Manuale d’uso / di manutenzione del prodotto 5600 del fabbricante Coleman
Vai alla pagina of 44
Gas Barbecue Use, Car e & Assembly Manual W ith Grill Lighting Instructions 5600 LP Gas Series 5610 Natural Gas Series ASSEMBLER/INST ALLER: Leave these instructions with the consumer . CONSUMER/USER: Read all instructions and keep in a safe place for future r eference.
2 DANGER • FOR OUTDOOR USE ONL Y . NEVER operate grill in enclosed areas, as this could lead to gas accumulating from a leak, causing an explosion or a carbon monoxide buildup which could result in injury or death. DO NOT use in garages, breezeways, sheds or any enclosed area.
1 3 2 36" 8 7 36" (90cm) 36" (90cm) 36" (90cm) Clear REPRESENT A TIVE ILLUSTRA TION • Installation must conform with local codes or , in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1 (USA), CAN/CGA-B149.
4 Longer detachable power-supply cords or extension cords must be used with care. The marked electrical rating of the cord set or extension cord must be at least as great as the electrical rating of the appliance. If the appliance is of the grounded type, the exten- sion cord should be a grounding-type 3-wire cord.
5 DANGER • DO NOT insert any foreign object s into the valve outlet. Y ou may damage the valve. A damaged valve can cause a leak, which could result in explosion, fire, severe per- sonal injury or death.
W ARNING Handle a full cylinder with care. Gas is under high pressure. DANGER • NEVER store a spare L.P . gas supply cylinder under the grill body or inside grill enclosure or in the vicinity of any heat producing appliance. (Fig. 12) • NEVER fill the cylinder beyond 80% full.
Assembly/Set up ■ Remove components from p ackage. Firebox Cart S pacer Right Side T able Left Fryer Assembly Grates Burner Heat T ents™ Center Base Cart S pacer Left Panel Left Door Right Door Gr.
Ö Ö NOTE: Use a large piece of cardboard or a ground cloth to protect the painted finish on the grill. Ö Ö NOTE: The base pieces are assembled up-side- down in this step. Step 1 1-A Center Base Right Base Lef t Base (TN) M6 x 15mm Screw (8) Qty . Hardware shown actual size 1-B 1-B .
Ö Ö Carefully turn the assembly Right-Side-Up. Ö Ö Engage the Locking Casters to prevent movement during the rest of the assembly process. Step 2 9 2-A 2-B 2-A . Assemble the Cylinder Retaining Bolt to the Cylinder Support. (VP) Self T apping Screw (1) Qty .
Ö Ö Assemble two Cart Spacers to the Grill Cart. Step 4 10 4-A . Assemble two Cart Spacers between the Left and Right Panels using eight Screws (TN). Ö Ö NOTE: The Cart Spacers are identical. Assemble one vertically and one hori- zontally . Ö Ö Tighten all fasteners.
Step 5 11 5-A . Assemble two Rear Panels to the cart assem- bly using eight Screws (TN). Ö Ö NOTE: The Rear Panels are identical. Ö Ö Align the square holes on the Rear Panel with the tabs and push down to install the panels. Ö Ö Tighten all fasteners.
7-A Grill Cart Firebox Ö Ö Assemble Firebox to the Grill Cart. Ö Ö NOTE: A second person is needed when aligning the Firebox to the Grill Cart. Step 7 7-A . Carefully place the Firebox onto the Cart Assembly . Do not damage the Electrical Wires (see Fig.
Ö Ö Fasten the Firebox to the Grill Cart. NOTE: In Fig. 8-A and 8-B, the Cart Spacer is not illustrated. Step 8 13 8-A Hardware shown actual size (TN) M6 x 15mm Screw (4) Qty . (DY) M6 Flat W asher (4) Qty . Flange on Right Side Panel Flange on Firebox Firebox TN (x2) DY (x2) 8-B 8-A .
Ö Ö NOTE: The Grill Lids should be opened for Step 9. Ö Ö Assemble Right Side T able to the Grill. Step 9 9-A 9-B 9-C 9-A . Raise the Grill Lids. Ö Ö Place the Right Side T able against the Firebox and on top of the Right Rear Panel. Hardware shown actual size (TN) M6 x 15mm Screw (4) Qty .
15 Ö Ö Assemble Right Side T able to the Grill (continued). Step 10 10-A 10-B View of Grill from Rear 10-C 10-D TN (x2) 10-A . LOOSEL Y assemble two additional Screws (TN) and two Flat W ashers (DY) through the Firebox into the Right Side T able at the rear of the grill.
