Manuale d’uso / di manutenzione del prodotto 2010 Malibu del fabbricante Chevrolet
Vai alla pagina of 444
2010 Chevrolet Malibu Owner Manual M In Brief ................ .......... ........... ....... 1 - 1 I n s t r u m e n t P a n e l ... .............................. 1 - 2 Initial Drive Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 V ehicle Features .
2010 Chevrolet Malibu Owner Manual M Service and Appearance Care . . . . . . . . . . . . . . . . . . . 6-1 S e r v i c e .................................... ....... 6 - 3 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL MOTORS, GM, the GM Emblem, CHEVROLET , the CHEVROLET Emblem, the MALIBU Emblem, and the name MALIBU are registered trademarks of General Motors. This manual describes features that may or may not be on your specific vehicle either because they are options that you did not purchase or due to changes subsequent to the printing of this owner manual.
Safety W arnings and Symbols W arning messages found on vehicle labels and in this manual describe hazards and what to do to avoid or reduce them. Danger indicates a hazard with a high level of risk which will result in serious injury or death. W arning or Caution indicates a hazard that could result in injury or death.
V ehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. 9 : Airbag Readiness Light # : Air Conditioning ! : Antilock Brake System (ABS) g : Audio Steering Wheel Controls or OnStar ® $ : Brake System Warning Light " : Charging System I : Cruise Control B : Engine Coolant T emperature O : Exterior Lamps # : Fog Lamps .
2 NOTES vi.
Section 1 In Brief Instrument Panel ................................... 1-2 Initial Drive Information .. ....... .................. 1-4 Remote Keyless Entry (RKE) System . . . . . . . . . . . 1-4 Remote V ehicle Start . . . . . . . . . . . . . . . . .
Instrument Panel 1-2.
A. Outlet Adjustment on page 4 ‑ 25 . B. T urn Signal/Multifunction Lever on page 4 ‑ 4 . C. Driver Shift Control (If Equipped). Automatic T ransmission Operation (Six Speed T ransmission) on page 3 ‑ 25 or Automatic T ransmission Operation (Four Speed T ransmission) on page 3 ‑ 28 .
Initial Drive Information This section provides a brief overview about some of the important features that may or may not be on your specific vehicle. For more detailed information, refer to each of the features which can be found later in this owner manual.
When the vehicle starts, the parking lamps will turn on and remain on as long as the engine is running. The doors will be locked and the climate control system may come on. The engine will continue to run for 10 minutes. Repeat the steps for a 10-minute time extension.
Windows On vehicles with power windows, the switches are on the driver door armrest. Each passenger door has a switch that controls only that window . Press the front of the switch to open the window . Pull the switch up to close it. For more information, see Power Windows on page 3 ‑ 15 .
Power Seats (If Equipped) Move the seat forward or rearward by moving the control forward or rearward. Raise or lower the front or rear of the seat by moving the front or rear of the control up or down. See Power Seats on page 2 ‑ 5 . Power Reclining Seatbacks (If Equipped) T o raise or recline the seatback, tilt the top of the control forward or rearward.
Power Lumbar Adjustment Press the front (A) or rear (B) of the control to increase or decrease lumbar support. See Power Lumbar on page 2 ‑ 5 . Second Row Seats Either side of the rear seatback can be folded down for more cargo space. With the front seatbacks in the fully upright position, lower the rear seatback by pulling up on the seatback strap while folding the seatback down.
Heated Seats On vehicles with heated front seats, press the top of the switch to turn the heat feature on to the high heat setting. The indicator light (2) will be lit. Press the top of the switch again to go to the low heat setting. The indicator light (1) will be lit.
Sensing System for Passenger Airbag The passenger sensing system will turn off the right front passenger frontal airbag under certain conditions. The driver airbags are not affected by this. The passenger airbag status indicator will be visible on the instrument panel when the vehicle is started.
Keep the selector switch in the center position when not adjusting either outside mirror . Manually fold the mirrors inward to prevent damage when going through an automatic car wash. T o fold, push the mirror toward the vehicle. Push the mirror outward, to return to its original position.
Interior Lighting Dome Lamps The dome lamps come on when any door is opened. They turn off after all the doors are closed. T o turn the dome lamps on manually , turn the instrument panel brightness knob, located on the instrument panel to the left of the steering column, clockwise to the farthest position.
For more information, see: . Headlamps on page 4 ‑ 10 . . Delayed Headlamps on page 4 ‑ 1 1 . . Daytime Running Lamps (DRL) on page 4 ‑ 1 1 . . Automatic Headlamp System on page 4 ‑ 1 1 . . Fog Lamps on page 4 ‑ 12 . Windshield Wiper/W asher The windshield wiper lever is located on the right side of the steering column.
Climate Controls Climate Control System A. Fan Control B. Air Recirculation C. T emperature Control D. Outside Air E. Air Delivery Mode Control F . Air Conditioning G. Rear Window Defogger Automatic Climate Control System (If Equipped) A. Fan Control B.
V ehicle Features Radio(s) Radio with CD (MP3) and USB Port shown O : Press to turn the system on and off. Turn to increase or decrease the volume. BAND: Press to choose between FM, AM, or XM ™ , if equipped. f : Select radio stations. © ¨ : Seek or scan stations.
Setting the Clock T o set the time and date for the Radio with CD (MP3) and USB port or Radio with a Single CD (MP3) player: 1. T urn the ignition key to ACC/ACCESSORY or ON/RUN. 2. Press O to turn the radio on. 3. Press H and the HR, MIN, MM, DD, YYYY (hour , minute, month, day , and year) displays.
Steering Wheel Controls If equipped, some audio controls can be adjusted using the controls on the right side of the steering wheel. e + / e − : Increases or decreases volume. w / x : Press to change radio stations, select tracks on a CD, or to select tracks and navigate folders on an iPod ® or USB device.
Driver Information Center (DIC) The DIC display is located at the bottom of the instrument panel cluster . It shows the status of many vehicle systems and enables access to the personalization menu. The DIC buttons are located on the left side of the steering wheel.
Cruise Control The cruise control buttons are located on the left side of the steering wheel. J : On/Off. RES+: Press to resume or accelerate speed. SET − : Press to set or decrease speed. For more information, see Cruise Control on page 4 ‑ 7 . Power Outlets Accessory power outlets can be used to connect auxiliary electrical equipment, such as a cellular telephone.
Performance and Maintenance T raction Control System (TCS) The traction control system limits wheel spin. The system turns on automatically every time the vehicle is started. . T o turn off traction control, press and release t on the instrument panel.
Tire Pressure Monitor This vehicle may have a T ire Pressure Monitor System (TPMS). The T ire Pressure Monitor alerts you when a significant reduction in pressure occurs in one or more of the vehicle ’ s tires by illuminating the low tire pressure warning light on the instrument cluster .
Resetting the Oil Life System 1. T urn the ignition to ON/RUN, with the engine off. 2. Press and hold the DIC INFO and reset buttons, on the left side of the steering wheel, at the same time to enter the personalization menu. The OIL LIFE RESET message displays.
Roadside Assistance Program U.S.: 1-800-CHEV -USA (1-800-243-8872) TTY Users: 1-888-889-2438 Canada: 1-800-268-6800 As the owner of a new Chevrolet, you are automatically enrolled in the Roadside Assistance program. This program provides technically trained advisors who are available 24 hours a day , 365 days a year , minor repair information or towing arrangements.
Crisis Assist, Stolen V ehicle Assistance, V ehicle Diagnostics, Remote Door Unlock, Roadside Assistance, T urn ‐ by ‐ T urn Navigation and Hands ‐ Free Calling are available on most vehicles. Not all OnStar services are available on all vehicles.
OnStar Steering Wheel Controls This vehicle may have a T alk/Mute button that can be used to interact with OnStar hands-free calling. See Audio Steering Wheel Controls on page 4 ‑ 84 for more information. On some vehicles, the mute button can be used to dial numbers into voice mail systems, or to dial phone extensions.
2 NOTES 1-26.
Section 2 Seats and Restraint System Head Restraints ............................... ..... 2-2 Front Seats ......................................... 2-4 Manual Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Power Seats .
Head Restraints The front seats have adjustable head restraints in the outboard seating positions. { W ARNING: With head restraints that are not installed and adjusted properly , there is a greater chance that occupants will suffer a neck/spinal injury in a crash.
Pull the head restraint up to raise it. T o lower the head restraint, press the button, located on the top of the seatback, and push the restraint down. Push down on the head restraint after the button is released to make sure that it is locked in place.
Front Seats Manual Seats { W ARNING: Y ou can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Power Seats If the vehicle has power seats, the controls used to operate them are located on the outboard side of the seats. T o adjust the seat: . Move the seat forward or rearward by sliding the control forward or rearward. . Raise or lower the front part of the seat cushion by moving the front of the control up or down.
Heated Seats On vehicles with heated front seats, press the top of the switch to turn the features on to the high heat setting. The indicator light (2) will be lit. Press the top of the switch again to go to the low heat setting. The indicator light (1) will be lit.
T o recline the seatback: 1. Lift the recline lever . 2. Move the seatback to the desired position, then release the lever to lock the seatback in place. 3. Push and pull on the seatback to make sure it is locked. T o return the seatback to an upright position: 1.
{ W ARNING: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job. In a crash, you could go into it, receiving neck or other injuries.
Power Lift Seat T o adjust a power lift seat, press the top or bottom of the power lift seat switch to raise or lower the seat. Rear Seats Split Folding Rear Seat With this feature, either side of the seatback can be folded down for more cargo space. Before folding a seatback, make sure the front seat is not reclined.
T o lower the rear seatback, pull up on the seatback strap while folding the seatback down. This allows access to the trunk. T o raise the rear seatback pull the seatback up and make sure it latches. Push and pull on the seatback to be sure it is locked in position.
Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly . It also describes some things not to do with safety belts. { W ARNING: Do not let anyone ride where a safety belt cannot be worn properly .
In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: Y ou never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive.
Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 2-13.
The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... 2-14.
or the safety belts! With safety belts, you slow down as the vehicle does. Y ou get more time to stop. Y ou stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: Y ou could be — whether you are wearing a safety belt or not.
Q: If I am a good driver , and I never drive far from home, why should I wear safety belts? A: Y ou may be an excellent driver, but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers.
Sit up straight and always keep your feet on the floor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt.
Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way . { W ARNING: Y ou can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury .
Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way . { W ARNING: Y ou can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Q: What is wrong with this? A: The belt is buckled in the wrong buckle. { W ARNING: Y ou can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Q: What is wrong with this? A: The belt is over an armrest. { W ARNING: Y ou can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { W ARNING: Y ou can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury .
Q: What is wrong with this? A: The belt is behind the body . { W ARNING: Y ou can be seriously injured by not wearing the lap-shoulder belt properly . In a crash, you would not be restrained by the shoulder belt. Y our body could move too far forward increasing the chance of head and neck injury .
