Manuale d’uso / di manutenzione del prodotto 36-255L del fabbricante Delta
Vai alla pagina of 25
INSTRUCTION MANUAL ESP AÑOL: PÁGINA 25 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). 12" Compound Laser Miter Saw (Model 36-255L) ™ P ART NO.
2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury .
3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
4 GENERAL SAFETY RULES READ AND UNDERST AND ALL WARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may r esult in electric shock, fire, and/or serious personal injury or pr operty damage.
5 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJURY . 1 . DO NOT OPERA TE THIS MACHINE UNTIL it is assembled and installed according to the instructions. 2. OBT AIN ADVICE from your supervisor, instructor , or another qualified person if you are not familiar with the operation of this machine.
6 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug.
7 EXTENSION CORDS Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-pr ong grounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine.
8 UNP ACKING 1. Carefully r emove the machine from the carton. Retain all packing materials until you have inspected and satisfactorily operated the machine. DO NOT OPERA TE THIS MACHINE UNTIL YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. 2.
9 MOVING T ABLE TO THE 0° CUT -OFF POSITION 1. Rotate locking knob (A) Fig. 6 counter -clockwise as far as it will go. Depress lever (B) and r otate table (C) to the 0 ° straight cut-off position, r elease lever (B), and tighten locking knob (A). 2.
10 4. Attach the fence slide support (E) Fig. 7D, to the extension table (B) by using the two 5/16-18 x1 1/4” long hex head screws, 5/16” lockwashers and 5/16” flat washers (F).
11 Fig. 11 B Fig. 10 A A A A A Fig. 9 F ASTENING MACHINE TO SUPPORTING SURF ACE Before operating your compound miter saw , firmly mount it to a workbench or other supporting surface. Four holes, (A) Fig. 9, are pr ovided for fastening the saw to a supporting surface.
12 Fig. 12 A B Fig. 13 C D E B 1. The compound miter saw will cut any angle fr om a straight 0 ° cut to 47 ° right and left. T urn locking knob (A) Fig. 12 counterclockwise, depr ess lock lever (B), and rotate table to desir ed position. 2. The compound miter saw is equipped with positive stops at the 0° cut-off position and at the 15°, 22.
13 Fig. 15 C B Fig. 16 G F D A Fig. 17 A A ADJUSTING FENCE 90° TO BLADE IMPORT ANT : BEFORE MAKING THIS ADJUSTMENT , SET THE BLADE A T 0° TO THE T ABLE. SEE SECTION “ADJUSTING 0° AND 45° BEVEL POSITIVE STOPS.” 1. DISCONNECT THE MACHINE FROM THE POWER SOURCE.
14 Fig. 20 Fig. 21 B A TIL TING CUTTINGHEAD FOR BEVEL CUTTING IMPORT ANT : MOVE THE SLIDING FENCE TO THE LEFT TO PROVIDE CLEARANCE FOR THE BLADE AND GUARD. THE DEGREES OF TIL T DETERMINES HOW F AR TO MOVE THE SLIDING FENCE. REFER TO THE SECTION “ADJUSTING SLIDING FENCE.
15 Fig. 24 H C B Fig. 25 A Fig. 26 F E Fig. 22 Fig. 23 B A A ADJUSTING CHIP DEFLECTOR 1. DISCONNECT THE MACHINE FROM THE POWER SOURCE. 2. A chip deflector (A) Fig. 22, is supplied to help prevent scrap or cut-of f pieces from entering the upper blade guard.
16 Fig. 27 C A B A C D Fig. 28 Fig. 29 A B C ADJUSTING SLIDING FIT BETWEEN TRUNNION AND BEVEL BRACKET After a long period of time, it may become necessary to adjust the sliding fit between the trunnion and the bevel bracket by tightening the adjusting nut (C), Fig.
17 The T winLaser ™ laser units are mounted in a housing that is fitted into the upper blade guard of the miter saw (Fig. A). The lasers project a beam of light downwar d, along both sides and parallel to the saw blade. This beam of light produces a line- of-cut indicator (a red outline of wher e the saw blade will cut) on the workpiece.
18 LEFT LASER ADJUSTMENT SCREW Fig. H Fig. G Fig. F TO CHECK FOR VERTICAL ALIGNMENT 1. The vertical alignment is set correctly when the lines do not move horizontally (sideways) as the saw head is raised and lowered. If vertical alignment is corr ect jump to “ TO SET LEFT AND RIGHT KERF ADJUSTMENT” .
19 CUTTING ALUMINUM Aluminum extrusions (aluminum screens and storm windows) can easily be cut with your miter saw . When cutting aluminum extrusions, or other sections that can be cut with a saw blade and are within the capacity of the machine, position the material so the blade is cutting through the smallest cr oss-section, as shown in Fig.
20 Fig. 34 Fig. 35 CORRECT INCORRECT Fig. 36 C B A C For support when cutting long pieces, construct a work support extension. Fig. 36 illustrates the miter saw mounted on two standard 2 x 4’ s (A). Fasten the four mounting legs (two of which are shown at (B) Fig.
21 CUTTING CROWN MOULDING One of the many features of the saw is the ease of cutting cr own moulding. The following is an example of cutting both inside and outside corners on 52°/38° wall angle crown moulding. 1. Move the table to the 31.62° right miter position and lock the table in position.
22 Fig. 41 Fig. 42 E B G C A D H Fig. 43 F Fig. 45 B C Fig. 44 A CHANGING THE BLADE USE ONL Y CROSS-CUTTING SAW BLADES. DO NOT USE BLADES WITH DEEP GULLETS AS THEY CAN DEFLECT AND CONT ACT GUARD 1. Use only 12" diameter blades with 1" arbor holes that are rated for 4000 RPM or higher .
23 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air . Clean all plastic parts with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. WEAR SAFETY GLASSES WHILE USING COMPRESSED AIR.
24 NOTES.
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Delta 36-255L è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Delta 36-255L - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Delta 36-255L imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Delta 36-255L ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Delta 36-255L, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Delta 36-255L.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Delta 36-255L. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Delta 36-255L insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
