Manuale d’uso / di manutenzione del prodotto 36-312 del fabbricante Delta
Vai alla pagina of 17
INSTRUCTION MANUAL ESP AÑOL: PÁGINA 17 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). 12" Single-Bevel Compound Miter Saw (Model 36-312) Patents Pending P ART NO.
2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
3 GENERAL SAFETY RULES 1. FOR YOUR OWN SAFETY , READ THE INSTRUC- TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly mini- mize the possibility of accidents and injury . 2.
4 ADDITIONAL SAFETY RULES FOR MITER SA WS Refer to them often and use them to instruct others . F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS INJURY . 04-24-03 SA VE THESE INSTRUCTIONS . 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions.
5 Y our new Compound Miter Saw is DOUBLE-INSULA TED to give you added safety . As a result, this saw is equipped with a two-prong plug which permits you to use any conventional 120 volt electrical outlet with concern for maintaining a ground connection.
6 B Fig. 3A A ASSEMBL Y AND OPERA TION Fig. 3 C DA B Fig. 4 A TT ACHING DUST BAG 1. Attach dust spout (A) Fig. 3 to port (B). 2. Depress spring clips (C) Fig. 3 of dust bag (D) and clip dust bag (D) over rib of dust spout (A). MOVING CUTTINGHEAD TO THE UP POSITION Push down on the handle (B) Fig.
7 Fig. 5 A B C E D E Fig.6 FENCE OPERA TION The saw is supplied with left fence segment (A) Fig. 7 that incorporates a squeeze clamp feature. T o operate the fence segment or to slide to another location, squeeze the clamp (A) Fig. 7 to disengage the lock.
8 A B C D E B 1. The compound miter saw will cut any angle from a straight 0° cut to 48° right and left. T urn the locking knob (A) Fig. 13 counterclockwise, depr ess the lock lever (B), and rotate the table to the desired position. 2. This machine is equipped with positive stops at the 0° cut-off position and at the 15°, 22.
9 Fig. 16 C A D B DISCONNECT THE MACHINE FROM THE POWER SOURCE. Fig. 15 T o adjust the sliding fit between the movable table and the base, turn the nut (A) Fig.
DISCONNECT THE MACHINE FROM THE POWER SOURCE. 1. Position the bevel detent plate so that the desired angle (A) Fig. 23 is exposed immediately to the left of the housing (H) Fig. 23. 2. Lift the front handle (A) Fig. 22 to disengage bevel lock. 3. Tilt the cuttinghead left as desired until it stops on plate (A) Fig.
11 DISCONNECT THE MACHINE FROM THE POWER SOURCE. 1. Position the bevel detent plate so that the desired angle (A) Fig. 25 is exposed. 2. Lift the front handle (A) Fig. 26 to disengage the bevel lock. 3. Tilt the cuttinghead left until it stops on the plate (B) Fig.
If the size of the workpiece causes your hand to be inside the table hazard zone (see section “T ABLE HAZARD ZONE” SEE FIG. 21 ), use a clamp to secure the workpiece.
13 Fig. 36 CORRECT CUTTING BOWED MA TERIAL 1. Check the workpiece. If it is bowed, position the workpiece on the table as shown in Fig. 36. 2. When the workpiece is positioned the wrong way (Fig. 37), it will pinch the blade near the completion of the cut.
14 Fig. 42 A MAINTENANCE Disconnect the machine from the power sour ce. Fig. 43 E G C D H Fig. 44 F CHANGING THE BLADE J 1. Use only 12" diameter blades (with 1" arbor holes) that are rated for 5000 RPM or higher . 2. Use the supplied wrench to loosen scr ews (A) Fig.
15 Fig.46 B C Fig. 45 A A BRUSH INSPECTION AND REPLACEMENT Before inspecting brushes, disconnect the machine fr om the power source. Brush life varies, depending on the load on the motor . Check the brushes after the first 50 hours, or after a new set of brushes has been installed.
16 T wo Y ear Limited New Pr oduct W arranty Delta will repair or r eplace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven t.
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas registradas de POR TER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Delta 36-312 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Delta 36-312 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Delta 36-312 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Delta 36-312 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Delta 36-312, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Delta 36-312.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Delta 36-312. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Delta 36-312 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