Q: What is wrong with this? A: The belt is twisted across the body . { W ARNING: Y ou can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly , or ask your dealer/retailer to fix it.
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. The following instructions explain how to wear a lap-shoulder belt properly . 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. T o see how , see “ Seats ” in the Index.
4. If equipped with a shoulder belt height adjuster , move it to the height that is right for you. Improper shoulder belt height adjustment could reduce the effectiveness of the safety belt in a crash. See “ Shoulder Belt Height Adjustment ” later in this section for instruction on use and important safety information.
Shoulder Belt Height Adjuster Y our vehicle has a shoulder belt height adjuster for the driver and right front passenger position. Adjust the height so that the shoulder portion of the belt is centered on the shoulder . The belt should be away from the face and neck, but not falling off of the shoulder .
Rear Safety Belt Comfort Guides This vehicle may have rear shoulder belt comfort guides. If not, they are available through your dealer/ retailer . The guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults.
2. Place the guide over the belt and insert the two edges of the belt into the slots of the guide. 3. Be sure that the belt is not twisted and it lies flat.
{ W ARNING: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy .
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle's safety belts. The manufacturer's instructions that come with the booster seat state the weight and height limitations for that booster .
Q: What is the proper way to wear safety belts? A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs.
{ W ARNING: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly . In a crash, the child would not be restrained by the shoulder belt.
Infants and Y oung Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
{ W ARNING: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 40 km/h (25 mph), a 5.5 kg (12 lb) infant will suddenly become a 1 10 kg (240 lb) force on a person's arms.
{ W ARNING: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle's owner , are available in four basic types. Selection of a particular restraint should take into consideration not only the child's weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Child Restraint Systems A rear-facing infant seat (A) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. A forward-facing child seat (B) provides restraint for the child's body with the harness.
Securing an Add-On Child Restraint in the V ehicle { W ARNING: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Secure the child restraint properly in the vehicle using the vehicle's safety belt or LA TCH system, following the instructions that came with that child restraint and the instructions in this manual.
A label on your sun visor says, “ Never put a rear-facing child seat in the front. ” This is because the risk to the rear-facing child is so great, if the airbag deploys. { W ARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates.
Configurations for Use of Child Restraints A. Child restraint using LA TCH B. Child restraint or occupant using safety belt A. Occupant prohibited B. Child restraint using LA TCH A. Child restraint using LA TCH B. Child restraint or occupant using safety belt C.
Lower Anchors and T ethers for Children (LA TCH) The LA TCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier . The LA TCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LA TCH system.
T op T ether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash.
Lower Anchor and T op T ether Anchor Locations Rear Seat i (T op T ether Anchor): Seating positions with top tether anchors. j (Lower Anchor): Seating positions with two lower anchors. T o assist you in locating the lower anchors, each rear anchor position has a label, near the crease between the seatback and the seat cushion.
The top tether anchors are located under the covers, behind the rear seat, on the filler panel. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed. Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top tether must be attached.
{ W ARNING: Do not attach more than one child restraint to a single anchor . Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose or even break during a crash. A child or others could be injured.
A. Passenger Side Rear Seat Lower Anchors B. Center Rear Seat Lower Anchors C. Driver Side Rear Seat Lower Anchors Make sure to attach the child restraint at the proper anchor location. This system is designed to make installation of child restraints easier .
2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor , if equipped. Refer to the child restraint instructions and the following steps: 2. 1. Find the top tether anchor .
If the position you are using has an adjustable headrest or head restraint and you are using a dual tether route the tether under the headrest or head restraint and in between the headrest or head restraint posts. See Head Restraints on page 2 ‑ 2 .
3. Push the latch plate into the buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary . 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
5. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor . When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
A label on the sun visor says, “ Never put a rear-facing child seat in the front. ” This is because the risk to the rear-facing child is so great, if the airbag deploys. { W ARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates.
Y ou will be using the lap-shoulder belt to secure the child restraint in this position. Follow the instructions that came with the child restraint. 1. Move the seat as far back as it will go before securing the forward-facing child restraint. When the passenger sensing system has turned off the right front passenger frontal airbag and seat-mounted side impact airbag, the off indicator on the passenger airbag status indicator should light and stay lit when you start the vehicle.
5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor .
If a child restraint has been installed and the on indicator is lit, see “ If the On Indicator is Lit for a Child Restraint ” under Passenger Sensing System on page 2 ‑ 66 for more information. T o remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position.
Here are the most important things to know about the airbag system: { W ARNING: Y ou can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Airbags are designed to work with safety belts, but do not replace them.
{ W ARNING: Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle's safety belt system nor its airbag system is designed for them.
Where Are the Airbags? The driver's frontal airbag is in the middle of the steering wheel. The right front passenger's frontal airbag is in the instrument panel on the passenger's side.
Driver Side shown, Passenger Side similar The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door . Driver Side shown, Passenger Side similar The roof-rail airbags for the driver , right front passenger, and second row outboard passengers are in the ceiling above the side windows.
{ W ARNING: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating airbag must be kept clear . Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other airbag covering.
Frontal airbags may inflate at different crash speeds. For example: . If the vehicle hits a stationary object, the airbags could inflate at a different crash speed than if the vehicle hits a moving object. . If the vehicle hits an object that deforms, the airbags could inflate at a dif ferent crash speed than if the vehicle hits an object that does not deform.
What Makes an Airbag Inflate? In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inflator . Gas from the inflator fills the airbag causing the bag to break out of the cover and deploy . The inflator , the airbag, and related hardware are all part of the airbag module.
What Will Y ou See After an Airbag Inflates? After the frontal airbags and seat-mounted side impact airbags inflate, they quickly deflate, so quickly that some people may not even realize an airbag inflated. Roof-rail airbags may still be at least partially inflated for some time after they deploy .
{ W ARNING: A crash severe enough to inflate the airbags may have also damaged important functions in the vehicle, such as the fuel system, brake and steering systems, etc. Even if the vehicle appears to be drivable after a moderate crash, there may be concealed damage that could make it difficult to safely operate the vehicle.
Passenger Sensing System The vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator will be visible on the instrument panel when the vehicle is started. United States Canada The words ON and OFF , or the symbol for on and off, are visible during the system check.
A label on the sun visor says, “ Never put a rear-facing child seat in the front. ” This is because the risk to the rear-facing child is so great, if the airbag deploys. { W ARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates.
When the passenger sensing system has turned off the right front passenger frontal airbag and seat ‐ mounted side impact airbag, the off indicator will light and stay lit to remind you that the airbags are off. See Passenger Airbag Status Indicator on page 4 ‑ 29 .
If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. T urn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.
If the Off Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat. If this happens, use the following steps to allow the system to detect that person and enable the right front passenger frontal airbag and seat-mounted side impact airbag: 1.
Additional Factors Affecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “ Safety Belts ” and “ Child Restraints ” in the Index for additional information about the importance of proper restraint use.
Servicing Y our Airbag-Equipped V ehicle Airbags affect how the vehicle should be serviced. There are parts of the airbag system in several places around the vehicle. Y our dealer/retailer and the service manual have information about servicing the vehicle and the airbag system.
Adding Equipment to Y our Airbag-Equipped V ehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Y es. If you add things that change your vehicle's frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly .
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly . Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job.
Replacing Restraint System Parts After a Crash { W ARNING: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. T o help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
2 NOTES 2-76.
Section 3 Features and Controls Keys ........................... ..................... 3-3 Remote Keyless Entry (RKE) System . . . . . . . . . . . 3-4 Remote Keyless Entry (RKE) System O p e r a t i o n ................... ............... ... 3 - 4 Remote Vehicle Start .
Section 3 Features and Controls Universal Home Remote System .. ....... ....... 3-38 Universal Home Remote System Operation (With Three Round LED) . . . . . . . . . . . . . . . . . . . . 3-39 Storage Areas . . . . . . . . . . . . . . . . . . . . . . .
Keys { W ARNING: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window .
Remote Keyless Entry (RKE) System See Radio Frequency Statement on page 8 ‑ 20 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/21 1 of Industry Canada. Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment.
Q (Lock): Press to lock all the doors. The interior lamps turn off after all of the doors are closed. If enabled through the Driver Information Center (DIC), the remote lock feedback can be programmed to have the horn chirp and/or the turn signals flash to confirm locking.
Programming T ransmitters to the V ehicle Only RKE transmitters programmed to the vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/ retailer . When the replacement transmitter is programmed to the vehicle, all remaining transmitters must also be programmed.
Remote V ehicle Start Y our vehicle may have a remote starting feature that allows you to start the engine from outside the vehicle. It may also start the vehicle's heating or air conditioning systems and rear window defogger . When the remote start system is active and the vehicle has an automatic climate control system, it will automatically regulate the inside temperature.
T o manually shut off a remote start, do any of the following. . Aim the RKE transmitter at the vehicle and press and release the remote start button. . T urn on the hazard warning flashers. . T urn the ignition switch out of LOCK/OFF position and then back to LOCK/OFF .
Doors and Locks Door Locks { W ARNING: Unlocked doors can be dangerous. . Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked.
Power Door Locks With power door locks, the switches on the front doors can be used to lock and unlock the vehicle. " (Unlock): Press to unlock the doors. Q (Lock): Remove the key from the ignition and press to lock the doors. Door Ajar Reminder A chime will sound and the DOOR AJAR message will display if one of the doors is not fully closed.
Rear Door Security Locks The vehicle has rear door security locks to prevent passengers from opening the rear doors from the inside. Open the rear doors to access the security locks on the inside edge of each door . T o set the locks, insert a key into the slot and turn it to the horizontal position.
T runk Press the trunk release button on the Remote Keyless Entry (RKE) transmitter for one second to open the trunk from the outside. { W ARNING: Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate.
Remote T runk Release Press the button located on the driver door near the map pocket to open the trunk. The trunk can only be opened while the vehicle is in P (Park) or when the ignition is off. T runk Assist Handle There is an assist handle located on the inside of the trunk.
Emergency T runk Release Handle Notice: Do not use the emergency trunk release handle as a tie-down or anchor point when securing items in the trunk as it could damage the handle. The emergency trunk release handle is only intended to aid a person trapped in a latched trunk, enabling them to open the trunk from the inside.
Power Windows The power window switches are located on the armrest on the driver's door . In addition, there is a switch on each passenger door . Express-Down Window The driver window has an express-down feature. This switch is labeled AUTO. Press the front all the way down and release, to automatically lower .
Express-Up Window On windows with this feature, pull the switch up to the second position and release the switch to activate the express-up feature. T o stop the window as it is going up, pull up or press down briefly on the switch again. Programming the Power Windows If the battery on the vehicle has been recharged, disconnected, or is not working, the driver power window will need to be re-programmed for the express-up feature to work.
