Manuale d’uso / di manutenzione del prodotto VC36N del fabbricante Desa
Vai alla pagina of 44
DIRECT -VENT FIREPLACE OWNER’S OPERA TION AND INST ALLA TION MANU AL NA TURAL GAS MODELS (V)V C36N AND CGCD V36NR SERIES PROP ANE/LP GAS MODELS (V)V C36P AND CGCDV36PR SERIES Patent Pending For more information, visit www .
www .desatech.com 1 16200-01L 2 SAFETY W ARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property dam - age. Refer to this manual for correct installation and operational proce - dures. For assistance or additional information consult a qualified in - staller , service agency or the gas supplier .
www .desatech.com 1 16200-01L 3 Carbon Monoxide Poisoning: Early signs of carbon monoxide poisoning resemble the u, with headaches, dizziness or nausea. If you have these signs, the replace may not be working properly . Get fresh air at once! Have replace serviced.
www .desatech.com 1 16200-01L 4 2. If you smell gas • shut off gas supply • do not try to light any appliance • do not touch any electrical switch; do not use any phone in your building • immediately call your gas supplier from a neighbor’s phone.
www .desatech.com 1 16200-01L 5 PRODUCT FEA TURES Figure 2 - Common Fireplace Locations Figure 3 - Fireplace Bottom Dimensions D R W FW 29" 41" PRE-INST ALLA TION PREP ARA TION LOCAL CODES Install and use replace with care. Follow all local codes.
www .desatech.com 1 16200-01L 6 • If your replace is to be installed directly on carpeting, vinyl tile or any combustible ma - terial other than wood, it must be installed on a metal or wood panel extending the full widt h and dept h of the repla ce.
www .desatech.com 1 16200-01L 7 PRE-INST ALLA TION PREP ARA TION Continued A B E F G H D C Nailing T abs Figure 4 - Framing Clearances for Installation Against an Exterior Wall 36 1 / 8 " 41 1 / .
www .desatech.com 1 16200-01L 8 Fixed Closed Openabl e Fixed Closed V V V V V V V V X X V X G G J F B B K N H I A N E L D B M A C B V V A G G B TERMINA TION CAP AIR SUPPL Y INLET GAS METE RR ESTRICTED AREA (TERMIN AT ION PROHIBITED) A = clearance above grade, veranda, porch, deck, or balcony [*12" (30.
www .desatech.com 1 16200-01L 9 VENTING INST ALLA TION NO TICE : Fai lur e to foll ow t hese instructions will void the war - ranty . NOTIC E: Do not seal term inatio n cap to vent pipe.
www .desatech.com 1 16200-01L 10 INST ALLA TION PLANNING There are two basic types of direct-vent installation: • Horizontal T ermination • V ertical T ermination Horizontal T ermination Installation IMPORT ANT : Horizontal square terminations require only inner portion of wall restop.
www .desatech.com 1 16200-01L 11 VENTING INST ALLA TION Continued W ARNING: Do not recess vent termination into any wall. This will cause a re hazard. 6. Noncombustible Exterior Wall: Position horizontal vent cap in center of 8 1 / 2 " round hole and attach to exterior wall with four wood screws provided.
www .desatech.com 1 16200-01L 12 VENTING INST ALLA TION Continued Figure 13 - T ypical Horizontal T ermination Cap Mounting with Additional Siding Standoff Installed Siding Standoff Screws High Wind T.
www .desatech.com 1 16200-01L 13 CORNER INST ALLA TION Recommended Applications: • Corner ground oor installation • Ground oor installation where pipe vents horizontally through wall (over 1.
www .desatech.com 1 16200-01L 14 VENTING INST ALLA TION Continued Figure 17 - Horizontal T ermination Conguration for V enting Using Two 90° Elbows 45° Elbow HORIZONT AL SYSTEM INST ALLA TION USING TWO 90° ELBOWS The following congurations show the minimum vertical rise requirements for a horizontal system using two 90° elbows.
www .desatech.com 1 16200-01L 15 INST ALLA TION FOR VERTICAL TERMINA TION Note: V ertical restrictor must be installed in all vertical installations. 1.
