Manuale d’uso / di manutenzione del prodotto AP411W del fabbricante Airlink101
Vai alla pagina of 32
Model # AP41 1W User ’ s Manual Ve r. 1 A.
2 Table of Contents Package Cont ent s ......................................................................................................... 3 Introduc tion ..........................................................................................
3 Package Contents • Wireless 108Mbps SuperG Access Point • Power Adapter-DC 5V, 2.0A • Quick Installation Guide • Ethernet Cable • One Set of SMA Antenna If any of the above items are missing, please contact your distributor.
4 Connections LEDs Power : Solid green indicates power is on. LAN : Solid green indicates an established connection. Blinking green ind icates activity on the Ethernet port.
5 Wireless Basics Installation Considerations The 108Mbps SuperG Wireless Access Point lets you access your network, using a wireless connection, from virtually anywhere within its operating range.
6 Connecting the Access Point Step 1 Connect one end of a network cable to the Ethernet port of the access point and connect the other end of the cable to the LAN port of a router.
7 Est ablishing Wireless Connection Below are the default wireless settings of the access point. Y ou must confi gure your wireless network adapter to the same settings in order to establish a wireless connection with the access point.
8 Ste p 2 Right-click on either Wireless Network Connection (if you’re using a wireless card to connect to the AP), or Local Area Connection (if you’re using an Ethernet card to connect to the AP) and click Properties . Ste p 3 Select Internet Protocol (TCP/IP) and click Properties .
9 Step 4 Select Use the following IP address and enter an IP address of 10.0.0.x (where x is any number between 2 - 254 ). Also enter 255.0.0.0 for the Subnet mask and 10.0.0.1 for the Default gateway and click OK . Ste p 5 Clic k Close . Step 6 Open the web browser and type in 10.
10 Ste p 8 T o setup SSID and WEP encryption , click on the Setup Wizard link and click Next . Ste p 9 The default SSID is default and the default channel number is 6 . Y ou may enter any SSID and channel number to match your current wireless network.
11 Step 10 Select to enable or disable WEP encryption and click Next . If you already have WEP encryption enabled for your existing wire less network, you must enter the identical encryption settings here. Ste p 1 1 Click Reboot to save and apply the settings.
12 Web Configuration Utility The Web configuration utility allows you to configure settings for the Access Point. In order to access the web configuration utility, you’ll need to assign a static IP address to your computer.
13 Advanced Setup Use the list on the left side of the screen to navigate to the desired page. Configuration – IP Address MAC Address : Displays the Access Point’s MAC Address. This value cannot be changed. Get IP From-: Select Manual (Static IP) or DHCP (Dynamic IP) as the method you will use to assign an IP address to the Access Point.
14 Default Gateway: This field is optional. If you have a router on your network, enter the IP address of your router. Click Apply to save any changes . Configuration – Device Information Device Type : Displays the factory name for this device. MAC Address : Displays the MAC Address of the Access Point.
15 Configuration – AP Mode Settings Access Point: This is the default setting. It connects the wireless clients to the wired part of your network. PtP Bridge: This mode allows you to connect one Access Point to another Access Point of the same model, bridging two wireless LA Ns together.
16 Configuration – WLAN Parameter Settings Wireless Band: Select to set the signal to 802.11g or 802.11g/802.11b. SSID: The name designated for a specific Wire less Local Area Network (WLAN). The default SSID is default. You can enter any name to match your existing wireless network.
17 Fragment Length: The fragmentation threshold, which is specified in bytes, determines whether packets will be fragmented. Packets exceeding the 2346 byte setting will b e fragmented before transmission. 2346 is the default setting. RTS Length: This value should remain at its def ault setting of 2,346.
18 Configuration – WLAN Partition Wireless Band: Select to set the signa l to 802.11g or 802.11g/802.11b. Internal Station Connection : Check Enabled to allow internal wireless clients to connect to the Access Point. Ethernet to WLAN Access : Check Enabled to allow the wir ed part of your network to connect with the wireless clients.
19 Control: • Disabled : disables the filter function • Accept : only accepts connection from the dev ices whose MAC Address are listed in the Access Control List • Reject : rejects any connection attempts fr om devices whose MAC address are listed in the Access Control List.
20 Key Type : For WEP encryption, select to use HEX (limited to 0-9, A-F) or ASCII (any number or letter). Key Size : 64 Bits : 10 HEX characters or 5 ASCII characters 128 Bits : 26 HEX characters or 13 ASCII characters 152 Bits : 32 HEX characters or 16 ASCII characters Valid Key: Select one key (1st – 4th) to be t he active key.
21 WPA Mode Select WPA as the Authentication and click Apply . Select PSK then enter the pa ss phrase in the Pass Phrase field. Note : Pass phrase must be between 8 – 63 characters in length.
22 Additional WPA settings (RADIUS Server Required) If you have a RADIUS Server in y our network, you may choose to use EAP as the WPA Mode. Domain Name Server IP address: Input the IP address of the DNS server. Domain Name Server: Enter the domain name of the DNS server.
23 Management – Administration User Name: Enter a user name for the login screen; admi n is the default setting. Old Password: To change your password, enter your old password here. New Passw ord: Enter your new password here. Confirm New Password: Enter your new password again for confirmation.
24 Management – Misc Telnet Service : Check Enabled to allow Telnet Service through the Access Point. Timeout : Select the timeout interval. Default is 3 minutes. Click Apply to save any changes . Maintenance – Update Firmware Firmware Version : Displays the current firmware version number.
25 Maintenance – Configuration File You can save your configuratio ns to a file and upload the file later (i.e. after a factory reset so you don’t have to manually reconfigure the settings again). Update File : Browse to a previously saved configuration file and click OK to load the file.
26 Statistics This window displays the statistics of the wireless lo cal area network. Throughput : displays the throughput statistics. Transmitted Frames Count : displays the transmitted frames count.
27 Received Frame Count : displays the received frame count. WEP Frame Error : displays the WEP Frame Error..
28 Troubleshooting This section provides solutions to problems that c an occur during the install a tion and operation of the 108Mbps SuperG Wireless Acce ss Point. We cover variou s aspects of the network setup, including the network adapters. Please read the fo llowing if you are having problems.
29 3. What variables may cause my w ireless products to lose reception? Our wireless products let you access your network from virtually anywhere you want. However, the positioning of the products within your environment as well as the bac kground RF noise will affect the actual wireless range.
30 To hard-reset the 108Mbps Super G Wireless Access Point to the Fa ctory Default Settings, please do the following: A. Locate the Reset button at the back of the 108Mbps SuperG Wireless Access Point. B. Use a paper clip to press the Reset button. C.
31 Technical Specifications Standards IEEE 802.11g IEEE 802.11 IEEE 802.11b IEEE 802.3 IEEE 802.3u Device Management Web-Based Internet Explorer v6 or later; Netscape Navigator.
32 Receiver Sensitivity: 54Mbps OFDM, 10% PER, -68dBm 48Mbps OFDM, 10% PER, -68dBm 36Mbps OFDM, 10% PER, -75dBm 24Mbps OFDM, 10% PER, -79dBm 18Mbps OFDM, 10% PER, -82dBm 12Mbps OFDM, 10% PER, -84dBm 11Mbps CCK, 8% PER, -82dBm 9Mbps OFDM, 10% PER, -87dBm 6Mbps OFDM, 10% PER, -88dBm 5.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Airlink101 AP411W è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Airlink101 AP411W - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Airlink101 AP411W imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Airlink101 AP411W ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Airlink101 AP411W, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Airlink101 AP411W.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Airlink101 AP411W. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Airlink101 AP411W insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