Window Lockout The driver power window controls also include a lockout button. o (Window Lockout): Press the lockout button to stop the rear passengers from using their window switches. The driver and front passenger can still operate all the windows with the lock on.
The security light, located on the instrument panel cluster , comes on to indicate that arming has been initiated. Once the system is armed, the security light flashes once every three seconds. If the security light is flashing twice per second, this means that a door is open.
P ASS-Key ® III+ Electronic Immobilizer See Radio Frequency Statement on page 8 ‑ 20 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/21 1 of Industry Canada. P ASS-Key ® III+ Electronic Immobilizer Operation Y our vehicle has P ASS-Key ® III+ (Personalized Automotive Security System) theft-deterrent system.
T o program the new key: 1. V erify that the new key has a 1 stamped on it. 2. Insert the already programmed key in the ignition and start the engine. If the engine will not start, see your dealer/retailer for service. 3. After the engine has started, turn the key to LOCK/OFF , and remove the key .
Ignition Positions The ignition switch has four different positions. T o shift out of P (Park), the ignition must be in ON/RUN or ACC/ACCESSORY and the brake pedal must be applied. Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key .
Retained Accessory Power (RAP) These vehicle accessories can be used for up to 10 minutes after the engine is turned off: . Audio System . Power Windows . Heated Seats (if equipped) . Sunroof (if equipped) These features continue to work up to 10 minutes after the ignition is turned to LOCK/OFF .
2. If the engine does not start after 5 ‐ 10 seconds, especially in very cold weather (below 0°F or − 18°C), it could be flooded with too much gasoline. T ry pushing the accelerator pedal all the way to the floor and holding it there as you hold the key in ST ART for up to a maximum of 15 seconds.
T o Use the Engine Coolant Heater 1. T urn off the engine. 2. Open the hood and unwrap the electrical cord. On the 2.4L engine, the engine coolant heater cord is located near the air cleaner box on the passenger side of the engine compartment. On the 3.
Automatic T ransmission Operation (Six Speed T ransmission) The automatic transmission has a shift lever located on the console between the seats. P (Park): This position locks the front wheels. It is the best position to use when you start the engine because the vehicle cannot move easily .
R (Reverse): Use this gear to back up. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty . Shift to R (Reverse) only after the vehicle is stopped.
Driver Shift Control (DSC) T o use this feature, do the following: 1. Move the shift lever from D (Drive) rearward to M (Manual). While driving in manual mode, the transmission will remain in the driver selected gear . When coming to a stop in the manual position, the vehicle will automatically shift into 1 (First) gear.
Second or Third Gear Start Feature When accelerating the vehicle from a stop in snowy and icy conditions, you may want to shift the gear select tap switch into Second or Third gear . A higher gear allows you to gain more traction on slippery surfaces.
{ W ARNING: It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly .
N (Neutral): In this position, the engine does not connect with the wheels. T o restart the engine when the vehicle is already moving, use N (Neutral) only . Also, use N (Neutral) when the vehicle is being towed. { W ARNING: Shifting into a drive gear while the engine is running at high speed is dangerous.
Parking Brake T o set the parking brake, push down the parking brake pedal with your left foot. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 4 ‑ 30 . T o release the parking brake, hold the regular brake pedal down with your right foot.
Shifting Into Park { W ARNING: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly . Y ou or others could be injured.
T orque Lock T orque lock is when the weight of the vehicle puts too much force on the parking pawl in the transmission. This happens when parking on a hill and shifting the transmission into P (Park) is not done properly and then it is difficult to shift out of P (Park).
Engine Exhaust { W ARNING: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: . The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airflow or tail pipes).
Running the V ehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know . { W ARNING: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view of behind your vehicle. Adjust the mirror to avoid glare from the headlamps behind. Push the tab forward for daytime use and pull it for nighttime use.
Compass Calibration If after a few seconds the display does not show a compass direction, (N for North for example), there may be a strong magnetic field interfering with the compass. Interference can be caused by a magnetic antenna mount, note pad holder , or similar object.
Outside Power Mirrors Controls for the outside power mirrors are located on the driver door . T o adjust the mirrors: 1. Move the selector switch located below the four-way control pad to the left or right to choose either the driver side or passenger side mirror .
Universal Home Remote System Operation (With Three Round LED) This vehicle may have the Universal Home Remote System. If there are three round Light Emitting Diode (LED) indicator lights above the Universal Home Remote buttons, follow the instructions below .
Programming Universal Home Remote — Rolling Code For questions or help programming the Universal Home Remote System, call 1-866-572-2728 or go to learcar2u.com. Most garage door openers sold after 1996 are Rolling Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting.
3. Immediately return to the vehicle. Press and hold the Universal Home Remote button that will be used to control the garage door until the garage door moves. The indicator light, above the selected button, should slowly blink. This button may need to be held for up to 20 seconds.
T o program up to three devices: 1. T o verify that the garage door opener is a Fixed Code unit, remove the battery cover on the hand held transmitter supplied by the manufacturer of the garage door opener motor . If there are a row of dip switches similar to the graphic above, the garage door opener is a Fixed Code unit.
Example of Eight Dip Switches with Three Positions The panel of switches might not appear exactly as they do in the examples above, but they should be similar . The switch positions on the hand-held transmitter could be labeled, as follows: . A switch in the up position could be labeled as “ Up, ” “ +, ” or “ On.
4. The indicator lights will blink slowly . Enter each switch setting from Step 2 into your vehicle's Universal Home Remote. Y ou will have two and one-half minutes to complete Step 4. Now press one button on the Universal Home Remote for each switch setting as follows: .
Using Universal Home Remote Press and hold the appropriate button for at least half of a second. The indicator light will come on while the signal is being transmitted. Reprogramming Universal Home Remote Buttons Any of the three buttons can be reprogrammed by repeating the instructions.
Instrument Panel Storage An instrument panel storage area, with a removable liner , is located above the radio. Slide the latch toward the back of the vehicle to open the storage area. Front Storage Area A storage area is located in front of the shift lever .
Sunroof On vehicles with a sunroof, the switch is located on the headliner between the map lamps. The sunroof only operates when the ignition is in ON/RUN, ACC/ACCESSORY , or if Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 3 ‑ 22 .
2 NOTES 3-48.
Section 4 Instrument Panel Instrument Panel Overview ........ ........... ..... 4-3 Hazard W arning Flashers . . . . . . . . . . . . . . . . . . . . . . . 4-3 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 4 Instrument Panel T ire Pressure Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34 Malfunction Indicator Lamp . . . . . . . . . . . . . . . . . . . . 4-34 Oil Pressure Light . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel Overview Hazard W arning Flashers | (Hazard W arning Flasher): Press this button located on the instrument panel, to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press | again to turn the flashers off.
T urn Signal/Multifunction Lever The lever on the left side of the steering column operates the following: G : T urn and Lane-Change Signals 5 3 : Headlamp High/Low-Beam Changer O : Exterior Lamp Control Flash-to-Pass. Information for these features is on the pages following.
Headlamp High/Low-Beam Changer T o change the headlamps from low beam to high beam, push the turn signal/multifunction lever away from you. This instrument panel cluster light 3 comes on if the high beam lamps are turned on while the ignition is in ON/RUN.
6 (Low Speed): Slow wipes. 1 (High Speed): Fast wipes. 8 (Mist): Single wipe, move the lever down, then release it. Several wipes, hold the lever down. Clear ice and snow from the wiper blades before using them. If frozen to the windshield, carefully loosen or thaw them.
Cruise Control Cruise control lets a speed of about 25 mph (40 km/h) or more be maintained without keeping your foot on the accelerator . This can really help on long trips. Cruise control does not work at speeds below 25 mph (40 km/h). { W ARNING: Cruise control can be dangerous where you cannot drive safely at a steady speed.
RES+ (Resume): Press to resume a set speed and to accelerate the speed. SET − (Set): Press to set a speed and to decrease the speed. T o set a speed do the following: 1. Press I to turn cruise control on. The indicator light on the button comes on. 2.
Reducing Speed While Using Cruise Control If the cruise control system is already engaged: . Push and hold the SET − until the desired lower speed is reached, then release it. . T o slow down in very small amounts, briefly push the SET − . Each time this is done, the vehicle goes about 1 mph (1.
Headlamps The band on the lever located on the left side of the steering column, operates the exterior lamps. The exterior lamp control has the following four positions: 2 (Headlamps): T urns on the headlamps, parking lamps, and taillamps. ; (Parking Lamps): T urns on the parking lamps and taillamps only .
Delayed Headlamps The delayed headlamps feature keeps the headlamps on for 20 seconds after the key is turned to LOCK/OFF , then the headlamps automatically turn off. T o override the 20 second delayed headlamp feature while it is active turn the turn signal/multifunction lever up one position and then back to AUTO.
If vehicle is started in a dark garage, the automatic headlamp system comes on immediately . Once the vehicle leaves the garage, it takes about one minute for the automatic headlamp system to change to DRL if it is light outside. During that delay , the instrument panel cluster may not be as bright as usual.
Dome Lamps The dome lamps come on when any door is opened. They turn off after all the doors are closed. The dome lamps can also be turned on by turning the instrument panel brightness knob, located on the instrument panel to the left of the steering column, clockwise to the farthest position.
A high electrical load occurs when several of the following are on, such as: headlamps, high beams, fog lamps, rear window defogger , climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets.
Accessory Power Outlet(s) Accessory power outlets can be used to connect auxiliary electrical equipment, such as a cellular telephone. There are two accessory power outlets. One accessory power outlet is located inside the storage bin below the climate controls and the other outlet is on the rear of the center storage console.
Power Outlet 1 15 V olt Alternating Current The vehicle may have a power outlet that can be used to plug in electrical equipment that uses a maximum limit of 150 watts. The power outlet is located on the rear of the center console. An indicator light on the outlet turns on to show it is in use.
Climate Controls Climate Control System The heating, cooling and ventilation for the vehicle can be controlled with this system. A. Fan Control B. Recirculation C. T emperature Control D. Outside Air E. Air Delivery Mode Control F . Air Conditioning G.
- (Defog): This mode clears the windows of fog or moisture. Air is directed to the windshield and floor outlets, with some air directed to the side windows. When this mode is selected, the system automatically turns off recirculation and runs the air-conditioning compressor unless the outside temperature is at or below freezing.
Using these settings together for long periods of time can cause the air inside of the vehicle to become too dry . T o prevent this from happening, after the air in the vehicle has cooled, turn the recirculation mode off. : (Outside Air): Press to turn the outside air mode on.
Remote Start Climate Control Operation For vehicles with the remote start feature, when it is activated the climate control system heats or cools the inside of the vehicle using the modes that were set before the vehicle was turned off. The climate control knobs will remain active during a remote start.