www .desatech.com 1 16200-01L 16 5. Place ashing over pipe section(s) ex - te nd in g t hr ou gh ro of . S ec ur e b as e o f ashing to roof and framing with roong nails. Be sure roong material overlaps top edge of ashing as shown in Figure 19, page 15.
www .desatech.com 1 16200-01L 17 VENTING INST ALLA TION Continued Note: V ertical (V 1 ) + Vertical (V 2 ) = 40' max. Figure 23 - V ertical Venting Conguration Using T wo 90° Elbows (V ertica.
www .desatech.com 1 16200-01L 18 P ARTS LIST FOR VENTING KITS AND COMPONENTS DE SA (5 "/8 ") P ipe & V en t K it s Number Description P58-6 6" Section Double W all Pipe, Galvanized .
www .desatech.com 1 16200-01L 19 FIREPLACE INST ALLA TION Blower Location Side View Figure 26 - Blower Model BK Magnetic Strips Exhaust Port Screw Green Ground Wire Spade T erminals Lower Firebox Cavity 6.
www .desatech.com 1 16200-01L 20 CAUTION: Never touch the blower wheel while in operation. 9. Check to make sure that power cord is completely clear of blower wheel and that there are no foreign objects in blower wheel. T urn blower on and check for op - eration.
www .desatech.com 1 16200-01L 21 7. Check to make sure that power cord is completely clear of blower wheel and that there are no foreign objects in blower wheel. Also double check all wire leads and make sure wire routing is not pinched or in a precarious position.
www .desatech.com 1 16200-01L 22 Figure 31 - External Regulator with V ent Pointing Down (Propane/LP Only) Propane/LP Supply T ank CAUTION: Use only new , black iron or steel pipe. Inter - nally-tinned copper tubing may be used in certain areas. Check your local codes.
www .desatech.com 1 16200-01L 23 Figure 33 - Connecting Flexible Gas Line to Millivolt V alve Flexible Gas Line Do NOT Kink Equipment Shutoff V alve T o Gas Supply (Natural) T o External Regulator (Pr.
www .desatech.com 1 16200-01L 24 PRESSURE TESTING FIREPLACE GAS CONNECTIONS 1. Open equip ment shuto ff valv e (see Figu re 34, page 23). 2. Open propane/LP supply tank valve for propane/LP replace or main gas valve located on or near gas meter for natural gas replace.
www .desatech.com 1 16200-01L 25 Installing 9-V olt Alkaline Battery in Hand- Held Remote Control Unit 1. Remove battery cover on back of remote control unit. 2. Attach terminal wires to a 9-volt alkaline battery (not included). Place battery into battery housing.
www .desatech.com 1 16200-01L 26 4. Remount new frame at hinge with 5 new screws before closing door . This will en - sure seating of gasket. 5. Close glass door frame. Lock latches by plac ing bar under tab on door and pushin g down and back on latch (see Figure 42, page 25).
www .desatech.com 1 16200-01L 27 6. Install rear brick panel rst. Rest bottom edge of panel on back edge of burner assembly (see Figure 44). 7. Install left side brick panel by sliding it between burner assembly and side of rebox (see Figure 44).
www .desatech.com 1 16200-01L 28 6. The pilo t is locat ed by the main burne r and should not require accessing for lighting. 7. T urn gas control knob counterclockwise to PILOT (see Figure 45). 8. Push in gas control knob all the way and hold. Immediately light pilot by repeatedly pressing piezo spark ignitor until a ame appears.
www .desatech.com 1 16200-01L 29 OPERA TION Continued ON/OFF SERIES MODEL HRC100 Ho ld th e con tro l b ut to n on th e ha nd -he ld re mo te un ti l bu rne r tu rn s on . Hol d the cont ro l bu tt on again until burner turns off (see Figure 47). TO LOCK press both buttons on hand-held remote control until light stop s ashing.
www .desatech.com 1 16200-01L 30 OPERA TING OPTIONAL GWMT1 - W ALL MOUNTED THERMOST A T W ARNING: Do not con - nect the thermostat to a power source. Electrical shock and/or a re hazard will occur . Light replace as instructed in Lighting In - structions on page 27.
