Manuale d’uso / di manutenzione del prodotto 7201560 del fabbricante Char-Broil
Vai alla pagina of 16
P/N 42804297 (10-02-07) T ools needed f or assembl y: 2 Adjustable Wrenches 7/16” Open-End W rench Flat Screwdriver 04201101 07201560 Smok er , BBQ and Grill CA UTION Some parts may contain sharp edges.
K ey # Part N umb er D es cr iption Qu antit y A 55 71 0 23 2 SILVE R SMO KE CH AM B E R K IT 1 B 29 00 1 71 2 FIR E B OX TO P 1 C 55 71 0 23 4 FIR E B OX B OTT OM K IT 1 D 55 71 0 23 5 WOO D SH E LF .
Attach leg braces to the outside of one leg assembly using #10-24x1-3/4” screws and #10-24 flange nuts . Make sure slotted (oval) hole is toward bottom of leg . DO NOT FULL Y TIGHTEN screws until Step 6 is complete. 2 1 FIRST , GET A HELPER! This unit is heavy and requires a second person for lifting and moving.
3 Lay the leg assembly on its side with legs braces pointing upward. Insert the wood rack hooks into leg holes and swing rack upward, parallel to leg braces. 4 With the aid of a helper , place leg holes of remaining leg assembly over wood rack hooks and rotate leg assembly until it meets the leg braces.
6 5 Insert a cotter pin into the hole at one end of the axle and bend the ends of the pin back so that it cannot be removed. Slide a wheel onto the axle. Slide the axle through the holes at the ends of the short legs. Slide remaining wheel onto axle and secure with remaining cotter pin.
7 8 Attach Firebox T op Assembly to Firebox Bottom Assembly using eight 1/4-20x3/4” hex-head bolts as shown below . NOTE: Smoker chamber and firebox doors not pictured for clarity . TM TM Diamond Fire Plate Installation - For models without Diamond Fire ignitor accessory , part number 22504850.
9 10 Smokestack Smokestack plate NOTE: Smoker chamber door not pictured for clarity . From inside the smoker chamber , slide the smokestack through the large hole. Align the two holes in the smokestack plate with the holes in the chamber and secure with two 1/4-20x3/4” hex-head bolts outside the chamber and 1/4-20 flange nuts inside.
1 1 12 NOTE: Smoker chamber door not pictured for clarity . Install grate support screws in the four rear holes and two front-center holes in the smoker chamber . Use six #10-24x1” screws and #10 flange nuts . NOTE: Smoker chamber door not pictured for clarity .
Hole plug NOTE: Smoker chamber door not pictured for clarity . First , attach shelf slats to the two outer holes in shelf brackets using two #10-24x1” screws and #10-24 flange nuts per slat. DO NOT FULL Y TIGHTEN SCREWS . Second , fully tighten hex-head bolts on shelf brackets (installed in previous step).
16 15 Hang grease clip from holes on bottom right side of smoker chamber. A 12 oz. soup or vegetable can will fit nicely into clip to collect grease. Grease Clip If logo plate is not already installed, insert logo plate pins into two holes in lower right corner of smoker chamber door .
18 17 NOTE: Smoker chamber door not pictured for clarity . If you wish to grill in the smoker chamber , place two of the three wire fire grates into bottom of smoker chamber . Place two large porcelain cooking grates into chamber , resting them on the grate support screws.
19 Firebox Cooking Grate Installation for Grilling: NOTE: Firebox door not pictured for clarity . Insert small porcelain cooking grate into firebox. Small Porcelain Cooking Grate (1).
WARNING MOST SURF ACES ON THIS UNIT ARE HOT WHEN IN USE. USE EXTREME CAUTION. KEEP OTHERS A W A Y FROM UNIT . AL W A YS WEAR PROTECTIVE CLOTHING TO PREVENT INJUR Y . HARD WARE LIST Hardware is shown actual size. Y ou may have spare hardware after assembly is complete.
Preparing and Using Y our Silver Smoker Before cooking with your Silver Smoker , the following steps should be closely followed to both cure the finish and season the interior steel. Failure to properly follow these steps may damage the finish and/or impart metallic flavors to your first foods.
Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of purchase.
Char-Broil, LLC • Columbus, GA 31904 • Assembly Instructions © 2007 Printed in China.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Char-Broil 7201560 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Char-Broil 7201560 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Char-Broil 7201560 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Char-Broil 7201560 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Char-Broil 7201560, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Char-Broil 7201560.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Char-Broil 7201560. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Char-Broil 7201560 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