Automatic Operation AUTO (Automatic): Select AUTO on both the fan speed control and the air delivery mode control knobs to activate the automatic system. When automatic operation is active the system controls the inside temperature and air delivery . T o place the system in automatic mode do the following: 1.
Manual Operation 9 (Off): Select this position on the fan knob to turn off the entire climate control system. Outside air still enters the vehicle. The airflow direction and temperature can be adjusted. x / w T emperature Control: Press the arrows to increase or decrease the temperature inside the vehicle.
In AUTO mode the system cools and dehumidifies the air inside the vehicle. Also while in AUTO mode, the system maximizes its performance by using recirculation as necessary . Heating: On cold days when using manual operation of the automatic system, use floor mode to deliver air to the floor outlets.
Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window . < (Rear): Press to turn the rear window defogger on or off. An indicator light comes on to show that the rear window defogger is on. If driving below 50 mph (80 km/h), the rear window defogger turns off about 15 minutes after the button is pressed.
Outlet Adjustment Use the lever located in the center of each outlet by moving it either up and down or side-to-side, to change the direction and amount of airflow in the vehicle. Operation Tips . Clear away any ice, snow , or leaves from the air inlets at the base of the windshield that may block the flow of air into the vehicle.
Instrument Panel Cluster United States Base version shown, Canada Similar 4-26.
Speedometer and Odometer The speedometer shows the vehicle speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far the vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada).
Airbag Readiness Light The system checks the airbag's electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check includes the airbag sensor , the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module.
Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System on page 2 ‑ 66 for important safety information. The instrument panel has a passenger airbag status indicator . United States Canada When the vehicle is started, the passenger airbag status indicator will light ON and OFF , or the symbol for on and off, for several seconds as a system check.
Charging System Light This light comes on briefly when the ignition key is turned to ST ART , but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/ retailer . The light should go out once the engine starts.
The Driver Information Center (DIC) may display a BRAKE FLUID message. See DIC Warnings and Messages on page 4 ‑ 43 for more information. If the light comes on while driving, pull off the road and carefully stop. The brake pedal may be harder to push or the pedal may go closer to the floor.
Electronic Stability Control (ESC)/ T raction Control System (TCS) Indicator/W arning Light The Electronic Stability Control (ESC) system or the T raction Control System (TCS) indicator/ warning light comes on briefly when the engine is started. If it does not, have the vehicle serviced by the dealer/ retailer .
Engine Coolant T emperature W arning Light This light comes on briefly while starting the vehicle. If it does not, have the vehicle serviced by the dealer/ retailer . If the system is working normally the indicator light goes off. Notice: Driving with the engine coolant temperature warning light on could cause the vehicle to overheat.
Tire Pressure Light For vehicles with a tire pressure monitoring system, this light comes on briefly when the engine is started. It provides information about tire pressures and the Tire Pressure Monitoring System. When the Light is On Steady This indicates that one or more of the tires is significantly underinflated.
This light should come on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/ retailer . If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required.
If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. T urn the key off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer/retailer for service as soon as possible.
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration.
If the light comes on and stays on, it means that oil is not flowing through the engine properly . The vehicle could be low on oil and it might have some other system problem. Security Light For information regarding this light and the vehicle's security system, see Content Theft-Deterrent on page 3 ‑ 17 .
Fuel Gauge United States Canada When the ignition is on, the fuel gauge shows much fuel is left in the fuel tank. When the indicator nears empty , a message in the Driver Information Center (DIC) displays. See DIC Warnings and Messages on page 4 ‑ 43 for more information.
Driver Information Center (DIC) Y our vehicle has a Driver Information Center (DIC). The DIC display gives you the status of many of your vehicle's systems. The DIC is also used to display driver personalization menu modes and warning/status messages.
Odometer Press the information button until the outside air temperature and the odometer displays. This mode shows the total distance the vehicle has been driven in either kilometers (km) or miles (mi). T o change the DIC display to English or metric units, see “ UNITS ” under DIC Vehicle Personalization on page 4 ‑ 47 .
MPG (L/100 KM) INST (Instantaneous) Press the information button until MPG (L/100 KM) INST displays. This mode shows the current fuel economy at a particular moment and changes frequently as driving conditions change. This mode shows the instantaneous fuel economy in liters per 100 kilometers (L/100 km) or miles per gallon (mpg).
DIC W arnings and Messages These messages appear if there is a problem detected in one of your vehicle's systems. A message clears when the vehicle's condition is no longer present. T o acknowledge a message and clear it from the display , press and hold any of the DIC buttons.
CRUISE ENGAGED This message displays when the cruise control system is active. See Cruise Control on page 4 ‑ 7 for more information. DOOR AJAR This message displays if one or more of the vehicle's doors are not closed properly . Make sure that the door(s) are closed completely .
ICE POSSIBLE This message displays when the outside air temperature is cold enough to create icy road conditions. Adjust your driving accordingly . KEY FOB BA TT (Battery) LOW This message displays if the Remote Keyless Entry (RKE) transmitter battery is low .
SERVICE ESC (ELECTRONIC ST ABILITY CONTROL) If your vehicle has Electronic Stability Control (ESC), this message displays and a chime sounds if there has been a problem detected with ESC. The ESC/TCS light also appears on the instrument panel cluster .
TIRE LOW ADD AIR On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires is low on air . The low tire pressure warning light also comes on. See Tire Pressure Light on page 4 ‑ 34 .
T o change feature settings, use the following procedure: Entering Personalization Menu 1. T urn the ignition on while the vehicle is stopped. T o avoid excessive drain on the battery , it is recommended that the headlamps are turned off. 2. Press and hold the information and reset buttons at the same time for one second, then release to enter the personalization menu.
REMOTE ST ART If your vehicle has remote start, this feature allows remote start to be turned off or on. Remote start allows you to start the engine from outside of the vehicle using your Remote Keyless Entry (RKE) transmitter . When REMOTE ST ART appears on the display , press and hold the reset button for at least one second to scroll through the available settings: OFF: The remote start feature will be disabled.
LIGHT FLASH This feature, which allows the vehicle's exterior hazard/ turn signal lighting to flash every time the lock, unlock, or trunk release buttons on the Remote Keyless Entry (RKE) transmitter are pressed, can be enabled or disabled. When LIGHT FLASH appears on the display , press and hold the reset button for at least one second to scroll through the available settings: OFF: The exterior hazard/turn signal lighting will not flash when the lock, unlock, or trunk release buttons on the RKE transmitter are pressed.
AUTO UNLK (Unlock) This feature, which allows the vehicle to automatically unlock certain doors, can be enabled or disabled. When AUTO UNLK appears on the display , press and hold the reset button for at least one second to scroll through the available settings: ALL (default): All of the doors will automatically unlock.
LANGUAGE This feature allows you to select the language in which the DIC will display . When LANGUAGE appears on the display , press and hold the reset button for at least one second to scroll through the available settings: ENGLISH (default): All messages will appear in English.
Notice: Contact your dealer/retailer before adding any equipment. Adding audio or communication equipment could interfere with the operation of the vehicle's engine, radio, or other systems, and could damage them. Follow federal rules covering mobile radio and telephone equipment.
With Date Display Radio with CD (MP3) and USB Port, and Radio with Single CD (MP3) Player T o set the time and date: 1. T urn the ignition key to ACC/ACCESSORY or ON/RUN. Press O to turn the radio on. 2. Press H and the HR, MIN, MM, DD, YYYY (hour , minute, month, day , and year) displays.
Radio(s) Radio with CD (Base) Radio with CD (MP3) and USB Port shown, Radio with CD (MP3) similar The vehicle has one of these radios as its audio system.
Radio Data System (RDS) The radio may have RDS. The RDS feature is available for use only on FM stations that broadcast RDS information. This system relies upon receiving specific information from these stations and only works when the information is available.
. T o scan preset stations in the selected band, press and hold © SEEK for four seconds until a double beep sounds. The radio goes to a stored preset, plays for a few seconds, then goes to the next stored preset. Press © SEEK again to stop scanning preset stations.
F A V (Favorites): A maximum of 36 stations can be stored as favorites using the six softkeys located below the radio station frequency tabs and by using the radio favorites page button (F A V button). Press F A V to go through up to six pages of favorites, each having six favorite stations available per page.
Storing a Radio Station as a Preset Radios that have numbered pushbuttons store radio stations as presets. If the radio does not have XM, up to 18 stations (six FM1, six FM2, and six AM), can be programmed on the six numbered buttons. T o store preset stations: 1.
EQ (Equalization): Press this button to select preset equalization settings. T o return to the manual mode, press EQ until Manual displays or start to manually adjust the bass, midrange, or treble by pressing f . Adjusting the Speakers (Balance/Fade) Depending on which radio the vehicle has, the Balance/ Fade can be adjusted using f or ` .
Finding a Category (CA T) Station (XM Satellite Radio Service Only) CA T (Category): The radio may have the CA T button feature. T o select and find a desired category: 1. Press BAND until the XM frequency displays. 2. Press CA T to display the category tabs on the radio display .
XM Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound.
RDM (Random): T racks can be listened to in random, rather than sequential order . T o use random: 1. Press the softkey below RDM tab until Random Current Disc displays. 2. Press the softkey again to turn off random play . BAND: Press to listen to the radio while a CD is playing.
Care of CDs Store CD(s) in their original cases or other protective cases and away from direct sunlight and dust. The CD player scans the bottom of the disc. If the bottom of a CD is damaged it may not play properly or at all. Do not touch the bottom of a CD while handling it.
CD/AUX (CD/Auxiliary): Press to play a CD while a portable audio device is connected to the auxiliary input. Press again and the system begins playing audio from the connected portable audio player . If a portable audio player is not connected, No Aux Input Device may display .
CD ‐ R or CD ‐ RW Supported File and Folder Structure The radio supports: . Up to 50 folders. . Up to 8 folders in depth. . Up to 50 playlists. . Up to 255 files. . Playlists with an .m3u or .wpl extension. . Files with an .mp3 or .cda file extension.
File System and Naming The song name that displays is the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio displays the file name without the extension (such as .mp3) as the track name. T rack names longer than 32 characters or four pages are shortened.
RDM (Random): MP3 files can be listened to on a CD in random, rather than sequential order . T o use random: 1. Press the softkey under the RDM tab until Random Current Disc displays to play songs from the current CD in random order . 2. Press the same softkey again to turn off random play .
Connecting a USB Storage Device or iPod ® The USB Port can be used to control an iPod or a USB storage device. T o connect a USB storage device, connect the device to the USB port located on the front of the radio. T o connect an iPod, connect one end of the USB cable that came with the iPod to the iPod ’ s dock connector and connect the other end to the USB port located on the front of the radio.