Ö Ö NOTE: The Grill Lids must be opened for Step 1 1. Ö Ö Assemble Left Fryer Assembly to the Grill. Step 11 1 1-A 1 1-B 1 1-C 1 1-A . Raise the Grill Lids. Ö Ö Place the Left Fryer Assembly against the Firebox and on top of the Left Rear Panel.
17 Ö Ö Assemble Left Fryer Assembly to the Grill (continued). Step 12 12-A 12-B View of Grill from Rear 12-C 12-D 12-A . LOOSEL Y assemble two additional Screws (TN) and two Flatwashers (DY) through the Firebox into the Left Fryer Assembly at the rear of the grill.
Ö Ö Assemble the Fuel Hose Fitting from the Grill to the Fryer Assembly . Step 13 13-A Fuel Hose from Fryer Assembly 13-A . Assemble the Fuel Hose Fitting from the Grill to the Fryer Assembly . 13-B . Retract the Collar on the Quick Coupler before insert- ing the Male Hose Fitting.
Ö Ö Assemble the Electrode Wire to the Electrode T ip on the Side Fryer . Ö Ö Assemble the Grease Pan below the Fryer Burner . Step 14 14-A 14-A . Attach the Electrode Wire to the Electrode T ip on the Side Fryer . Electrode Tip Route the Electrode Wire through the slot in the Fryer Panel.
Ö Ö Assemble Front Fryer Heat Shield. Step 15 15-A 15-A . Assemble Fryer Heat Shield. Ö Ö NOTE: Place the Fryer Heat Shield between the Fryer Panel and the Flexible Fuel Hose. Do not pinch Electrode Wire. Ö Ö Engage the two tabs on the Heat Shield downward into the rectangle holes.
Ö Ö Route the Electrical Wires under the Right Side T able. Ö Ö Note the location of the Electrode Module. Step 16 16-A 16-B 16-C 16-A . Route the Back Burner Electrical Wire through the Wire Support. Electrical Wire Wire Support Electrode Module Back Burner Electrical Wire 16-D Wire Tie Electrical Wire 16-C .
Ö Ö Assemble the electrode Wires and the Battery to the Electrode Module. Step 17 17-A Electrode Module Igniter Button Wires (Note: Large T abs) 9-V olt Battery T EST THE I GNITER : A SP ARK SHOULD APPEAR A T ELECTRODE TIP . I F THE SP ARK DOES NOT APPEAR : -C HECK THE WIRE CONNECTIONS TO THE MODULE .
Ö Ö Fasten the Rear T rim Plate to the Grill Cart. (VP) Self T apping Screw (2) Qty . Hardware shown actual size 18-A 18-A . Fasten the Rear T rim Plate to the Firebox with two Screws (VP). Ö Ö NOTE: Route Electrical Wire through notch. Do not pinch wire .
19-A Hardware shown actual size (XR) M5 x 15mm Flat Head Screw (8) Qty . Ö Ö Fasten both Left and Right Doors to the Grill Cart. Ö Ö Attach the T ool Hook to the Right Door . 19-B . Fasten the Right Door to the Grill Cart with four Flat Head Screws (XR).
20-A Ö Ö Fasten the Door Handles to the Doors. Ö Ö Attach the T ool Hook to the Right Door . Ö Ö NOTE: M4 x 5mm Screws are factory installed into the Handles. Step 20 Hardware shown actual size (EZ) M4 X 5mm Screw (4) Qty . EZ (x2) DOOR HANDLE RIGHT DOOR 20-A .
21-B 21-C . Install four Cooking Grates with smooth surface down. Ö Ö Locate the Power Grates in the center positions. 21-C 21-B . Install four Heat T ents™ over the Burners. Ö Ö The Heat T ents™ are located using the alignment pins. 21-D . Place the W arming Racks in the back of the Firebox.
Ö Ö Assemble two Grease Cup Supports to the Grease Pan. Note: The Grease Pan is shown up-side-down during this step. 23-A (VP) Self T apping Screw (4) Qty . Hardware shown actual size VP (x4) Grease Cup Support Note: Lip is up. 23-A . Attach the Grease Cup Support to the Grease Pan with two self-tapping screws (VP).
Ö Ö Assemble the Motor Mount Bracket to the right outside of the Firebox. Ö Ö Assemble the Rotisserie to the Firebox. Step 25 Hardware shown actual size (TN) M6 x 15mm Screw (2) Qty .
25-E Push Button to Remove Rotisserie Handle 25-E . Remove Handle immediately after placing Rotisserie into the Firebox. Damage will occur if the Handle is not removed prior to cooking. CAUTION • DO NOT OPERA TE THE GRILL WITH THE ROTISSERIE HANDLE ON THE SPIT ROD.
