Manuale d’uso / di manutenzione del prodotto AIRCAP702IAK9 del fabbricante Cisco Systems
Vai alla pagina of 26
G ETTING S TARTED G UIDE Cisco Aironet 700 Series Access Points June 2013 1 About this Guide 2 Introduction to the Access Point 3 Safety Instructi ons 4 Unpacking 5 Configuratio ns 6 Access Point Port.
2 1 About this Guide This Guide provides in structions on how to install and conf igure your Cisco Aironet 700 Seri es Access Point. The 700 Series Access Point is referred to as the 700 series or the access point in this document.
3 War n in g IMPORT ANT SAFETY INSTRUCTIONS This warning symbol means d anger . Y ou are in a situation that could cause bod ily injury . Before you work on any equipment, be aware of the hazards invo lved with electrical circuitry and be familiar with standard practices for preventing accidents.
4 4 Unpacking T o unpack the access point , follow these steps: Step 1 Unpack and remove the access point and the accessory kit from the shipp ing box. Step 2 Return any pa cking material to the shippi n g container and save it for future use. Step 3 V erify that you have received the items lis ted below .
5 Figur e 1 Access P oint LED Indicator (t op) The ports and connections on the side of the access point are shown in Figure 2 . 1 LED indicator 347756 1.
6 Figur e 2 Access P oint P orts and Connection s (bot tom) 7 Configuring the Access Point This section describes how to connect the access point to a wir eless LAN controller . Because th e configuration process takes place on the co ntroller , see the Cisco Wireless LAN Controller C onfiguration Guide for additional information.
7 The Controller Discovery Process The access point uses standard Control and Provisioning of Wireless Access Points Protocol (CAPW AP) to communicate between the controller and other wireless access points on the network.
8 Preparing the Access Point Before you mount and deploy your access poin t, we recommend that you perform a site su rvey (or use the site planning tool) to determine the best location to install your access point. Y ou should have the following in formation about your wireless network available: • Access point locations.
9 Figure 3 Pr e-Installat ion Configuration Setup T o perform pre-installation con figuration, perform the following steps: Step 1 Make sure that the Cisco wireless LAN controller DS port is connected to the n etwork.
10 e. If the operating system download is successful, the access point reboots. Step 3 Configure the access point if required. Use the contro ller CLI, controller GUI, or Cisc o Prime Infrastructure to customize the access-point-spe cific 802.11n network settings.
11 10 Troubleshooting If you experience difficulty getting your access point installe d a nd running, look for a solution to your problem in this guide or in additional access point documentation. These, an d other documents, are available on Cisco.com.
12 Troubleshooting the Ac cess Point Join Process Access points can fail to join a controller for many reasons: a RADIUS authorization is pending; self-signe d certificates are n ot enabled on the controller; the access point’ s a nd controller’ s regu latory domains don’t match, and so on.
13 An access point sends all syslo g messages to IP address 255.255.255.255 b y default when any of the following conditions are met: • An access point running software release 5.2 or later has been newly deploy ed. • An existing access point running softw are release 5.
14 Manufacturer: Cisco Systems, Inc. 170 W est T asman Drive San Jose, CA 95134-1706 USA This device complies with Part 15 rules. Operation is subject to the followin g two conditions: 1.
15 Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Aironet a ccess po ints in Ja pan.
16 English Translation When installing the product, please use the provid ed or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire.
17 European Community, Switzerland, Norway, Iceland, and Liechtenstein Models: AIR-CAP702I-E-K9 AIR-SAP702I-E-K9 Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medica.
18 The following standards were applied: EMC—EN 301.489-1 v1.8.1; EN 301.489-17 v2.1.1 Health & Safety—EN60950-1: 2005; EN 50385: 2002 Radio—EN 300 328 v 1.7.1; EN 301.893 v 1.5.1 The conformity assessment procedure referr ed to in Article 10.
19 Generic Discussion on RF Exposure The Cisco products are designed to comply with the following na tional and international standard s on Human Exposure to Radio F requencies: • US 47 Code of Federal Regulations Pa rt 2 Subpart J • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers / IEEE C 95.
20 This Device Meets the In dustry Canada Guidelines fo r Exposure to Radio Waves The 700 series device includes a radio transmi tter and receiver . It is designed not to exceed the limits for exposure to ra dio waves (radio frequency electromagnetic fields) as refer e nced in Health Canada Safety Code 6.
21 Chinese Translation English Translation Administrative Rules for Low- power Radio-Frequency Devices Article 12 For those low-power radio-frequency de vices that have alre ady received a type-approv al, companies, business units or users should not change its frequencies, increase its power or change its original features a nd functions.
22 Chinese Translation English Translation Low-power Radio-frequency Devices T echnical Spec ifications 4.7 Unlicensed National Information Infrastructure 4.7.5 Within the 5.25-5.35 GHz band, U-NII devices will be restricted to indoor operation s to reduce any potential for harmful inte rference to co-cha nnel MSS operations.
23 Operation of Cisco Aironet Access Points in Brazil This section contains special information for ope ration o f Cisco Aironet access points in Bra zil.
24 Step 2 Create the DHCP pool, including the ne cessary parameters such as default r outer and name server . A DHC P scope example is as follows: ip dhcp pool <pool name> network <IP Network.
25 14 Obtaining Documentation and Submitting a Service Request For information on obtaining documentati on, submitting a service request, and gathering additional information, see What’ s New in Cisco Product Documentation at: http://www .cisco.com/en/US/docs/general/wha tsnew/whatsnew .
26 Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries . To vie w a list of Cisco t radem arks, go to this URL: www.cisco.com/go/trademarks . Third-party trademarks mentioned are the property of their re spective owners.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Cisco Systems AIRCAP702IAK9 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Cisco Systems AIRCAP702IAK9 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Cisco Systems AIRCAP702IAK9 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Cisco Systems AIRCAP702IAK9 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Cisco Systems AIRCAP702IAK9, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Cisco Systems AIRCAP702IAK9.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Cisco Systems AIRCAP702IAK9. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Cisco Systems AIRCAP702IAK9 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