Using Softkeys to Control a USB Storage Device or iPod The five softkeys below the radio display are used to control the functions listed below . T o use the softkeys: 1. Press the first or fifth softkey below the radio display to display the functions listed below , or press the softkey below the function if it is currently displayed.
h (Music Navigator): Press the softkey below h to view and select a file on an iPod, using the iPod's menu system. Files are sorted by: . Playlists . Artists . Albums . Genres . Songs . Composers T o select files: 1. Press the softkey below h . 2.
Shuffle Functionality T o use Shuffle: Press the softkey below > , 2 , < or = to select between Shuffle Off, Shuffle All Songs/Shuffle Songs, Shuffle Album, or Shuffle Folder . > (Shuffle Off): Press the softkey below 2 to turn shuffle off. This is the default mode when a USB storage device or iPod is first connected.
No Artist Info: No artist information is available at this time on this channel. The system is working properly . No Title Info: No song title information is available at this time on this channel. The system is working properly . No CA T Info: No category information is available at this time on this channel.
V oice Recognition The Bluetooth system uses voice recognition to interpret voice commands to dial phone numbers and name tags. Noise: Keep interior noise levels to a minimum. The system may not recognize voice commands if there is too much background noise.
Pairing Information: . Up to five cell phones can be paired to the in ‐ vehicle Bluetooth system. . The pairing process is disabled when the vehicle is moving. . The in ‐ vehicle Bluetooth system automatically links with the first available paired cell phone in the order the phone was paired.
Deleting a Paired Phone 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Bluetooth ” . The system responds with “ Bluetooth ready ” followed by a tone. 3. Say “ Delete ” . The system asks which phone to delete followed by a tone.
. If the system is unsure it recognizes the phone number , it responds with “ Store ” and repeats the number followed by “ Please say yes or no ” . If the number is correct, say “ Y es ” . If the number is not correct, say “ No ” . The system will ask for the number to be re ‐ entered.
Using the Directory Command The directory command lists all of the name tags stored by the system. T o use the directory command: 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Directory ” .
Making a Call Calls can be made using the following commands: . Dial . Digit Dial . Call . Re ‐ dial Using the Dial Command 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Dial ” . The system responds with “ Dial using <phone name>.
Using the Call Command 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Call ” . The system responds with “ Call using <phone name>. Please say the name tag ” followed by a tone. 3.
. T o ignore the incoming call, continue with the original call with no action. . Press c x to disconnect the current call and switch to the call on hold. Three ‐ W ay Calling Three ‐ W ay Calling must be supported on the Bluetooth phone and enabled by the wireless service carrier to work.
T o T ransfer Audio to the In-V ehicle Bluetooth System The cellular phone must be paired and connected with the Bluetooth system before a call can be transferred. The connection process can take up to two minutes after the key is turned to the ON/RUN or ACC/ ACCESSORY position.
Sending a Stored Name T ag During a Call 1. Press b g . The system responds with “ Ready ” followed by a tone. 2. Say “ Send name tag. ” The system responds with “ Say a name tag to send tones ” followed by a tone. 3. Say the name tag to send.
Audio Steering Wheel Controls V ehicles with audio steering wheel controls could differ depending on the vehicle's options. Some audio controls can be adjusted at the steering wheel. e + / e − (V olume): Press to increase or to decrease the radio volume.
c (End): Press to reject an incoming call, or end a current call. b g (Mute / V oice Recognition): Press to silence the vehicle speakers only . Press again to turn the sound on. For vehicles with Bluetooth ® or OnStar ® systems press and hold b g for longer than two seconds to interact with those systems.
Backglass Antenna The AM-FM antenna is integrated with the rear window defogger , located in the rear window . Make sure that the inside surface of the rear window is not scratched and that the lines on the glass are not damaged. If the inside surface is damaged, it could interfere with radio reception.
Section 5 Driving Y our V ehicle Y our Driving, the Road, and the V ehicle . . . . . . . . . . 5-2 Defensive Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 D r u n k D r i v i n g ................................. .. 5 - 2 Control of a V ehicle .
Y our Driving, the Road, and the V ehicle Defensive Driving Defensive driving means “ always expect the unexpected. ” The first step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Everyone on page 2 ‑ 1 1 .
For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological, and developmental reasons for these laws. The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive.
allowing realistic following distances eliminates a lot of unnecessary braking. That means better braking and longer brake life. If the engine ever stops while the vehicle is being driven, brake normally but do not pump the brakes. If the brakes are pumped, the pedal could get harder to push down.
Using ABS Do not pump the brakes. Just hold the brake pedal down firmly and let antilock work. The antilock pump or motor might be heard operating and the brake pedal might be felt to pulsate , but this is normal. Braking in Emergencies ABS allows the driver to steer and brake at the same time.
If the vehicle is in cruise control when the system begins to assist the driver maintain directional control of the vehicle, the ESC/TCS light will flash and the cruise control will automatically disengage. The cruise control system may be re-engaged when road conditions allow .
T raction Control System (TCS) The vehicle may have a T raction Control System (TCS) that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that the front wheels are spinning too much or are beginning to lose traction.
T o turn the system off or on, press and release this button located on the center console. The DIC will display the appropriate message as described previously when the button is pressed. T raction Control Operation T raction control limits wheel spin by reducing engine power to the wheels (engine speed management) and by applying brakes to each individual wheel (brake-traction control) as necessary .
Steering Electric Power Steering If the vehicle has the electric power steering system and the engine stalls while driving, the power steering assist system will continue to operate until you are able to stop the vehicle. If power steering assist is lost because the electric power steering system is not functioning, the vehicle can be steered but it will take more effort.
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Off-Road Recovery The vehicle's right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy . Ease off the accelerator and then, if there is nothing in the way , steer so that the vehicle straddles the edge of the pavement.
Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle's three control systems.
. When tired, pull off the road. . Do not wear sunglasses. . Avoid staring directly into approaching headlamps. . Keep the windshield and all glass on your vehicle clean — inside and out. . Keep your eyes moving, especially during turns or curves. No one can see as well at night as in the daytime.
Other Rainy Weather T ips Besides slowing down, other wet weather driving tips include: . Allow extra following distance. . Pass with caution. . Keep windshield wiping equipment in good shape. . Keep the windshield washer fluid reservoir filled. . Have good tires with proper tread depth.
{ W ARNING: If you do not shift down, the brakes could get so hot that they would not work well. Y ou would then have poor braking or even none going down a hill. Y ou could crash. Shift down to let the engine assist the brakes on a steep downhill slope.
Allow greater following distance on any slippery road and watch for slippery spots. Icy patches can occur on otherwise clear roads in shaded areas. The surface of a curve or an overpass can remain icy when the surrounding roads are clear . Avoid sudden steering maneuvers and braking while on ice.
W ARNING: (Continued) Y ou cannot see it or smell it, so you might not know it is in your vehicle. Clear away snow from around the base of your vehicle, especially any that is blocking the exhaust. Run the engine for short periods only as needed to keep warm, but be careful.
Rocking Y our V ehicle to Get It Out T urn the steering wheel left and right to clear the area around the front wheels. T urn off any traction or stability system. Shift back and forth between R (Reverse) and a forward gear , spinning the wheels as little as possible.
Tire and Loading Information Label Label Example A vehicle specific Tire and Loading Information label is attached to the vehicle's center pillar (B-pillar). With the driver door open, you will find the label attached below the door lock post (striker).
Steps for Determining Correct Load Limit 1. Locate the statement “ The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs ” on your vehicle's placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Example 1 Item Description T otal A Maximum V ehicle Capacity Weight for Example 1 = 453 kg (1,000 lbs) B Subtract Occupant Weight @ 68 kg (150 lbs) × 2 = 136 kg (300 lbs) C Available Occupant and Ca.
Example 3 Item Description T otal A Maximum V ehicle Capacity Weight for Example 3 = 453 kg (1,000 lbs) B Subtract Occupant Weight @ 91 kg (200 lbs) × 5 = 453 kg (1,000 lbs) C Available Cargo Weight = 0 kg (0 lbs) Refer to the vehicle's T ire and Loading Information label for specific information about your vehicle's maximum vehicle capacity weight and seating positions.
Never exceed the GVWR for the vehicle or the Gross Axle Weight Rating (GA WR) for either the front or rear axle. { W ARNING: Do not load the vehicle any heavier than the Gross V ehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GA WR).
T owing T owing Y our V ehicle T o avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer/ retailer or a professional towing service if the disabled vehicle must be towed. See Roadside Assistance Program on page 8 ‑ 7 .
Dinghy T owing When dinghy towing, the vehicle should be run at the beginning of each day and at each RV fuel stop for about five minutes. This will ensure proper lubrication of transmission components. T o dinghy tow the vehicle from the front with all four wheels on the ground: 1.
Notice: T owing the vehicle from the rear could damage it. Also, repairs would not be covered by the vehicle warranty . Never have the vehicle towed from the rear . Dolly T owing T ow the vehicle with the two rear wheels on the ground and the front wheels on a dolly: T o tow the vehicle with two wheels on the ground and a dolly: 1.
5. Remove the key from the ignition. 6. Secure the vehicle to the dolly . 7. Release the parking brake. Notice: T owing the vehicle from the rear could damage it. Also, repairs would not be covered by the vehicle warranty . Never have the vehicle towed from the rear .
T railering is different than just driving the vehicle by itself. T railering means changes in handling, acceleration, braking, durability and fuel economy . Successful, safe trailering takes correct equipment, and it has to be used properly . The following information has many time-tested, important trailering tips and safety rules.
Weight of the T railer How heavy can a trailer safely be? It should never weigh more than 1,000 lbs (454 kg). But even that can be too heavy . It depends on how the rig is used. For example, speed, altitude, road grades, outside temperature and how much the vehicle is used to pull a trailer are all important.
T otal Weight on the V ehicle's Tires Be sure the vehicle's tires are inflated to the upper limit for cold tires. These numbers can be found on the Certification/T ire label. See Loading the Vehicle on page 5 ‑ 18 . Make sure not to go over the GVW limit for the vehicle, including the weight of the trailer tongue.
Driving with a T railer T owing a trailer requires a certain amount of experience. Get to know the rig before setting out for the open road. Get acquainted with the feel of handling and braking with the added weight of the trailer . And always keep in mind that the vehicle you are driving is now longer and not as responsive as the vehicle is by itself.
T urn Signals When T owing a T railer The arrows on the instrument panel flash whenever signaling a turn or lane change. Properly hooked up, the trailer lamps also flash, telling other drivers the vehicle is turning, changing lanes or stopping. When towing a trailer , the arrows on the instrument panel flash for turns even if the bulbs on the trailer are burned out.
Leaving After Parking on a Hill 1. Apply and hold the brake pedal while you: . start the engine, . shift into a gear , and . release the parking brake. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks. 4. Stop and have someone pick up and store the chocks.