Ö Ö Attach an LP Cylinder to the Grill. 26-A Cylinder Support LP Cylinder 26-A . Set LP Cylinder in the Cylinder Support with the outlet valve facing toward the front of the grill. 26-B 26-B . T ighten the Cylinder Retainer Bolt against the bottom cylinder collar .
Ö Ö NOTE: Step 27 applies to you only if your grill is set up from the factory to use NA TURAL GAS. If your grill is set up from the factory to use LP GAS, skip back to Step 26. Step 27 P LACE THE RUBBER PLUG ONT O THE GAS SUPPL Y LINE . T HEN A TT ACH THE SOCKET END OF THE QUICK DISCONNECT COUPLING ONTO THE GAS SUPPL Y LINE .
1. Check that the cylinder valve is closed by turning the cylinder knob clockwise to a full stop. 2. Check that all the grill burner knobs are in the off position. 3. Remove the protective caps from the cylinder valve and cou - pling nut. NOTE: The coupling nut connect s to the large outside threads on the valve outlet.
CAUTION Inspect the gas supply hoses before each use. If there are cuts, damage, excessive abrasion or wear , replace the hoses prior to operating the appliance.
Lighting Main Burners CAUTION DO NOT touch hot grill p arts with bare hands! Y ou MUST use protective gloves. CAUTION Be certain the gas is shut of f at the L.P . cylinder valve anytime the grill is not in use. 1. T urn all burner control knob(s) to off.
Good Bad Y ellow Blue Holes in Burner Y ellow Blue 21 Grilling T ips and Hints Follow These Step s: 1. Shut of f gas at the burner valve(s) and stay away! 2. Allow the fire to burn itself out. 3. Once the fire is out and the appliance has cooled, shut of f the L.
Step s For Cleaning V enturi: 1. Remove burner from grill bottom. 2. Look inside lower end of venturi tubes for nests, webs or mud. 3. T o remove the above obstructions, use an accessory flexible venturi brush or bend a small hook on one end of a 20-inch- long flexible wire such as the one shown in Fig.
CAUTION A collision with the grill, as with any metal object, could cause injury . Use care when moving a port able gas grill. W ARNING If the grill is not in use, the gas MUST be turned of f at the fuel supply cylinder . Moving and Storage T roubleshooting DANGER NEVER attempt to operate your grill without orifices in the valves.
TYPE 1 CONNECTION ILLUSTRA TION Thermal Sensitive Handwheel 1-5/16" Acme Connection Nipple with Excess Flow V alve Regulator For Y our Additional Safety DANGER If a fire occurs at the cylinder valve, DO NOT attempt to move the cylinder . IMMEDIA TEL Y call the fire department and clear the area.
Please do not send other correspondence to the address belo w. PRODUCT REGISTRA TION DEP ARTMENT PO BO X 2931 WICHIT A ,KS 67201 A TTN: DEPT 586 IMPOR T ANT! Coleman ¨ Grill W arranty Registration Ca.
7) Side burner (if applies) 8) Steamer/Fryer/W ar mer (if applies) 9) Side table design 10) Color of the grill (not including stainless steel) 11) Warming racks 12) Dependable igniter 13) Size of the .
41 Recipes Spice-rubbed sp areribs Cooking time: 45 minutes to partial boil; 16-20 min- utes to grill 6 pounds baby back pork spareribs water to cover For the spice mixture: 2 Tb brown sugar 3 Tb papr.
42 Recipes Asian-flavored eggplant Cooking time: 8-10 minutes 2 large eggplant, peeled and sliced into 1/2 inch rounds 2 Tb olive oil For the sauce: 1 tsp grated ginger 3 cloves minced garlic 4 green onions, sliced thin 2 Tb soy sauce 1 Tb hoisin sauce 2 tsp sugar juice of one lime 2 Tb sesame oil Heat the left griddle to high, with the lid of f.
Recipes 43 Lamb grilled with rosemary and Dijon Cooking time after marination: 30-40 minutes 2 pound boneless lamb leg, trimmed and butterflied 8 cloves garlic, minced 2 tsp fresh rosemary leaves, min.
The Coleman Co., Inc. • 3600 N. Hydraulic • Wichita, KS 67219 U.S.A. 1-800-835-3278 • TDD: 316-832-8707 9990-050 (1 1/24/03) © 2003 The Coleman Company , Inc. All rights reserved. Coleman ® is a registered trademark of The Coleman Comp any , Inc.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Coleman 5600 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Coleman 5600 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Coleman 5600 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Coleman 5600 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Coleman 5600, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Coleman 5600.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Coleman 5600. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Coleman 5600 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
