Manuale d’uso / di manutenzione del prodotto T-400 del fabbricante Dexter
Vai alla pagina of 34
8 514 - 22 5- 001 REV A page 1 COMMERCIAL WASHER MODEL T- 400 VENDED C- SERIES CONTROL OPERATOR’S MANUAL INSTALLATION & OPERATION INSTRUCTIONS Please read t his infor mation and ret ain for r eference. WARNIN G - THIS WASHER IS EQUIPPED WITH DEVICES AND FEATURES RELATING TO ITS SAFE OPERAT ION.
8 514 - 22 5- 001 REV A page 2 TABLE OF CONTENTS Page No. Wash er Specifications 2 Mounting Dimensions 3 Installation Instructions 4 Operating Instructions 8 Programming the Washer Control 10 Displayed Washer Faults 24 Servicing and Troubleshooting 30 Accessories and Contact Information 34 WASHER SPECIFICATIONS MODEL T-400 30 LB.
8 514 - 22 5- 001 REV A page 3.
8 514 - 22 5- 001 REV A page 4 INSTALLATION INSTRUCTIONS All washers must be installed in accordance with all local, state and national building, electrical, plumbing and other codes in effect in the area. WARNING - THESE INSTALLATION AND SERVI CING INSTRUCTIONS ARE FOR USE BY QUALIFIED PERSONNEL ONLY.
8 514 - 22 5- 001 REV A page 5.
8 514 - 22 5- 001 REV A page 6 PLUMBING Water supply hoses are furnished with each machine. The threaded connections o n the hoses are ¾ -11 ½ NHT. Separate hot and cold water lines must be provided, maintaining 30 psi to 120 psi (207 kPa to 8 27 kPa) water flow pressure.
8 514 - 22 5- 001 REV A page 7 FUSING REQUIREMENTS: SINGLE- and THREE -PHASE 208-240VAC MODELS - 15 AMP TIME-DELAY (DUAL ELEMENT) FUSE (or equivalent circuit breaker) CONTROLS TRANSFORMER The controls transformer is located inside the control trough and steps a range of 208 to 240 volts down to 115 volts.
8 514 - 22 5- 001 REV A page 8 OPERATING INSTRUCTIONS - STARTING THE WASHER A. Load the clothes into the cylinder and latch the door securely. Be sure clothing does not get caught between the door gasket and tub front when closing the door. Maximum load is 30 pounds clothes, dry weight.
8 514 - 22 5- 001 REV A page 9 EMERGENCY STOP / SAFETY DOOR LOCK This machine is equipped with a Safety Door Lock that locks the door closed from when the cycle is started until the cycle is complete. The door lock prevents opening the door for up to 3 minutes if the power is interrupted during the cycle.
8 514 - 22 5- 001 REV A page 10 PROGRAMMING THE WASHER CONTROL The washer control can be programmed to prompt the user for alternate vend prices, change washer cycle times, temperatures and many other options. This can be accomplished in two ways: 1. Manual programming utilizing the “Start”, “Hot”, “Warm” and “Cold” buttons 2.
8 514 - 22 5- 001 REV A page 11 When manual programming mode is entered, the “Start”, “Hot”, “Warm” and “Cold” buttons perform alternate functions.
8 514 - 22 5- 001 REV A page 12 Quick Test Option: When the Quick Test Option is chosen, the washer will begin a shortened wash cycle without the displayed vend price being met. The purpose of this shortened cycle is to test all major components for proper operation.
8 514 - 22 5- 001 REV A page 13 Prices Option: This option allows the user to set values for coin acceptor inputs and to set the vend price. It also allows the user to return the values to factory defaults.
8 514 - 22 5- 001 REV A page 14 Cycles Option: This option allows the user to set the bath time and spin time for the “Wash” bath. It also allows the user to set bath time, water temperature and spin time for “Rinse” and “Final rinse” baths.
8 514 - 22 5- 001 REV A page 15 3. “Delay Spin” is meant to be used in applications where the amount of drain capacity is limited. In these cases the washer cannot empty the tub in sufficient time to allow for a spin cycle to occur.
8 514 - 22 5- 001 REV A page 16 Plus Cycle Options: The “Plus Cycle” options allow for the user to prompt the customer for varying vend prices based on additional wash baths chosen. In general, the user can program the additional wash baths in a similar manner to what was described in the “Cycles” Options section.
8 514 - 22 5- 001 REV A page 17 “Final Rinse” bath. If the customer does not meet the vend price of the “Extra Rinse” feature, the prompt will time out and the “Extra Rinse” bath will not occur.
8 514 - 22 5- 001 REV A page 18 Settings: The “Settings” options allow for the user to make various programming changes to change how the control operation affects the customer.