2 NOTES 5-34.
Section 6 Service and Appearance Care Service ......... ........................... ......... 6-3 Accessories and Modifications . . . . . . . . . . . . . . . . . . 6-3 California Proposition 65 Warning . . . . . . . . . . . . . . . 6-4 California Perchlorate Materials R e q u i r e m e n t s .
Section 6 Service and Appearance Care Buying New T ires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-66 Different Size Tires and Wheels . . . . . . . . . . . . . . . 6-68 Uniform Tire Quality Grading . . . . . . . . . . . . . . . . . .
Service For service and parts needs, visit your dealer/retailer . Y ou will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modifications When non ‐ dealer/non ‐ retailer accessories are added to the vehicle, they can affect vehicle performance and safety , including such things as airbags, braking, stability , ride and handling, emissions systems, aerodynamics, durability , and electronic systems like antilock brakes, traction control, and stability control.
California Proposition 65 W arning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.
Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 7 ‑ 15 . Adding Equipment to the Outside of the V ehicle Things added to the outside of the vehicle can affect the airflow around it.
If the vehicle has the 2.4L L4 engine (VIN Code 0) or the 3.5L V6 engine (VIN Code K), you can use either unleaded gasoline or ethanol fuel containing up to 85% ethanol (E85). See Fuel E85 (85% Ethanol) on page 6 ‑ 8 . In all other engines, use only the unleaded gasoline described under Gasoline Octane on page 6 ‑ 6 .
diagnosis. If it is determined that the condition is caused by the type of fuel used, repairs might not be covered by the vehicle warranty . Additives T o provide cleaner air , all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly .
Fuel E85 (85% Ethanol) The 8th digit of the V ehicle Identification Number (VIN) shows the code letter or number that identifies the vehicle's engine. The VIN is at the top left of the instrument panel. See Vehicle Identification Number (VIN) on page 6 ‑ 103 .
If you do switch fuels, it is recommended that you add as much fuel as possible — do not add less than 1 1 L (three gallons) when refueling. Y ou should drive the vehicle immediately after refueling for at least 1 1 km (seven miles) to allow the vehicle to adapt to the change in ethanol concentration.
Filling the T ank { W ARNING: Fuel vapor burns violently and a fuel fire can cause bad injuries. T o help avoid injuries to you and others, read and follow all the instructions on the fuel pump island. Turn off the engine when refueling. Do not smoke near fuel or when refueling the vehicle.
{ W ARNING: Fuel can spray out on you if you open the fuel cap too quickly . If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather . Open the fuel cap slowly and wait for any hiss noise to stop.
Filling a Portable Fuel Container { W ARNING: Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor . Y ou can be badly burned and the vehicle damaged if this occurs.
Hood Release T o open the hood, do the following: 1. Pull the hood release handle with this symbol on it. It is located inside the vehicle to the left of the steering column. 2. Then go to the front of the vehicle and push the secondary hood release handle toward the driver side of the vehicle.
Engine Compartment Overview When you open the hood on the 2.4L L4 engine, this is what you see: 6-14.
A. See Engine Air Cleaner/Filter on page 6 ‑ 24 . B. Engine Cooling Fan. See Cooling System on page 6 ‑ 26 . C. Engine Oil Fill Cap. See “ When to Add Engine Oil ” under Engine Oil on page 6 ‑ 19 . D. Engine Oil Dipstick (Out of View). See “ Checking Engine Oil ” under Engine Oil on page 6 ‑ 19 .
When you open the hood on the 3.5L V6 engine, this is what you see: 6-16.
A. See Engine Air Cleaner/Filter on page 6 ‑ 24 . B. Power Steering Fluid Reservoir . See Power Steering Fluid on page 6 ‑ 33 . C. Engine Cooling Fan. See Cooling System on page 6 ‑ 26 . D. Engine Oil Fill Cap. See “ When to Add Engine Oil ” under Engine Oil on page 6 ‑ 19 .
When you open the hood on the 3.6L V6 engine, this is what you see: 6-18.
A. See Engine Air Cleaner/Filter on page 6 ‑ 24 . B. Power Steering Fluid Reservoir . See Power Steering Fluid on page 6 ‑ 33 . C. Engine Oil Fill Cap. See “ When to Add Engine Oil ” under Engine Oil on page 6 ‑ 19 . D. Engine Oil Dipstick. See “ Checking Engine Oil ” under Engine Oil on page 6 ‑ 19 .
When to Add Engine Oil L4 Engine V6 Engine If the oil is below the MIN mark for the L4 engine or below the cross ‐ hatched area at the tip of the dipstick for the V6 engine, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use.
What Kind of Engine Oil to Use Look for three things: . GM6094M Use only an oil that meets GM Standard GM6094M. . SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity , or thickness. Do not use other viscosity oils such as SAE 20W-50.
Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty .
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and filter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where the oil is changed prior to a CHANGE OIL SOON message being turned on, reset the system.
Engine Air Cleaner/Filter See Engine Compartment Overview on page 6 ‑ 14 for the location of the engine air cleaner/filter . When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/filter at the Maintenance II intervals and replace it at the first oil change after each 50,000 mile (80 000 km) interval.
3. Inspect or replace the engine air cleaner/filter . 4. Align the filter correctly using the alignment tab. 5. Install the cover by guiding the tabs on the rim of the top cover into the bottom hinges and turn the cover down to close it. 6. The spring clips will engage easily , if the cover is properly seated.
Automatic T ransmission Fluid It is not necessary to check the transmission fluid level. A transmission fluid leak is the only reason for fluid loss. If a leak occurs, take your vehicle to the dealer/retailer and have it repaired as soon as possible. Change the fluid and filter at the intervals listed in Scheduled Maintenance on page 7 ‑ 3 , and be sure to use the transmission fluid listed in Recommended Fluids and Lubricants on page 7 ‑ 1 1 .
{ W ARNING: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury . Keep hands, clothing, and tools away from any underhood electric fan. { W ARNING: Heater and radiator hoses, and other engine parts, can be very hot.
What to Use { W ARNING: Adding only plain water to the cooling system can be dangerous. Plain water , or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle's coolant warning system is set for the proper coolant mixture.
Checking Coolant The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant recovery tank. If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down.
How to Add Coolant to the Radiator { W ARNING: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury . Keep hands, clothing, and tools away from any underhood electric fan. { W ARNING: Steam and scalding liquids from a hot cooling system can blow out and burn you badly .
3. Fill the coolant surge tank with the proper mixture, to the FULL COLD mark. Wait about five minutes, then check to see if the level is below the mark. If the level is below the FULL COLD mark, add additional coolant to bring the level up to the mark.
If Steam Is Coming From The Engine Compartment { W ARNING: Steam from an overheated engine can burn you badly , even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. T urn it off and get everyone away from the vehicle until it cools down.
If the temperature overheat gauge is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slow for about 10 minutes. Keep a safe vehicle distance from the car in front of you.
When to Check Power Steering Fluid Power steering fluid is used in all vehicles with V6 engines. V ehicles with the 4-cylinder engine have electric power steering and do not use power steering fluid. It is not necessary to regularly check power steering fluid unless a leak is suspected in the system, or an unusual noise is heard.
Windshield W asher Fluid What to Use When you need windshield washer fluid, be sure to read the manufacturer's instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing.
Brakes Brake Fluid The brake master cylinder reservoir is filled with DOT 3 brake fluid. See Engine Compartment Overview on page 6 ‑ 14 for the location of the reservoir . There are only two reasons why the brake fluid level in the reservoir might go down: .
What to Add Use only new DOT 3 brake fluid from a sealed container . See Recommended Fluids and Lubricants on page 7 ‑ 1 1 . Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir .
Brake Wear This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly .
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. The vehicle was designed and tested with top-quality brake parts. When parts of the braking system are replaced — for example, when the brake linings wear down and new ones are installed — be sure to get new approved replacement parts.
V ehicle Storage { W ARNING: Batteries have acid that can burn you and gas that can explode. Y ou can be badly hurt if you are not careful. See Jump Starting on page 6 ‑ 40 for tips on working around a battery without getting hurt. Infrequent Usage: Remove the black, negative ( − ) cable from the battery to keep the battery from running down.
Notice: Ignoring these steps could result in costly damage to the vehicle that would not be covered by the warranty . T rying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system.
{ W ARNING: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water . Y ou do not need to add water to the battery installed in your new vehicle.
6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery . Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery . Use a remote positive (+) terminal if the vehicle has one.
Notice: If the jumper cables are connected or removed in the wrong order , electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty . Always connect and remove the jumper cables in the correct order , making sure that the cables do not touch each other or other metal.
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 6 ‑ 47 . For any bulb changing procedure not listed in this section, contact your dealer/retailer . Halogen Bulbs { W ARNING: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb.
3. Remove the three wing nuts, which hold the taillamp assembly , from inside the vehicle. 4. Remove the taillamp assembly . 5. Remove the wiring harness from the taillamp assembly by lifting the release tab. 6. T urn the bulb socket counterclockwise to remove it.
License Plate Lamp T o replace the license plate lamp bulb: 1. Remove the license plate assembly by turning the two screws counterclockwise. 2. T urn and pull the license plate lamp forward through the fascia opening. 3. T urn the bulb socket counterclockwise and pull the bulb straight out of the socket.
Windshield Wiper Blade Replacement Inspect the windshield wiper blades for wear or cracking. See Scheduled Maintenance on page 7 ‑ 3 . T o remove the wiper blade: 1. Pull the windshield wiper arm connector away from the windshield. 2. Push the release button.
W ARNING: (Continued) . Underinflated tires pose the same danger as overloaded tires. The resulting accident could cause serious injury . Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when your tires are cold.
Winter Tires If you expect to drive on snow or ice covered roads often, you may want to get winter tires for your vehicle. All season tires provide good overall performance on most surfaces but they may not offer the traction you would like or the same level of performance as winter tires on snow or ice covered roads.
(A) Tire Size : The tire size is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type, and service description. See the “ T ire Size ” illustration later in this section for more detail.
Compact Spare Tire Example (A) T emporary Use Only : The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone flat.
(G) TPC Spec (Tire Performanc e Criteria Specification) : Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines.
Tire T erminology and Definitions Air Pressure : The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight : This means the combined weight of optional accessories.
GVWR : Gross V ehicle Weight Rating. See Loading the V ehicle on page 5 ‑ 18 . GA WR FRT : Gross Axle Weight Rating for the front axle. See Loading the Vehicle on page 5 ‑ 18 . GA WR RR : Gross Axle Weight Rating for the rear axle. See Loading the Vehicle on page 5 ‑ 18 .
Radial Ply Tire : A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim : A metal support for a tire and upon which the tire beads are seated. Sidewall : The portion of a tire between the tread and the bead.
