Manuale d’uso / di manutenzione del prodotto KGT-12-T del fabbricante Cleveland Range
Vai alla pagina of 25
SE95010 Rev . 9 Operators Manual Installation, Operation & Service Gas T able T op Kettles MODELS : KGT -6-T KGT -12-T 1333 East 179th S t., Cleveland, Ohio, U.S.A. 441 10 Phone: (216) 481-4900 Fax: (216) 481-3782 Visit our web site at www .clevelandrange.
FOR THE USER IMPOR T ANT POST IN A PROMINENT LOCA TION, INSTRUCTIONS T O BE FOLLOWED IN THE EVENT THE USER SMELLS GAS. THIS INFORMA TION SHALL BE OBT AINED BY CONSUL TING YOUR LOCAL GAS SUPPLIER. KEEP APPLIANCE AREA FREE AND CLEAR FROM COMBUSTIBLES. DO NOT OBSTRUCT THE FLOW OF COMBUSTION AND VENTILA TION AIR.
INSPECTION Before unpacking visually inspect the unit for evidence of damage during shipping. If damage is noticed, do not unpack the unit, follow shipping damage instructions. SHIPPING DAMAGE INSTRUCTIONS If shipping damage to the unit is discovered or suspected, observe the following guidelines in preparing a shipping damage claim.
Installation must be in accordance with local codes and/or the National Fuel Gas Code ANSI Z223.1 Latest Edition (USA) or the latest Installation Codes for Gas Burning Appliances and Equipment CAN/ CGA B149.1 and CAN/ CGA B149.2 (Canada). Use a gas pipe joint compound which is resistant to L.
6 7 8 5 4 3 2 1 9 OPERA TING INSTRUCTIONS ITEM # DESCRIPTION FUNCTION 1. Tilting Handle Used for tilting the kettle. 2. V acuum/Pressur e Gauge Indicate steam pressur e in PSI inside steam jacket as well as vacuum in inches of mercury .
OPERA TING THE KETTLE DO NOT A TTEMPT TO OPERA TE THIS APPLIANCE DURING A POWER F AILURE. KEEP APPLIANCE AND AREA FREE AND CLEAR OF COMBUSTIBLES. DO NOT LEAN ON OR PLACE OBJECTS ON KETTLE LIP . SERIOUS INJURY COULD RESUL T IF KETTLE TIPPED OVER, SPILLING HOT CONTENTS.
MARINE LOCK Y our unit is equipped with a marine lock to prevent accidental tilting. The following procedur e should be used to tilt the kettle. 1. Grasp the tilt handle. 2. Hold the latch down to unlock tilting mechanism. 3. Pull the handle to tilt kettle.
ST AINLESS STEEL EQUIPMENT CARE AND CLEANING (Suppied courtesy of Nafem. For more information visit their web site at www .nafem.org) Contrary to popular belief, stainless steels ARE susceptible to rusting. Corrosion on metals is everywhere. It is r ecognized quickly on iron and steel as unsightly yellow/orange rust.
SER VICE P AR TS W ARRANTY Our Company supports a worldwide network of Maintenance and Repair Centers. Contact your nearest Maintenance and Repair Centre for r eplacement par ts, service, or informati.
CONSOLE COMPONENTS (used after J une 2005) ITEM # P ART # DESCRIPTION QTY . 1. KE600545 COMPONENT MOUNTING BRACKET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. KE50753-7 RELA Y . . . . . . . . . . . . . . . . . . . . . . . . . .
CONSOLE COMPONENTS (used prior to June 2005) ITEM # P ART # DESCRIPTION QTY . 1-8 KE01928-3 COMPONENT PLA TE ASSEMBL Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 1. KE01927-2 COMPONENT MOUNTING PLA TE WELDMENT . . . . . .
O VERHEAD VIEW 3 2 1 ITEM # P ART # DESCRIPTION QTY . 1. F A21024 HEX NUT , SS, 5/16-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. F A31030 HELICAL SPRING LOCK W ASHER, SS, 5/16" DIA. . . . . . . .
