Manuale d’uso / di manutenzione del prodotto D-2400 del fabbricante 3M
Vai alla pagina of 26
# Convenience Store Intercom System Model D-2400 Installation Instructions.
FCC Information This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: • This device must not cause harmful interference. • This device must accept any interference received including interference hat may cause undesired operation.
3M Model D-2400 Front Matter i Revision Record Date Revision Reason For Change 5/00 01 Preliminary manual released. 6/00 02 Incorporated changes from Revision 01.
Front Matter 3M Model D-2400 ii Table of Contents System Components .................................................................................... 1 Component Placement ............................................................................
3M Model D-2400 System Components 1 System Components The 3M™ Model D-2400 Convenience Store Intercom System consists of one of the following components: • Station Selectors • Call Stations • Communcations Controller Figure 1 .
System Components 3M Model D-2400 2 This page intentionally left blank..
3M Model D-2400 Component Placement 3 Component Placement This section describes placement of the 3M™ Convenience Store Intercom System, Model D-2400, components: Communications Controller For proper system operation, locate the Communications Controller: 1.
Component Placement 3M Model D-2400 4 Call Stations For proper system operation, install the Call Stations in locations: 1. Chosen for ease of use. 2. At least 48 inches above the pavement. ü Note Local codes may dictate placement of call stations. Figure 3 .
3M Model D-2400 Wiring the System 5 Wiring the System Depending on distance use twisted pair, 14-22 AWG audio cable when wiring Convenience Store Intercom System, Model D-2400, components. Figure 5 shows an overview of the cable types and number of connectors required for each unit.
Wiring the System 3M Model D-2400 6 Configuration Worksheets Use Configuration Worksheets 1 through 3 (located at the end of this document) to plan and record your system configuration. You can record the system wire locations, wire color scheme, and program settings on the worksheets.
3M Model D-2400 Programming the System 7 Programming the System Program the system to conform to your planned configuration and desired operation. Hardware (Jumpers) Select Call Station(s) to receive ALL CALL and music/messaging during STANDBY mode. (A closed jumper turns ALL CALL and music/messaging OFF.
Programming the System 3M Model D-2400 8 Programming the Selector Programming State 1 2 3 4 5 6 7 8 9 0 MENU T A L K SP-389C Figure 5. D-2400 Keypad To program the D-2400, it is necessary to put the system in the programming state. From this state, the entire system is configured and all memorized parameters are adjusted.
3M Model D-2400 Programming the System 9 Keypad Function Definitions (Programming State) Key functions are defined below. Key Function HOLD (Shift) Shifts between upper and lower case for text data. UP ARROW Increments data by 1. Fields wrap around. DOWN ARROW Decrements data by 1.
Programming the System 3M Model D-2400 10 Key Function 6 Enters the digit 6 for numeric entry. Enters the following for text entry: 7 Enters the digit 7 for numeric entry. Enters the following for text entry: 8 Enters the digit 8 for numeric entry. Enters the following for text entry: 9 Enters the digit 9 for numeric entry.
3M Model D-2400 Programming the System 11 Error Message The system will display one error message: No Communication. The message occurs when there is no communications between the Selector and Controller. To correct this: 1. Be sure Controller is powered on.
Programming the System 3M Model D-2400 12 A value (Off, 1 to 16 inclusive). Priority station #, always moves to top of queue. On or Off. Enables the 30 second station connection time out. Default = On. Assignment of station names 01 through Max Stations where xx indicates station #.
3M Model D-2400 Adjusting the System 13 Adjusting the System Communications Controller You must remove the cover from the Communications Controller to perform the following adjustments. Outbound ALL CALL Volume Level To set the outbound ALL CALL Volume Level: 1.
Adjusting the System 3M Model D-2400 14 Outbound Music/Messaging Level (Only for Systems That Use Music/Messaging) To set the outbound Music/Messaging level, do the following: 1. Ask another attendant to stand near a Call Station that is not in use and has Music/Messaging activated.
3M Model D-2400 Adjusting the System 15 To set the VOX sensitivity level: 1. Follow the directions under the section Programming the Selector to put the Selector in Programming mode. 2. Locate the VOX Enable screen and be sure it is set to ON. 3. Locate the VOX Sensitive screen and press the right-arrow key to edit the value.
Adjusting the System 3M Model D-2400 16 This page intentionally left blank..
3M Model D-2400 Training Users 17 Training Users Train users of the Convenience Store Intercom System, Model D-2400, by performing the following steps: 1. Powering the system up (it should remain on). 2. Answering a call. 3. Initiating a call. 4. Adjusting inbound volume.
Training Users 3M Model D-2400 18 This page intentionally left blank..
3M Model D-2400 Configuration Worksheets 19 Configuration Worksheets.
Configuration Worksheets 3M Model D-2400 20 RECORD SETTINGS AND WIRE COLORS. STORE THIS DOCUMENT IN THE COMMUNICATIONS CONTROLLER. IMPORTANT RECORD WIRE COLORS WIRE COLORS RECORD RECORD WIRE COLORS WIRE COLORS RECORD WIRE COLORS RECORD TO POWER TO ADDITIONAL STATION SELECTORS Max Station Priority Auto Standby (Off, On) (Off, 1, .
3M Model D-2400 Configuration Worksheets 21 RECORD WIRE COLORS RECORD WIRE COLORS WIRE COLORS RECORD WIRE COLORS RECORD MUSIC/MESSAGE TO SOURCE STATION SELECTORS TO ADDITIONAL COMMUNICATIONS CONTROLLER-STATION SELECTOR CONFIGURATION WORKSHEET 3 COMMUNICATIONS CONTROLLER.
3M Food Services Trade Department 3M Center St. Paul, MN 55144-1000 Printed on recycled paper. Printed in U.S.A. © 3M 2001 January 78-6912-0725-8 Rev C.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il 3M D-2400 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del 3M D-2400 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso 3M D-2400 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul 3M D-2400 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il 3M D-2400, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del 3M D-2400.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il 3M D-2400. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo 3M D-2400 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