Inflation - Tire Pressure T ires need the correct amount of air pressure to operate effectively . Notice: Do not let anyone tell you that under ‐ inflation or over ‐ inflation is all right. It is not. If your tires do not have enough air (under ‐ inflation), you can get the following: .
How to Check Use a good quality pocket-type gauge to check tire pressure. Y ou cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are under ‐ inflated. Check the tire's inflation pressure when the tires are cold.
Tire Pressure Monitor System The T ire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your vehicle's tires and transmit tire pressure readings to a receiver located in the vehicle.
Federal Communications Commission (FCC) and Industry Canada See Radio Frequency Statement on page 8 ‑ 20 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/21 1 of Industry Canada. Tire Pressure Monitor Operation This vehicle may have a T ire Pressure Monitor System (TPMS).
Notice: Using non ‐ approved tire sealants could damage the Tire Pressure Monitor System (TPMS) sensors. TPMS sensor damage caused by using an incorrect tire sealant is not covered by the vehicle warranty . Always use the GM approved tire sealant available through your dealer/retailer .
TPMS Sensor Matching Process Each TPMS sensor has a unique identification code. Any time you replace one or more of the TPMS sensors or rotate the vehicle's tires, the identification codes need to be matched to the new tire/wheel location. The sensors are matched, to the tire/wheel locations, in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear tire using a TPMS diagnostic tool.
7. The passenger side rear turn signal comes on to indicate that corner sensor is ready to be learned. Proceed to the passenger side rear tire and repeat the procedure in Step 5. 8. The driver side rear turn signal comes on to indicate that corner sensor is ready to be learned.
When rotating the vehicle's tires, always use the correct rotation pattern shown here. Do not include the compact spare tire in the tire rotation. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the T ire and Loading Information label.
When It Is Time for New T ires V arious factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions influence when you need new tires. One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.
Buying New Tires GM has developed and matched specific tires for your vehicle. The original equipment tires installed on your vehicle, when it was new , were designed to meet General Motors T ire Performance Criteria Specification (TPC Spec) system rating.
{ W ARNING: If you use bias-ply tires on the vehicle, the wheel rim flanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly , causing a crash. Use only radial-ply tires with the wheels on the vehicle. If you must replace your vehicle's tires with those that do not have a TPC Spec number , make sure they are the same size, load range, speed rating, and construction type (radial and bias ‐ belted tires) as your vehicle's original tires.
Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this may affect the way your vehicle performs, including its braking, ride and handling characteristics, stability , and resistance to rollover .
All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition T o These Grades. T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis.
Used Replacement Wheels { W ARNING: Putting a used wheel on the vehicle is dangerous. Y ou cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.
If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle's tires properly . If air goes out of a tire, it is much more likely to leak out slowly . But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side.
Tire Sealant and Compressor Kit { W ARNING: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death.
Read and follow all of the tire sealant and compressor kit instructions. The kit includes: A. On/Off Button B. Selector Switch (Sealant/Air or Air Only) C. Pressure Relief Button D. Pressure Gauge E. Air Only Hose (Black) F . Sealant/Air Hose (Clear) G.
Using the Tire Sealant and Compressor Kit to T emporarily Seal and Inflate a Punctured Tire Follow the directions closely for correct sealant usage. When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for 5 minutes.
7. Start the vehicle. The vehicle must be running while using the air compressor . 8. T urn the selector switch (B) clockwise to the Sealant + Air position. 9. Press the on/off (A) button to turn the tire sealant and compressor kit on. The compressor will inject sealant and air into the tire.
16. If the flat tire was able to inflate to the recommended inflation pressure, remove the maximum speed label from the sealant canister and place it in a highly visible location. The label is a reminder not to exceed 55 mph (90 km/h) until the damaged tire is repaired or replaced.
Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) T o use the air compressor to inflate a tire with air only and not sealant: Always do a safety check first. See If a Tire Goes Flat on page 6 ‑ 72 . 1. Remove the tire sealant and compressor kit from its storage location.
10. Inflate the tire to the recommended inflation pressure using the pressure gauge (D). The recommended inflation pressure can be found on the T ire and Loading Information label. See Inflation - Tire Pressure on page 6 ‑ 57 . The pressure gauge (D) may read higher than the actual tire pressure while the compressor is on.
Tire Sealant and Compressor Kit Storage The tire sealant and compressor kit is located in the trunk. 1. Open the trunk. See T runk on page 3 ‑ 12 . 2. Lift the cover . 3. T urn the retainer clockwise and remove the tire sealant and compressor kit. T o store the tire sealant and compressor kit, reverse the steps.
When the vehicle has a flat tire (B), use the following example as a guide to assist you in the placement of wheel blocks (A). A. Wheel Block B. Flat T ire The following information explains how to use the jack and change a tire. Removing the Spare Tire and T ools The equipment you will need is in the trunk.
Tire Changing T ools The tools you will be using include the wheel wrench (A) and jack (B). 1. T urn the wing nut counterclockwise to loosen wheel wrench.
3. Extend the handle on the wheel wrench by pressing the button and pulling on the end of the wrench. Y ou must do this before using the wheel wrench. Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See Changing a Flat Tire on page 6 ‑ 80 .
4. Use the wrench to loosen all the wheel nuts. Do not remove them yet. 5. Position the lift head at the jack location nearest the flat tire. Make sure all of the jack lift head is touching the jacking flange under the body . Do not place the jack under a body panel.
{ W ARNING: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. { W ARNING: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall.
8. Remove all of the wheel nuts. 9. Remove the flat tire. { W ARNING: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
{ W ARNING: Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash. 12. Put the wheel nuts back on with the rounded end toward the wheel. T ighten each nut by hand or with the wrench until the wheel is held against the hub.
{ W ARNING: Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts.
Storing a Flat or Spare Tire and T ools Storing a Flat Tire and T ools { W ARNING: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury . In a sudden stop or collision, loose equipment could strike someone.
5. Raise the jack to the height shown and lock the wrench onto the jack. 6. Place the jack over the bolt (A) on the floor , making sure it contacts the bolt. Thread the jack retainer nut until it contacts the jack. 7. With the valve stem up, place the tire on the compartment floor with the rear of the tire under the trim panel.
A. Cover B. Wing Nut C. Extension D. Flat T ire (valve stem up) E. Nut F . Jack G. Bolt The compact spare is for temporary use only . Replace the compact spare tire with a full-size tire as soon as you can.
Storing the Spare Tire and T ools { W ARNING: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury . In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
4. Raise the jack to the height shown and lock the wrench onto the jack. 5. Place the jack in the spare tire well. Make sure the stow bolt goes through the hole in the center of the wrench on the jack, with the base of the jack towards the front of the vehicle.
After installing the compact spare on the vehicle, stop as soon as possible and make sure the spare tire is correctly inflated. The compact spare is made to perform well at speeds up to 65 mph (105 km/h) for distances up to 3,000 miles (5 000 km), so you can finish your trip and have the full-size tire repaired or replaced at your convenience.
Notice: Using abrasive cleaners when cleaning glass surfaces on the vehicle, could scratch the glass and/or cause damage to the rear window defogger . When cleaning the glass on the vehicle, use only a soft cloth and glass cleaner . Many cleaners contain solvents that may become concentrated in the vehicle's breathing space.
Fabric/Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt. A canister vacuum with a beater bar in the nozzle may only be used on floor carpet and carpeted floor mats. For any soil, always try to remove it first with plain water or club soda.
Leather A soft cloth dampened with water can be used to remove dust. If a more thorough cleaning is necessary , a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally . Do not use heat to dry . Never use steam to clean leather .
Care of Safety Belts Keep belts clean and dry . { W ARNING: Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water . Weatherstrips Silicone grease on weatherstrips will make them last longer , seal better , and not stick or squeak.
Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter the vehicle. Avoid using high pressure washes closer than 12 inches (30 cm) to the surface of the vehicle.
Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep their luster . Washing with water is all that is usually needed. However , chrome polish may be used on chrome or stainless steel trim, if necessary . Use special care with aluminum trim.
The surface of these wheels is similar to the painted surface of the vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because the surface could be damaged. Do not use chrome polish on aluminum wheels.
Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody . If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection.
V ehicle Identification V ehicle Identification Number (VIN) This legal identifier is in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside. The VIN also appears on the V ehicle Certification and Service Parts labels and certificates of title and registration.
Electrical System Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer/retailer first. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle's warranty .
Fuses The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible links. This greatly reduces the chance of damage caused by electrical problems. Look at the silver-colored band inside the fuse.
6-106.
Fuses Usage POWER MIRRORS Power Mirrors EPS Electronic Power Steering RUN/CRANK Cruise Control Switch, Passenger Airbag Status Indicator HV AC BLOWER HIGH Heating V entilation Air Conditioning Blower .
Fuses Usage NOT INST ALLED Not Used NOT INST ALLED Not Used AIRBAG (BA TT) Airbag (Battery) SP ARE FUSE HOLDER Spare Fuse Holder SP ARE FUSE HOLDER Spare Fuse Holder SP ARE FUSE HOLDER Spare Fuse Holder SP ARE FUSE HOLDER Spare Fuse Holder FUSE PULLER Fuse Puller Engine Compartment Fuse Block The vehicle may not be equipped with all the fuses and features listed.
Fuses Usage 1 Air Conditioner Clutch 2 Electronic Throttle Control 3 Not Used Fuses Usage 4 T ransmission Control Module Ignition 1 5 Mass Airflow Sensor (L Y7) 6 Emission 6-109.
Fuses Usage 7 Left Headlamp Low-Beam 8 Horn 9 Right Headlamp Low-Beam 10 Front Fog Lamps 1 1 Left Headlamp High-Beam 12 Right Headlamp High-Beam 13 Engine Control Module BA TT 14 Windshield Wiper 15 A.
Relays Usage 28 Cooling Fan 1 29 Cooling Fan Series/Parallel 30 Cooling Fan 2 31 Starter 32 Run/Crank, Ignition 33 Powertrain 34 Air Conditioning Clutch 35 High Beam 36 Front Fog Lamps 37 Horn 38 Low-Beam Headlamp 39 Windshield Wiper 1 40 Windshield Wiper 2 48 Daytime Running Lamps 49 Stoplamps 53 AIR Solenoid Diodes Usage 27 Wiper Rear Compartment Fuse Block The rear compartment fuse block is located in the trunk of the vehicle.
Fuses Usage 1 Passenger Seat Controls 2 Driver Seat Controls 3 Not Used Fuses Usage 4 Not Used 5 Emission 2, Canister V ent Solenoid 6 Park Lamps, Instrument Panel Dimming 6-1 12.
Fuses Usage 7 Not Used 8 Not Used 9 Not Used 10 Sunroof Controls 1 1 Not Used 12 Not Used 13 Audio Amplifier 14 Heated Seat Controls 15 Not Used 16 Remote Keyless Entry (RKE) System, XM ™ Satellite .
