Manuale d’uso / di manutenzione del prodotto 315.2696 del fabbricante Craftsman
Vai alla pagina of 22
Owner's Manual 5-1/2 in. PROFESSIONAL CORDLESS TRIM SAW Model No. 315.269600 Save this manual for future reference _, CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co.
• Table of Contents .., .................. '...................................................................................................................... 2 • Warranty and Introduction_ ................................................
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are notsubstitutes for proper accident prevention measures.
RULES FOR SAFE OPERATION (Continued) • MAINTAIN TOOLS WITH CARE. Keep tools sharp at all times, and clean for best and safest performance. Follow instructions for lubricating and changing accessories. • REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before tuming it on.
RULES FOR SAFE OPERATION (Continued) m Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock.
Blade Diameter Blade Arbor Cutting Depth at 0 ° Bevel Cut Cutting Depth at 45 ° Bevel Cut 5-1/2 in. 318 in. 1-9/16 in. 1-1/8 in. No Load Speed Motor Charge Rate Charger Rating 3,800 RPM 14.4 Volts DC 1 Hour 120 volts, 60 Hz, AC Your trim saw has been shipped completely assembled except for the blade.
CHARGER See Figure 2. Your charger has a =.key hole" hanging feature for convenient, space saving storage. Screws should be installed so that center distances are 1-7/16 inches apad. YELLOWANDGREEN LIGHT INDICATE SOFTSTARTMODE GREENLIGHT "ON" REDUGHT"ON"INDICATES FASTCHARGING MODE BATrERY CHARGER BATrERY PACK 1-7/16 in.
KNOW YOUR TRIM SAW See Figure 2. Before attempting to use any tool familiarize yourself with all operating features and safety requirements. Features include easily operated bevel cut and depth of cut adjustment mechanisms; positive O ° bevel stop; spindle lock; and blade wrench storage.
_k WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in .objects being thrown into your eyes, resulting in possible serious injury. _k WARNING: Do not allow familiarity with your trim saw to make you careless.
_i, WARNING: Always remove battery pack from your saw when you are assembling parts, making adjustments, assembling or removing blades, cleaning, or when not in use. Removing battery pack will prevent accidental starting that could cause sedous personal injury.
• Fit saw blade inside lower blade guard and onto spindle. Note: The saw teeth point upward at the front of saw as shown in figure 4. • Replace outer blade washer. • Depress spindle lock button, then mplaoe blade screw. Tighten blade screw securely.
KICKBACK See Figure 7. BLADESET TOO DEEP KICKBACK Fig. 7 The best guard against kickback Is to avoid dangerous Idractlces. Kickback occurs when the blade stalls rapidly and the saw is driven back towards you, Blade stalling is caused by any action which pinches the blade in the wood.
• When making a cut use steady, even pressure. Never force cuts. • Do not cut warped or wet lumber. • Always hold your saw firmly with both hands and keep your body in a balanced position so as to resist the forces of kickback should it occur. When using your saw, always stay alert and exercise control.
TO HELP MAINTAIN CONTROL: • Always support your workpiece near the cut. • Support your workpiece so the cut will be on yo=;r left. • Clamp your workpiece so it will not move during the cut. Place your workpiece with its good side down. Note: The good side is the side on which appearance is important.
TOP VIEW OF SAW GUIDELINE AUGN OUTER BLADE GUIDE NOTCH ON SAW BASE WITH UNE OF CUT AS SHOWN WHEN MAKING CROSS CUTS OR RIP CUTS Fig.16 Since blade thicknesses vary, always make a trial cut in scrap material along a guideline to determine how much, if any, the guideline must be offset to produce an accurate cut.
TO BEVEL CUT The angle of cut of your saw may be adjusted to any desired setting between zero and 50 ° . Note: When making cuts at 50 ° , blade should be set at full depth of cut. When making 45 ° bevel cuts, there is a notch in the saw base to help you line up the blade with the line of cut.
POSITIVE 0 ° BEVEL STOP See Figure 21. ADJUSTMENT BEVEL SCREW ADJUSTMENT KNOB HEX NUT POSITIVE 0 ° BEVELSTOP T COMBINATION SQUARE BLADE • Turn screw and adjust base until square with saw blade. • Tighten hex nut and bevel adjustment knob securely.
18.
,_ WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Avoid using solvents.when cleaning plastic pads. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use.
6 5 CRAFTSMAN CORDLESS TRIM SAW - MODEL NUMBER 315.269600 27 O 12 • _26 14 18 28 19 20 23 10 21 22 [ 24 "2 _ 2_ ' 25 20.
I CRAFTSMAN CORDLESS TRIM SAW- MODEL NUMBER 315.269600 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your CORDLESS TRIM SAW or when ordering repair pads. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS ] Key No.
For in,home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-Home s. (1-800-469-4663) Para peoir servicio de reparacibn a domicilio - 1-800-676-5811 In Canada for all your ser.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Craftsman 315.2696 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Craftsman 315.2696 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Craftsman 315.2696 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Craftsman 315.2696 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Craftsman 315.2696, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Craftsman 315.2696.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Craftsman 315.2696. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Craftsman 315.2696 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
