Manuale d’uso / di manutenzione del prodotto 486.24839 del fabbricante Craftsman
Vai alla pagina of 28
Owner's Manual CRAFTSMAN 40"- 2 STAGE SNOW THROWER TRACTOR ATTACHMENT Model No. 486.24839 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. • Safety • Assembly • Operation • Maintenance • Parts Sears, Roebuck and Co.
ACCESSORIES ........................................................... 2 SAFETY RULES .......................................................... 3 FULL SIZE HARDWARE CHART ................................. 4 CARTON CONTENTS ..........................
Any power equipment can cause injury if operated improperly or if the user does not understand hew to operate the equipment. Exercise caution at all times, when using power equipment. • Read this owner's manual carefully and know how to operate your snow thrower and how to stop the unit and disengage the controls quickly.
SPARE PARTS BAG Store these two bolts and nuts In a safe place until needed. (See page 20.) SHOWN ACTUAL SIZE NOT SHOWN ACTUAL SIZE /CC / FF . EE /oo _ KK REF.
CARTON CONTENTS 1. Cross Brace (Weight Tray) 2. Side Brace (Weight Tray) 3. Right Hand Side Plate (Stamped "R") 4. Left Hand Side Plate (Stamped "L") 5. Anti-rotation Bracket 6. Engagement Rod (Not used on some models) 7. Engine Pulley Keeper 8.
TOOLS REQUIRED FOR ASSEMBLY (2) 7/16" Wrenches (2) 1/2' Wrenches (2) 9/16" Wrenches (2) 3/4" Wrenches (1) Knife ADDITIONAL ITEMS REQUIRED General Purpose Grease ASSEMBLY OF SIDE PLATES TO TRACTOR Right hand (R,H.) and left hand (L.
Assemble a shoulder bolt, a 3/8" lock washer and a 3/8" hex lock nut to the bottom hole in each side plate. See figure 3. Proceed to page 8. 3_" HEX LOCK NUT _8"LOCK WASHER R. H. SIDE PLATE FIGURE 3 3/8" SHOULDER BOLT RIGHT SIDE VIEW Attach the R.
INSTALLING HANGER BRACKETS For better clearance, lower the tractor's suspension arms using the attachment lift lever. On Tractors With Foot Rest Brackets (Figure 7) • Remove the bolt and nut that fasten the L.H. and R.H. foot rest brackets to the frame.
INSTALLING CLUTCH/IDLER ASSEMBLY This section covers the installation of the Clutch/Idler assembly to tractors with attachment clutches that are either rod operated (p, 9), cable operated (p. 10) or electric (p. 12). Use the appropriate instructions for your tractor.
Assemble the short "V" belt onto the engine pulley and then onto the large pulley on top of the clutch/ idler assembly. The belt must be placed to the inside of the engine pulley keeper, the idler pulley and the keeper bolt located beside the large pulley.
Attach the clutch/idler assembly to the tractor frame by sliding the notched arms at the rear of the assembly onto the two shoulder bolts assembled to the inside of the tractor frame. Lift the front of the assembly, fitting the sides into the R.H. and L.
ELECTRIC A'n'ACHMENT CLUTCHES • Turn the clutch/idler assembly upside down and place the extra tensioning chain through the left front hole as shown in figure 19. / TENSIONING CHAIN FIGURE 19 Hook the loose spring through the end of the tensioning chain.
Hold this drawing above you while viewing the Clutch/Idler Assembly from underneath the tractor. Right and left in the drawing will be the reverse of the viewer's right and left. ENGINE Left Side PULLEY of Tractor KEEPER 1/8" HAIRPIN COTTER / IDLER L.
• Tilt the snow thrower back down to the ground. • Remove the nylon tie which fastens the auger drive belt to the discharge housing, leaving the belt assembled around the pulleys. • Remove the nylon tie which fastens the chute crank rod to the crank rod support tube.
A'I-rACHING SNOW THROWER TO TRACTOR NOTE: An additional person's help may be required to mount the snow thrower to the front of the tractor. • Place the tractor and snow thrower on a flat, level surface so that the tractor can be rolled forward to attach the snow blower.
INSTALLING THE ATTACHMENT PIN Lift the front of the snow blower to align the holes in the mounting plates and the side plates. From the left side of the tractor install the attachment pin through the holes, securing it with the 1/8" hairpin cotter.
• Place the plastic keg on the weight tray and fill with approximately 75 Ibs. of dry sand. • Secure the keg with the rubber tarp strap hooked into the holes in the cross brace.
KNOW YOUR SNOW THROWER Read this owner's manual and safety rules before operating your snow thrower, Compare the illustration below with your snow thrower to familiarize yourself with the various controls and their locations.
RAISING AND LOWERING • To raise, push down on the lift handle until the snow thrower locks in the raised transport position. • To lower, push down slightly on the lift handle and pull the trigger. With the trigger pulled, slowly lower the snow thrower until it reaches the ground.
& CAUTION: Before servicing or adjusting the snow thrower, shut off the engine, remove the spark plug wire(s), set the parking brake and remove the key from the tractor ignition. REPLACING AUGER BELT • Disengage the tractor's attachment clutch.
STORAGE RECOMMENDATIONS • Lower the snow thrower to the ground. • Remove the snow thrower from the tractor. • Clean the snow thrower thoroughly. Wash off any salt deposit which may have dried on the thrower and housing. • Any bare metal that has become exposed should be painted or coated with a light oil to prevent rust.
REPAIR PARTS FOR MODEL 486.24839 40" SNOW THROWER 74 17 16 33 ! 8 30 23_- 78 77 28 21 94 19 34 12 21 / 34 31 91 37 98 92 27 21 27 29 21 47 65 9 43 82 65 49 100 25 7 o 49 _ 99 22 95 / 64_ 60 63 45 49 68 .
REF. NO. 1 2 3 4 5 6 7 8 9 !0 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 4O 41 42 43 44 45 46 47 48 49 50 51 52 53 54 REPAIR PARTS FOR MODEL 486.
REPAIR PARTS FOR MODEL 486.24839 40" SNOW THROWER 42 43 4O 47 51 50 I 18 63 53 18 52 74 39 52 26 1_ t f 15 / 69 56 6O 58 6O 1 61 / 81 62 14 57 61 60 18 65 54 6 16 /_ 28 5 31 62 61 / 1 5 73 .
REF. 2 3 4 5 6 8 9 10 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 135 _36 i 37 38 39 40 REPAIR PARTS FOR MODEL 486.24839 40" SNOW THROWER PART NO.
NOTES '26 I.
I 10 ° & CAUTION: DO NOT OPERATE YOUR TRACTOR AND SNOW THROWER ON A SLOPE IN EXCESS OF 10 DEGREES. BE SURE OF YOUR TRACTOR'S TOWING AND BRAKING CAPABILITIES BEFORE OPERATING ON A SLOPE. AVOID ANY SUDDEN TURNS OR MA- NEUVERS WHILE ON A SLOPE.
For in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-HOME" 0-800-469-4663) Para pedir servicio de reparaci6n a domicilio - 1-800-676-5811 In Canada for all your s.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Craftsman 486.24839 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Craftsman 486.24839 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Craftsman 486.24839 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Craftsman 486.24839 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Craftsman 486.24839, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Craftsman 486.24839.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Craftsman 486.24839. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Craftsman 486.24839 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
