Manuale d’uso / di manutenzione del prodotto 137.218030 del fabbricante Craftsman
Vai alla pagina of 30
Operator's Manual ® 10 in. TABLE SAW WiTH STAND Model No, 137.218030 CAUTION: Before using this Table Saw, read this manual and follow all its Safety Rules and Operating instructions e Safety In.
SECTION PAGE Warranty ........................................ 2 Product Specifications ....................... 2 Power Tool Safety ............................. 3 Table Saw Safety .................................. 4 Electrical Requirements and Safety .
GENERAL SAFETY iNSTRUCTiONS Read and understand all the instructions below before using the power tool. These safety instructions are not meant to cover every possible condition that could occur. As with any power tool, common sense, vigilance and due care must be used.
2. 3. 4. ALWAYS USE SAW BLADE GUARD, splitter 12. and anti-kickback pawls for every through-sawing operation. Through-sawing operations are those in which the blade cuts completely through the 13. workpiece when ripping or crosscutting. Always be sure blade guard is tightened securely.
GROUNDING iNSTRUCTiONS tN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides a path of least resistance for electric currents and reduces the risk of electric shock. This tool is equipped with an electrical cord that has an equipment-grounding conductor and a grounding plug.
RECOMMENDED ACCESSORIES [_ WARNING I Visit your Sears Hardware Department or see the Craftsman Power and Hand Tools Catalog to purchase recommended accessories for this power tool. [A WARNING I To avoid the risk of personal injury: • Do not use adjustable (wobble) type dadoes or carbide tipped dado blades.
UNPACKING YOUR TABLE SAW A 1 E H G t I o G i O o [1 i [1 [1 P L K M J [1 t.
Blade guard Miter gauge Rip fence _ Table insert Table Left extension fence Blade tilt pointer Blade tilt scale ON/OFF switch with safety key Side table extension Right extension fence Extension fence.
ANTFKICKBACK PAWLS - Prevents the workpiece from being kicked upward or back toward the front of the table saw by the spinning blade. OVERLOAD RESET SWITCH - Resets the thermocouple andprovides a way to restart the saw motor if it overloads or overheats.
ASSEMBLE STAND (FIG. A) 1. Unpack allparts andgroup by type and size (Fig. A). Refer to parts list for quantities. 2. Attach onelong upper support (P)to top of leg(S) using onesquare neck bolt (1)andnut (2). NOTE: • Align detents in stand legwith support brackets to ensure proper fit.
STORAGE (FIG. B=f, FiG. B-2) Rip fence and miter gauge 1. Storage bracket for the rip fence (1) is located on the right side of the stand. 2. Storage bracket for the miter gauge (2) is located on the left side of the stand. Fig. B-f Fig. B-2 -2 MOUNTING SAW ONTO WORK SURFACE (FIG.
RiP FENCE (FIG. F) 1. Thread the fence handle (1) intothecam hole (2) until tight. Secure by tightening the nut (5) against the fence head. 2. Lift upward on the rip fence handle (1) so the rear clamp (3) is fully extended.
BLADE GUARD ASSEMBLY (FIG. J, K, L) 1. Set the blade to maximum height and the tilt to zero degrees on the bevel scale with the hand wheels. Lock the blade bevel lock knob. 2. Place the spring washer (2), flat washer (3), external tooth lock washer (4) onto the blade guard mounting bolt (1)(Fig.
ADJUSTMENT iNSTRUCTiONS [A WARNING I To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is not connected to the power source before making any adjustments. USING THE TABLE EXTENSION FENCE (FIG. N) NOTE: The table extension may be used as side support when cutting large workpieces.
[A WARNING I To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is not connected to the power source outlet. ADJUSTING THE 90 ° AND 45 ° POSITIVE STOPS (FIG. Q, Q-f, R) Your saw has positive stops that will quickly position the saw blade at 90 ° to the table.
ADDITIONAL BLADE ADJUSTMENTS (FIG. T) TOOLS REQUIRED • 10 mm open end or 10mm combination wrench • 4mmhexkey • Framing square • Medium size flat blade screw driver ADJUSTMENT PROCEDURE 1. Turn saw switch OFF and remove plug from the power source.