8 514 - 22 5- 001 REV A page 19 press the “Enter” button to move to the minutes. Once the hours and minute are both chosen, the “Enter” button must be held down for 3 seconds to confirm that RTC is meant to be reset to the complete entry.
8 514 - 22 5- 001 REV A page 20 Usage Menu: The Usage menu allows for the user to track data about machine usage. See below for detailed information on each sub menu option. 1. “Coin Audit”: The coin audit field shows the accumulation of coin pulses that were sent to the control over each of the left and right coin inputs.
8 514 - 22 5- 001 REV A page 21 The figure below shows the sub menu options for U sage:.
8 514 - 22 5- 001 REV A page 22 Control Menu: The Control menu allows for the user to observe important technical information for the control. No changes can be made at this menu. See below for detailed information on each sub menu. 1. “Serial Number”: This is the control seria l number.
8 514 - 22 5- 001 REV A page 23 COIN WASHER DEFAULT CYCLE The following table shows the complete details for the coin washer default cycle. Bath Bath Cycle Time ( min.
8 514 - 22 5- 001 REV A page 24 DISPLAYED WASHER FAU LTS Display ed F ault Code Description DOOR LOCK ERROR Do or Lock Error Condition This error is when th e Door Locked signal i s not received within one se cond after the start of the cycle. A fter three attem pts to start the wa sher.
8 514 - 22 5- 001 REV A page 25 Condition Invalid washer size j umper (harness) configuration. COMM ERROR2 Wrong Wash er Size Jumper Configurati on Delay Immediate (after the wrong size jumpe r configuration is read) . Wash er size /type inputs are rea d only at power up, before star ting a cycl e, once every 24 hours, and in factory test mode.
8 514 - 22 5- 001 REV A page 26 COMM ERROR5 VFD Communication Fault Condition This error is a dat a error on communications between the controller and the V F drive Delay Delay t ime is 12 se conds. Action Stop the machine and clear the cycle. Keep the door lo cked until the machine has stopped moving and then unlock the door.
8 514 - 22 5- 001 REV A page 27 Condition This error is when th e drive si ze does not match the washer size. DRIVE ERROR1 Washer si ze/ VFD size mismat ch Delay Immediate.
8 514 - 22 5- 001 REV A page 28 DRIVE OV VFD Over - voltage Fault Condi tion This error is over - voltage on the VF drive Delay Delay t ime is 35 se conds. Action Stop the machine and clear the cycle. Keep the door locked until th e mac hine h as stop ped m oving and t hen unlock the door.
8 514 - 22 5- 001 REV A page 29 D RIVE GFI VFD Ground Fault Condition This error is a gr ound fault interrupt ion on the VF drive Delay Delay t ime is 12 se conds. Action Stop the machine and clear the cycle. Keep the door locked until th e mac hine h as stop ped m oving and t hen unlock the door.
8 514 - 22 5- 001 REV A page 30 SER VICING AND TROUBLESHOOTING CAUTION: Label al l wires prior to disconnecti on when servici ng control s. Wiri ng errors c an cause improp er an d dang erous opera tion. V erify pr oper o perat ion afte r serv icing. ATTENTION.
8 514 - 22 5- 001 REV A page 31 Door wil l not open Thermoactuator Check t o see i f the rmoactuator and its mech anism are stuck or binding and not allowing the door lock motor to open. Check to be sure that the locking thermoactuator is not r eceiving 120VAC during the last 1 1/2 minute s of the cycle.
8 514 - 22 5- 001 REV A page 32 Water do es not flush softener compartment. Water Val ve Coil Check coil continuity at terminal s and repl ace if no continuit y. Water In let Scr eens Check water in let screens for block age and clean if necess ary. Water Check t o insur e that water is turned on and operat ing.
8 514 - 22 5- 001 REV A page 33 IMPORTANT TRANSIENT VOLTAGE SURGE SUPPRESSORS Like most electrical equipment your new machine can be damaged or have its life shortened by voltage surges due to lightning strikes which are not covered by factory warranty.
8 514 - 22 5- 001 REV A page 34 ACCESSORIES INSTALLATI ON: (Furnished) QTY. 9990 - 027 - 011 Hose, Water Supply 2 8641 - 242 - 000 Washer, Inlet Hose 2 9565 - 003 - 001 Strainer, Inlet Hose 4 Contact distributor or Dexter Laundry, Inc. if a steel-mounting base is required.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Dexter T-400 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Dexter T-400 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Dexter T-400 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Dexter T-400 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Dexter T-400, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Dexter T-400.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Dexter T-400. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Dexter T-400 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