Capacities and Specifications The following approximate capacities are given in metric and English conversions. Please refer to Recommended Fluids and Lubricants on page 7 ‑ 1 1 for more information. Application Capacities Metric English Air Conditioning Refrigerant R134a For the air conditioning system refrigerant charge amount, see the refrigerant caution label located under the hood.
Engine Specifications Engine VIN Code T ransmission Spark Plug Gap 2.4L L4 Engine B Automatic 1.01 mm (0.040 in) 2.4L L4 Engine 0 Automatic 1.01 mm (0.040 in) 3.5L V6 Engine K Automatic 1.01 mm (0.040 in) 3.5L V6 Engine N Automatic 1.01 mm (0.040 in) 3.
2 NOTES 6-1 16.
Section 7 Maintenance Schedule Maintenance Schedule ........................ .... 7-2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Scheduled Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Owner Checks and Services .
Maintenance Schedule Introduction Notice: Maintenance intervals, checks, inspections, recommended fluids, and lubricants are necessary to keep this vehicle in good working condition. Damage caused by failure to follow scheduled maintenance might not be covered by the vehicle warranty .
At your dealer/retailer , you can be certain that you will receive the highest level of service available. Y our dealer/retailer has specially trained service technicians, uses genuine replacement parts, as well as, up to date tools and equipment to ensure fast and accurate diagnostics.
When the Change Oil Soon message displays, certain services, checks, and inspections are required. The services described for Maintenance I should be performed at every engine oil change. The services described for Maintenance II should be performed when: .
Maintenance II . Perform all services described in Maintenance I . . Steering and suspension inspection. Visual inspection for damaged, loose, or missing parts or signs of wear . . Engine cooling system inspection. Visual inspection of hoses, pipes, fittings, and clamps and replacement, if needed.
Additional Required Services At Each Fuel Stop . Engine oil level check. See Engine Oil on page 6 ‑ 19 . . Engine coolant level check. See Engine Coolant on page 6 ‑ 27 . . Windshield washer fluid level check. See Windshield Washer Fluid on page 6 ‑ 35 .
First Engine Oil Change After Every 40 000 km/25,000 Miles . Fuel system inspection for damage or leaks. First Engine Oil Change After Every 80 000 km/50,000 Miles . Engine air cleaner filter replacement. See Engine Air Cleaner/Filter on page 6 ‑ 24 .
Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter . Reset oil life system. • • Engine coolant level check. • • Windshield washer fluid level check. • • T ire inflation pressures check. • • T ire wear inspection.
Owner Checks and Services Starter Switch Check { W ARNING: When you are doing this inspection, the vehicle could move suddenly . If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
Ignition T ransmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position. . The ignition should turn to LOCK/OFF only when the shift lever is in P (Park). . The ignition key should come out only in LOCK/OFF .
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number , or specification can be obtained from your dealer/retailer . Usage Fluid/Lubricant Engine Oil Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol.
Maintenance Replacement Parts Replacement parts identified below by name, part number , or specification can be obtained from your dealer/retailer . Part Part Numbers ACDelco Part Numbers Engine Air Cleaner/Filter 22676970 A1627C Engine Oil Filter 2.4L L4 Engine 12605566 PF457G 3.
Engine Drive Belt Routing 2.4L L4 Engine 3.5L V6 Engine 7-13.
3.6L V6 Engine 7-14.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided.
Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-16.
Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-17.
Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-18.
Section 8 Customer Assistance Information Customer Assistance and Information . . . . . . . . . . . 8-2 Customer Satisfaction Procedure . . . . . . . . . . . . . . . 8-2 Online Owner Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Customer Assistance for T ext T elephone (TTY) U s e r s .
Customer Assistance and Information Customer Satisfaction Procedure Y our satisfaction and goodwill are important to your dealer and to Chevrolet. Normally , any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer's sales or service departments.
STEP THREE — U.S. Owners: Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle. However , if you continue to remain unsatisfied after following the procedure outlined in Steps One and T wo, you can file with the Better Business Bureau (BBB) Auto Line Program to enforce your rights.
STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps 1 and 2, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/ Arbitration Program.
Online Owner Center Online Owner Center (U.S.) — www .gmownercenter .com/chevrolet Information and services customized for your specific vehicle — all in one convenient place. . Digital owner manual, warranty information, and more . Online service and maintenance records .
Customer Assistance for T ext T elephone (TTY) Users T o assist customers who are deaf, hard of hearing, or speech-impaired and who use T ext T elephones (TTYs), Chevrolet has TTY equipment available at its Customer Assistance Center . Any TTY user in the U.
Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V . Customer Assistance Center Paseo de la Reforma # 2740 Col. Lomas de Bezares C.P .
Calling for Assistance When calling Roadside Assistance, have the following information ready: . Y our name, home address, and home telephone number . T elephone number of your location . Location of the vehicle . Model, year , color , and license plate number of the vehicle .
Services Provided . Emergency Fuel Delivery: Delivery of enough fuel for the vehicle to get to the nearest service station. . Lock ‐ Out Service: Service is provided to unlock the vehicle if you are locked out. A remote unlock may be available if you have OnStar ® .
Services Specific to Canadian Purchased V ehicles . Fuel delivery: Reimbursement is approximately $5 Canadian. Diesel fuel delivery may be restricted. Propane and other fuels are not provided through this service. . Lock-Out Service: V ehicle registration is required.
Scheduling Service Appointments When your vehicle requires warranty service, contact your dealer/retailer and request an appointment. By scheduling a service appointment and advising your service consultant of your transportation needs, your dealer/retailer can help minimize your inconvenience.
T ransportation Options W arranty service can generally be completed while you wait. However , if you are unable to wait, GM helps to minimize your inconvenience by providing several transportation options. Depending on the circumstances, your dealer can offer you one of the following: Shuttle Service Shuttle service is the preferred means of offering Courtesy Transportation.
Additional Program Information All program options, such as shuttle service, may not be available at every dealer . Please contact your dealer for specific information about availability . All Courtesy T ransportation arrangements will be administered by appropriate dealer personnel.
Repair Facility We recommend that you choose a collision repair facility that meets your needs before you ever need collision repairs. Y our dealer/retailer may have a collision repair center with GM-trained technicians and state of the art equipment, or be able to recommend a collision repair center that has GM-trained technicians and comparable equipment.
. If you need roadside assistance, call GM Roadside Assistance. See Roadside Assistance Program on page 8 ‑ 7 for more information. . If your vehicle cannot be driven, know where the towing service will be taking it. Get a card from the tow truck operator or write down the driver's name, the service's name, and the phone number.
Managing the V ehicle Damage Repair Process In the event that your vehicle requires damage repairs, GM recommends that you take an active role in its repair . If you have a pre-determined repair facility of choice, take your vehicle there, or have it towed there.
Reporting Safety Defects to the Canadian Government If you live in Canada, and you believe that your vehicle has a safety defect, notify Transport Canada immediately , in addition to notifying General Motors of Canada Limited. Call them at 1-800-333-0510 or write to: T ransport Canada Road Safety Branch 2780 Sheffield Road Ottawa, Ontario K1B 3V9 Reporting Safety Defects to General Motors In addition to notifying NHTSA (or T ransport Canada) in a situation like this, please notify General Motors.
Owner Information Owner publications are written specifically for owners and intended to provide basic operational information about the vehicle. The owner manual includes the Maintenance Schedule for all models. In-Portfolio: Includes a Portfolio, Owner Manual, and W arranty Booklet.
Event Data Recorders This vehicle has an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an airbag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle's systems performed.
OnStar ® If the vehicle has OnStar and you subscribe to the OnStar services, please refer to the OnStar T erms and Conditions for information on data collection and use. Navigation System If your vehicle has a navigation system, use of the system may result in the storage of destinations, addresses, telephone numbers, and other trip information.
A Accessories and Modifications . . . . . . . . . . . . . . . . . . . . . . . 6-3 Accessory Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22 Accessory Power Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 Add-On Electrical Equipment .
Audio System(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-55 Automatic Climate Control System . . . . . . . . . . . . . . . . . 4-20 Automatic Headlamp System . . . . . . . . . . . . . . . . . . . . . . 4-1 1 Automatic Transmission Fluid .
Chemical Paint Spotting . . . . . . . . . . . . . . . . . . . . . . . . . . 6-102 Child Restraints Infants and Y oung Children . . . . . . . . . . . . . . . . . . . . . . . 2-35 Lower Anchors and T ethers for Children . . . . . . . . . . 2-43 Older Children .
D Damage Repair , Collision . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13 Data Recorders, Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19 Daytime Running Lamps (DRL) . . . . . . . . . . . . . . . . . . . . 4-1 1 Defensive Driving .
Electronic Stability Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Electronic Stability Control Indicator Light . . . . . . . . . . 4-32 Engine Air Cleaner/Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-24 Check and Service Engine Soon Lamp .
Fuel (cont.) Filling the T ank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10 Fuels in Foreign Countries . . . . . . . . . . . . . . . . . . . . . . . . . 6-9 Gasoline Octane . . . . . . . . . . . . . . . . . . . . . . . . .
I Ignition Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21 Infants and Y oung Children, Restraints . . . . . . . . . . . . 2-35 Inflation - T ire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-57 Instrument Panel Brightness .
Lights (cont.) Flash-to-Pass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 High/Low Beam Changer . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Highbeam On . . . . . . . . . . . . . . . . . . . . . . . . . . .
O Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27 T rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27 Off-Road Recovery . . . . . . . . . . . . . . .
Power (cont.) Lumbar Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Outlet 1 15 V olt Alternating Current . . . . . . . . . . . . . . . . 4-16 Retained Accessory (RAP) . . . . . . . . . . . . . . . . . . . . . . . 3-22 Seat .
Ride Control Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Electronic Stability (ESC) . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Roadside Assistance Program . . . . . . . . . . . . . . . . . . . . . . . 8-7 Rocking Y our V ehicle to Get it Out .
Shifting Into Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32 Signals, Turn and Lane-Change . . . . . . . . . . . . . . . . . . . . . 4-4 Spare T ire Compact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T ires (cont.) Pressure Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34 Pressure Monitor Operation . . . . . . . . . . . . . . . . . . . . . . 6-60 Pressure Monitor System . . . . . . . . . . . . . . . . . . . . . . .
W W arning Lights, Gauges, and Indicators . . . . . . . . . . . 4-25 W arnings DIC Warnings and Messages . . . . . . . . . . . . . . . . . . . . . 4-43 Hazard Flashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Safety and Symbols .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Chevrolet 2010 Malibu è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Chevrolet 2010 Malibu - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Chevrolet 2010 Malibu imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Chevrolet 2010 Malibu ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Chevrolet 2010 Malibu, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Chevrolet 2010 Malibu.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Chevrolet 2010 Malibu. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Chevrolet 2010 Malibu insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
