Manuale d’uso / di manutenzione del prodotto 36-902 del fabbricante Delta
Vai alla pagina of 20
INSTRUCTION MANUAL Unifence™ Saw Guide 30" Capacity (Model 36-902) P ART NO. 422-27-655-0068 - 02-14-03 Copyright © 2003 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 INTRODUCTION The model 36-902, 30" capacity Unifence ™ Saw Guide can be assembled to the, Contractors Saw and Unisaw , in addition to other makes of table saws. The 36-902 Unifence Saw Guide includes the fence, carriage assembly , fr ont guide rail, table frame and legs.
3 Fig. 2 Fig. 3.
4 ASSEMBLING T ABLE TO SA W 1. If your saw has a right extension wing, front and r ear guide rails, they must be removed. 2. Lay the table upside down on the floor or bench, as shown in Fig. 4. 3. Assemble the two table legs (A) Fig. 5 to the bottom of the table using eight #8x7/8" self tapping screws supplied.
5 5. Fasten the front table support (F) Fig. 9, to the bottom of the table as shown using two #8x7/8" long wood screws (H) and (I) supplied. NOTE: The vertical flange, on the table board support (F), should be flush with the front edge of the table board.
6 FOR DEL T A T ABLE SAWS ONL Y 9. Fasten the table adapter plate (B) to the right side of the saw table. Place a 7/16" lockwasher onto a 7/16- 20x1" hex head screw (D), insert scr ew thr ough the table adapter plate and thread scr ew into right side of saw table.
7 Fig. 17 S 13. Using a straight edge (S) Fig. 17, make certain the Unifence table surface is level with the saw table by adjusting two leveling screws located on the bottom of table legs and adjusting angle brackets (B) Fig. 13, use a level, side to side and front to back to make sur e the table is level.
8 ASSEMBLING UNIFENCE GUIDE RAIL TO T ABLE 1. Locate the Guide Rail and mounting hardware fr om the packing material of the Unifence. 2. The guide rail has end caps inserted into each end of the rail.
9 6. Slide the guide rail along until the “0” on the Unifence scale is aligned with the right edge of the saw table. Snug the hex nuts on the saw and extension table but do not tighten at this time. 7. Adjust the guide rail (C) Fig. 25, parallel with the saw table surface.
10 ADJUSTING RAIL STOP 1. The Rail Stop Assembly Fig. 30, can be adjusted to any number of positions along the guide rail providing a quick stop setting for the Unifence body by loosening knob (G) and sliding the stop along the rail to the desired position and re- tighten.
11 ASSEMBLING UNIFENCE BODY TO GUIDE RAIL 1. T ur n fence body (A) Fig. 34, upside down and lay it on a table or bench. Push handle (B) in against fence body . Make certain the surface (C) of clamp bracket is parallel to the face (D) of the fence body , and that the inside edge (E) of the clamp bracket is parallel to surface (F) of the fence body .
12 ASSEMBLING FENCE TO UNIFENCE BODY 1. The fence (A) can be assembled to clamp plate (B) in either the horizontal position as shown in Fig. 38, or the vertical position as shown in Fig. 39. Make certain the two lock knobs (C), are loose and slide fence (A) onto clamp plate (B) as shown.
13 3. When ripping thin stock, it is sometimes more convenient to use the fence in the horizontal position, as shown in Fig. 42. 4. T o move the fence along the guide rail, lift up clamp lever (A), as shown in Fig. 43, slide fence to desired position on the rail, and push down on clamp lever (A) to lock fence in place.
14 Fig. 46 Fig. 47 Fig. 48 Fig. 49 RIPPING WITH THE UNIFENCE Ripping is the operation of making a lengthwise cut through a boar d, as shown in Fig. 46, and the rip fence (A) is used to position and guide the work. One edge of the work rides against the rip fence while the flat side of the board r ests on the table.
15 Fig. 50 Fig. 51 Fig. 52 Fig. 53 ADJUSTING FENCE P ARALLEL TO MITER GAGE SLOTS The fence (A) Fig. 50, should be adjusted so it is parallel to miter gage slots (B). T o check and adjust, move the fence (A) until the bottom front edge of the fence is in line with the edge of the miter gage slot as shown, and push down on fence clamping lever (C).
16 Fig. 54 Fig. 55 Fig. 56 Fig. 58 RIPPING ON LEFT SIDE OF SA W BLADE In some cases it may be desirable to use the fence on the left side of the saw blade.
17 USING AUXILIAR Y WOOD F ACING ON THE UNIFENCE Fig. 59 It is necessary when performing special operations such as when using the moulding cutterhead to add wood facing (A) Fig. 59, to one side of the rip fence as shown. The wood facing is attached to the fence with wood screws thr ough holes drilled in the fence.
18 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT HA.
19 T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in.
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas registradas de POR TER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Delta 36-902 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Delta 36-902 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Delta 36-902 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Delta 36-902 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Delta 36-902, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Delta 36-902.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Delta 36-902. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Delta 36-902 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