BASIC SAW OPERATIONS RAISE THE BLADE (FIG, U) To raise or lower the blade, turn the blade elevation handwheel (1) to the desired blade height. NOTE: When sawing, only raise the blade to 1/8 in. higher than the workpiece being cut. Fig. U J 3 TiLTiNG THE BLADE (FIG.
CUTTING OPERATIONS There are two basic types of cuts: ripping and crosscutting. Ripping is cutting along the length and with the grain of the workpiece. Crosscutting is cutting either across the width or across the grain of the workpiece. Neither ripping nor crosscutting may be done safely freehand.
BEVEL RiPPiNG This cutis the same as a rip cutexcept the blade bevel angle is setto an angle other than"0". [_ WARNING I Cut only with the workpiece and the fence on the right side of the blade. [A wARNI.e I Never attempt to pull the workpiece backwards during a cutting operation.
Fig, AA COMPOUND MITER CROSSCUTTING (FIG. BB) 0°~45 ° BLADE BEVEL & 0o~45 ° MITER ANGLE This sawing operation is combining a miter angle with a bevel angle.
DADO CUTS (FIG. EE) [_1_ WARNING I • Only Stackabie dado blades can be used on this SaW, • DO NOT use Adjustable or Wobble type dadoes. • Maximum dado cut width is 1_ in. 1. A dado table insert must be purchased separately for this saw to accept a dado blade.
MAiNTAiNiNG YOUR TABLE SAW GENERAL MAINTENANCE I A WARNING I Before maintaining or lubricating the saw, turn switch off, remove the switch key, and unplug the SaW.
WARNING I To avoid injury from an accidental start, turn the switch OFF remove the switch key and always remove the plug from the power source before making any adjustments, = If for any reason the motor will not run, contact Sears Service Center at 1-800-4-MY=HOME®.
10 in. TABLE SAW MODEL NO. 137.218030 [A WARNING J When servicing use only CRAFTSMAN replacement parts. Use of any other parts many create a HAZARD or cause product damage. Any attempt to repair or replace electrical parts on this Table Saw may create a HAZARD unless repair is done by a qualified service technician.
10 in. TABLE SAW MODEL NO. 137.218030 SCHEMATIC 0LMG J // / 267K2 KCY4 0J764 2F96 OGIU4 / Oqq 0B2C _/ OKA4 2 O JET 0B3R 0B9M6 0J9H 6 oBgc _OKRQs 0K25 27X7 2FGZ 0J76 / _0BPA _,OSTQ OKQJ OSGC )KMS I < OKJO_ OJED AU_ "_'J 2"_NJ.
10 in. TABLE SAW MODEL NO. 137.218030 PARTS LiST AND SCHEMATIC FOR MOTOR I. D. NO. Description 0HX9 NEEDLE BEARING 0JX3 HEX. SOC. SET SCREW 0K3A CR. RE.
10 in. TABLE SAW PARTS LiST AND SCHEMATIC FOR STAND MODEL NO. 137.218030 I. D. NO. Description 09D6 FOOT PAD 0BBN HOOK 0EB2 LONG BOTTOM SUPPORT BRACKET 0EBB SHORT BOTTOM SUPPORT BRACKET 0J4F FLAT WASHER 0g4g FLAT WASHER 0JPC HEX. HD. BOLT 0JPP HEX. HD.
PUSH STICK CONSTRUCTION This is a full-size drawing (actual size) Use good quality plywood or solid wood Use 1/2 in. or 3/4 in. material Push stick MUST be thinner than the width of material being cut / / / / Drill Hole For Hanging / Notch To Prevent Hand From Slipping i / / / / / / Cut Here To Push 3/4 in.
.
Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold itt For the replacement parts, accessories and owner's manuals that you need to do-it-yourself.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Craftsman 137.218030 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Craftsman 137.218030 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Craftsman 137.218030 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Craftsman 137.218030 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Craftsman 137.218030, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Craftsman 137.218030.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Craftsman 137.218030. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Craftsman 137.218030 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