www .desatech.com 1 16200-01L 31 INSPECTING B URNERS Continued BURNER FLAME P A TTERN Burner ames wil l be steady; not lifting or oat - ing. Flame patterns will be dif ferent from unit to unit and will vary depending on installation type and weather conditions.
www .desatech.com 1 16200-01L 32 CAUTION: Wear gloves and safety glasses while handling or removing broken glass. Do not remove if glass is hot. Keep children and pets away from glass. If glass has been broken, carefully remove glass door (see Removing/Replacing Glass Door , page 25).
www .desatech.com 1 16200-01L 33 TROUBLESHOO TING W ARNING: T urn off heater and let cool before servicing. Only a qualied service person should service and repair heater . CAUTION: Never use a wire, needle or similar object to clean pilot. This can damage pilot unit.
www .desatech.com 1 16200-01L 34 OBSERVED PROBLEM Pilot lights but ame goes out when control knob is released Burner does not light after pilot is lit Delayed ignition burner Burner backfiring during combustion Slight smoke or odor during initial operation REMEDY 1.
www .desatech.com 1 16200-01L 35 TROUBLESHOO TING Continued OBSERVED PROBLEM Heater produces a whistling noise when burner is lit Glass soots Fireplace produces a clicking/ ticking noise just after burners are lit or shut off Remote does not function Dark residue on logs or inside of replace REMEDY 1.
www .desatech.com 1 16200-01L 36 TROUBLESHOO TING Continued W ARNING: If you smell gas • Shut off gas supply . • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor ’ s phone.
www .desatech.com 1 16200-01L 37 SPECIFICA TIONS VC36N, VVC36N AND CGCDV36NR • Rating: 22,400/32,000 Btu/hr • Gas T ype: Natural Gas Only • Ignition: Piezo • Manifold Pressure: 3.5" w .c. • Minimum Inlet Supply Pressure: 5.5" w .c.
www .desatech.com 1 16200-01L 38 P ARTS MODELS VC36N, VVC36N, VC36P , VVC36P , CGCDV36NR AND CGCDV36PR SERIES 6 7 22 19 20 15 2 14 21 8 1 4 13 9 16 3 18 5 17 23 10 1 1 12 24 25 26.
www .desatech.com 1 16200-01L 39 P ARTS MODELS VC36N, VVC36N, VC36P , VVC36P , CGCDV36NR AND CGCDV36PR SERIES This list contains replaceable parts used in your replace. When ordering parts, follow the instructions listed under Replacement Parts on page 37 of this manual.
www .desatech.com 1 16200-01L 40 7 15 10 12 1 12 2 3 13 9 1 1 21 22 TPTH TP TH 6 12 14 18 17 17 18 19 20 16 14 8 4 5 P ARTS BURNER ASSEMBL Y MODELS VC36N, VVC36N, VC36P , VVC36P , CGCDV36NR AND CGCDV3.
www .desatech.com 1 16200-01L 41 P ARTS BURNER ASSEMBL Y MODELS VC36N, VVC36N, VC36P , VVC36P , CGCDV36NR AND CGCDV36PR This list contains replaceable parts used in your replace. When ordering parts, follow the instructions listed under Replacement Parts on page 37 of this manual.
www .desatech.com 1 16200-01L 42 MANUAL BLOWER KIT - BK Manual variable control blower accessory provides better heat distribution. C omplete in - stallation and operation instructions included in this manual.
www .desatech.com 1 16200-01L 43 ACCESSORIES Continued RECEIVER AND HAND-HELD THERMOST A T REMOTE CONTROL KIT - HRC200 SERIES Allows the replace to be operated in a manu - ally or thermostatically-controlled mode. Y ou can adjust your heat settings and turn the replace on or off without leaving the comfort of your easy chair .
116200 01 NOT A UPC 1 16200-01 Rev . L 03/08 DESA Heating, LLC 2701 Industrial Drive P .O. Box 90004 Bowling Green, KY 42102-9004 www .desatech.com 1-866-672-6040 WARRANTY KEEP THIS WARRANTY Always specify model and serial numbers when communicating with the factory .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Desa VC36N è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Desa VC36N - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Desa VC36N imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Desa VC36N ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Desa VC36N, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Desa VC36N.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Desa VC36N. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Desa VC36N insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
