Manuale d’uso / di manutenzione del prodotto DP350 del fabbricante Delta
Vai alla pagina of 17
INSTRUCTION MANUAL 12" V ariable Speed Drill Pr ess (Model DP350) P ART NO. 905584 - 01-31-03 Copyright © 2003 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury .
3 17. REDUCE THE RISK OF UNINTENTIONAL ST ARTING . Make sure switch is in “OFF” position befor e plugging in power cord. In the event of a power failure, move switch to the “OFF” position. 18. NEVER ST AND ON TOOL . Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted.
A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cords which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug.
Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-pr ong grounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine.
6 DRILL PRESS P AR TS Fig. 1 Fig. 1 1 - Drill Pr ess Head and Motor 2 - Column, Base Flange, and Rack 3 - T able 4 - Base Fig. 2 5 - Chuck 6 - Clamp Handle 7 - Pinon Shaft Handles (3) 8 - T able Raising and Lowering Handle 9 - M8x1.25x125mm Carriage Head Screws (2), 8.
7 FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. 1. Assemble the column (A) Fig. 3, to the base (B) using the four screws, thr ee of which are shown at (C).
8 4. Slide raising rack (F) Fig. 7, table and table bracket onto drill press column, as shown. Make sur e bottom of raising rack (F) Fig. 8, is inside the flange (J) on drill press base. 5. Re-assemble ring (E) Fig. 9, which was removed in STEP 1 . IMPORT ANT : Bottom of ring (E) MUST NOT be pushed all the way down onto top of raising rack (F).
9 7. Thread stud on clamp handle (M) Fig. 12, into hole in rear of table bracket, as shown. 8. Place the drill press head (N) Fig. 13, onto the column as far as it will go. Align head (A) Fig. 13A, to table (B), and base (C). Tighten the two head locking screws (O) Fig.
10 10. IMPORT ANT : Make certain the spindle taper (Q) Fig. 15, and tapered hole in chuck (R) ar e clean and free of any grease, lacquer or rust pr eventive coatings. NOTE: Household oven cleaner can effectively r emove any sub- stance from the spindle and chuck; however , carefully follow the manufacturer's safety rules concerning its use.
11 Fig. 18A FLEXIBLE LAMP The flexible lamp operates independently of the drill press. T o turn the lamp “ON” and “OFF” , rotate switch (A) Fig. 18A. T o reduce the risk of fir e, use 40 watt or less, 120 volt, reflector track type light bulb (not supplied).
12 V ARIABLE SPEED CONTROL T o avoid damaging the drive belts and pulleys, DO NOT turn speed control handles (A) Fig. 24, unless motor is running. The pilot wheel handles (A) are turned clockwise to increase speed and counterclockwise to decrease speed.
13 ADJUSTING SPINDLE RETURN SPRING The spindle is automatically returned to its upper most position when the handle is released. It is r ecommended that the handle be allowed to slowly return to the top position after each hole has been drilled in the material.
14 INST ALLING AND REMOVING DRILL BITS DISCONNECT MACHINE FROM POWER SOURCE. 1. Insert smooth end of drill bit (A) Fig. 29, into chuck (B), as far as it will go, and then back the bit out 1/16", or up to the flutes for small bits. 2. Make certain that the drill bit (A) Fig.
15 LUBRICA TION DISCONNECT MACHINE FROM POWER SOURCE. 1. Remove the six screws (A) Fig. 30 that hold the top cover in place, and remove the top cover . 2. The variable speed pulleys should be oiled weekly with a few drops of light machine oil in the two oil holes (B) Fig.
16 Printed in U.S.A. T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven .
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Delta DP350 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Delta DP350 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Delta DP350 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Delta DP350 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Delta DP350, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Delta DP350.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Delta DP350. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Delta DP350 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