SWITCHES & INDICA TORS (used after J une 2005) KE600560-B 2 3 5 6 7 8 9 1 4 10 OFF 4 1 2 5 6 3 ITEM # P ART # DESCRIPTION QTY . 1. KE55486-3 INDICA TOR LIGHT , GREEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.
SWITCHES & INDICA TORS (used prior to June 2005) 5 6 5 4 2 3 1 8 5 7 ITEM # P ART # DESCRIPTION QTY . 1. SE00114 POTENTIOMETER WITH ON/OFF SWITCH, C/W ITEM #2 . . . . . . . . . . . . . . . . .1 2. KE51005 ROT ARY SEAL . . . . . . . . . . . . . . .
1 2 3 5 6 17 1 8 19 SEE FAUCET DRAWING 20 21 2 8 25 26 27 2 8 4 22 2 3 24 7 8 ITEM # P ART # DESCRIPTION QTY . 1. SK50403 BRONZE BEARING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. SK50434 W ASHER .
PIPING ASSEMBL Y T O MAIN GA S S UPPL Y 14 5 6 2 1 4 3 11 10 8 1 3 16 17 7 9 15.
ITEM # P ART # DESCRIPTION QTY . 1. KE01929-1 FEED PIPE ASS'Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. KE55240-8 GAS V AL VE, NA TURAL . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleveland Range equipment requir es little preventative maintenance. We do however pr ovide the following chart as a guideline for inspection and maintenance to keep your unit functioning at 100%. INSPECTION AND MAINTENANCE CHECK LIST The following check should be completed every six months or more frequently if unit is in a high volume facility .
CALIBRA TING PROCEDURE 1. Insure the unit has a vacuum befor e you begin calibrating procedur es. If unit requires venting r efer to Kettle V enting Instructions. 2. Set On-Off Switch/T emperature Control to " 10 " ( Max.). 3. Allow the unit to cycle twice.
RESERVOIR FILL PROCEDURES The kettle's water level must be maintained at the proper level. Under normal operating conditions, the sealed water reservoir should never r equire the addition of water .
KETTLE JACKET CLEANOUT AND P ASSIV A TION PROCEDURES The following procedur e should be preformed at least once ever y three years to pr event possible corrosion and ensure the optimum life of the kettle. DESCRIPTION - Molyfilm 315 inhibits corrosion in stainless steel and copper .
KETTLE VENTING INSTRUCTIONS 1. T urn kettle ON and set T emperatur e Control to 10 (Max.), heat the empty kettle until unit cycles off. 2. V ent kettle by pulling safety valve ring 8-10 times in short 2-3 second blasts with a 5 second interval between pulls.
WIRING DIAGRAM 4 4 10 13 11 15 3 14 12 5 1 2 8 8 9 6 7 ITEM # P ART # DESCRIPTION 1. KE55486-2 L.E.D., RED (USED AFTER JUNE 2005) KE50567-1 L.E.D., RED (USED PRIOR TO JUNE 2005) 2 KE55486-3 L.E.D., GREEN (USED AFTER JUNE 2005) . KE50567-3 L.E.D., GREEN (USED PRIOR TO JUNE 2005) 3.
OPERA TING SEQUENCES 1. T urn On-Off Switch/ * 14 volt transformer is energized and powers solid state control system. T emperatur e Control Knob "ON" * T emperature knob is turned up and control box calls for heat. * Relay (R Y -1) closes and powers 24 volt transformer .
MARINE LOCK TESTING PROCEDURE 1. Check that lock clears stop pin on side box without rubbing when kettle is tilted (Figure A ). 2. Check side to side play . Lock should remain fully over stop pin when pushed to it's maximum side to side play (Figure B ).
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Cleveland Range KGT-12-T è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Cleveland Range KGT-12-T - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Cleveland Range KGT-12-T imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Cleveland Range KGT-12-T ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Cleveland Range KGT-12-T, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Cleveland Range KGT-12-T.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Cleveland Range KGT-12-T. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Cleveland Range KGT-12-T insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
