPPINGS In order to achieve optimum performance when side discharging the grass clippings, please read and follow the tips listed below. Additional information can be found in the Troubleshooting Guide.
OPERATION INSTRUCTIONS 37 GRASS HEIGHT AND CUTTING SUGGESTIONS Do not attempt to cut grass when it is wet. If the grass is tall, place the mower deck cut height lever in the top or second notch. “Initially” overlap cutting swaths instead of a full swath with each pass.
OPERATION INSTRUCTIONS 38 TOWING TRAILERS AND OTHER ATTACHMENTS Towing a trailer or other attachment that is too heavy could damage the drive or cause the mower to become unstable.
CARE AND MAINTENANCE 39 Before performing any maintenance, turn off engine, allow to cool and remove key. Use extreme care when working on machinery. Do not wear watch or jewelry. Do not wear loose fitting clothes, and observe all common safety practices with tools MAINTENANCE SCHEDULE • Adjust traction drive idler .
CARE AND MAINTENANCE 40 CAUTION ! Stop engine and remove ignition key for safety. Wear heavy, thick gloves when holding onto cutter blade, avoid the sharp edge of the blade. CUTTER BLADE MAINTENANCE Check sharpness of mower blades after every 10 hours of operation.
CARE AND MAINTENANCE 41 BELTS Check belts every 100 hours. Replace any belts showing signs of severe cracking or large nicks. Belts are not adjustable, replace if they begin to slip from wear. BELT TENSION Engine to Mower Deck Belt To adjust tension of the mower deck drive belt, turn adjuster nut on threaded eyebolt.
CARE AND MAINTENANCE 42 BATTERY This is a maintenance-free battery and the fluid level cannot be checked. Charge battery if required. OFF SEASON BATTERY STORAGE • DO NOT remove battery from mower. • Clean top of battery and terminals with baking soda and water.
CARE AND MAINTENANCE 43 TIRES Correct tire pressure is essential for efficient operation of the mower. Check tire pressure periodically. Inflate tires to the pressure listed below. Front tires 15 PSI (103 kPa) Rear tires 15 PSI (103 kPa) Lug nuts or lug bolts should be checked regularly for tightness.
CARE AND MAINTENANCE 44 CHANGING THE ENGINE OIL The EZ Drain oil plug is located on the left side of the engine crankcase. 1. Uncap the end of the drain plug and install the oil drain hose. 2. Place a suitable container under the drain hose. 3. To drain, turn the drain plug counter-clockwise to unlatch.
CARE AND MAINTENANCE 45 HYDROSTATIC TRANSMISSION FLUID AND FILTER SERVICE Dirt or water in fluid can ruin the hydrostatic transmissions. SERVICE INTERVALS 1. Initial filter service - 100 hours 2. Every 300 hours or once a year thereafter. MAINTENANCE PROCEDURE Check the fluid level in hydrostatic transmission fluid reservoir daily.
CARE AND MAINTENANCE 46 MOWER DECK LEVELING PROCEDURE There are four (4) eyebolts that will control the attitude or pitch of the mower deck. The deck should be level or pitched slightly higher in rear. 1. Place the mower on a smooth level surface with front casters positioned towards deck.
CARE AND MAINTENANCE 47 ELECTRICAL SYSTEMS Keep all connections clean and tight. CLEANING THE MOWER Wash mower periodically. Clean above and below deck. High pressure washing and alkaline based soaps can cause damage to bearings and other parts of the mower.
48 STANDARD SERVICE PARTS LIST BLADES 52" Deck * Hi Lift Fusion P/N 539 117911 Gator Fusion P/N 539 118035 Hi-Lift P/N 539 118272 Lo-Lift Fusion P/N 539 117973 60" Deck * Hi Lift Fusion P/N .
49 TROUBLESHOOTING 1. ENGINE WON’T TURN OVER Mower blades engaged - - - - - - - - - - - - - - - - - - - - disengage blades Park brake not on - - - - - - - - - - - - - - - - - - - - - - - - engage pa.
50 TROUBLESHOOTING 6. ENGINE RUNS BUT MOWER WON’T MOVE FORWARD Drive belt broken or slipping - - - - - - - - - - - - - - - - - replace drive belt Transmission oil low - - - - - - - - - - - - - - - -.
Dixon ~401 North Commerce Street~Beatrice, NE~68310 ~402-223-1000~Fax 402-223-1053 OWNER’S INFORMATION Date of Purchase ________________________________ Mower Model Number __________________________.
Dixon and ZTR are registered trademarks of Dixon DIXON 401 Commerce Street Beatrice, NE 68310 Grizzly Series Part No. 539 114590R1 WARNING ! The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproduc- tive harm.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Dixon KOH/968999590 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Dixon KOH/968999590 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Dixon KOH/968999590 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Dixon KOH/968999590 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Dixon KOH/968999590, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Dixon KOH/968999590.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Dixon KOH/968999590. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Dixon KOH/968999590 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
