Manuale d’uso / di manutenzione del prodotto DT-X8 del fabbricante Casio
Vai alla pagina of 75
Handheld T erminal User’ s Guide Series Be sure to r ead “Safety Precautions” inside this guide before trying to use your Handheld T erminal. E DT-X8.
Information in this document is subject to change without advance notice. CASIO Computer Co., Ltd. makes no representations or warranties with respect to the contents or use of this manual and speci fi cally disclaims any express or implied warranties of merchantability or fi tness for any particular purpose.
E-1 Contents .......................................................................................................... E-1 Safety Precautions ......................................................................................... E-3 Operating Precautions .
E-2 Performing Bluetooth ® Communication ..................................................... E-36 Resetting the Handheld T erminal ................................................................E-37 Performing a Full Reset (Initialization) .......
E-3 Safety Pr ecautions Congratulations upon your selection of this CASIO product. Be sure to read the following Safety Precautions before trying to use it for the fi rst time.
E-4 W arning Dust and Moisture Though the Handheld T erminal is dust and water splash resistant, its options including the battery pack are not. Keep loose metal objects and containers fi lled with liquid away from your Handheld T erminal and the options.
E-5 Caution Foreign Objects T ake care to ensure that metals or combustible objects are not inserted into the openings of the Handheld T erminal or its options, and not to allow moisture to get inside of them. Location Install the cradle properly on a fl at and stable surface so that it cannot fall down onto fl oor .
E-6 Optional Lithium-ion Battery Pack Danger Never use the Handheld T erminal and its option including the battery pack and battery next to open fl ame, near a stove, or any other area exposed to high heat, or leave them for a long period of time in a vehicle parked in direct sunlight.
E-7 Power Supply / AC Adaptor W arning Do not use the Handheld T erminal at a voltage other than the speci fi ed voltage. Also, do not connect the Handheld T erminal to a multi-plug power strip. Never modify , sharply bend, twist, or pull on the power cord.
E-8 Operating Pr ecautions Y our Handheld T erminal and its options are precision. Improper operation or rough handling can cause problems with data storage and other problems. Note and observe the following precautions to ensure proper operation. Do not leave dead battery pack in the Handheld T erminal for a long period.
E-9 Lithium-ion Battery Pack Each lithium-ion battery pack has its life. The life span heavily depends on how the battery pack is charged or stored which may cause deterioration of the battery pack to shorten the life span if it is handled improperly .
E-10 About the W aterproofi ng/Dustpr oofi ng The DT -X8 Series models are waterproof and dustproof. W aterproo fi ng: Performance complies with the IPX7 level set out in the IEC standards (waterproof for 30 minutes at a depth of 1 meter in still tap water at normal temperature).
E-11 W ar ning Label W ar ning! ■ Never look directly into the laser light. These products scan using laser light. Never look directly into the laser light or shine the laser light into the eyes.
E-12 Important This guide does not include any information about programming and download procedures. See the applicable separate documentation for information about the procedures.
E-13 Checking in the Box Please check the contents of the box before using the Handheld T erminal for the fi rst time. Open the box and make sure that all the items shown here are included.
E-14 DT -X8 Series Handheld T erminal System Confi guration Options USB Cradle HA-K60IO Ethernet Cradle HA-K62IO The illustration shows the USB Cradle (HA-K60IO). Dual Battery Charger HA-F32DCHG USB and Charging Unit HA-K65US For the latest options list, refer to the ON-LINE manual available at http://world.
E-15 Options Power Cord for Eur ope AC-CORD-EU Power Cord for North America AC-CORD-US Power Cord for T aiwan AC-CORD-TW Power Cord for Kor ea AC-CORD-KR Power Cord for Australia AC-CORD-AU AC Adaptor.
E-16 13 12 3 4 5 6 8 7 9 10 15 14 11 12 17 18 20 16 28 19 20 16 22 22 16 16 23 27 24 25 24 25 26 21 Left Front Right To p Bottom Back General Guide.
E-17 1 Speaker Generates audio and buzzer tones. 2 Indicator 1 Orange: Charging Green: Charging complete Red: Battery pack error or the surrounding temperature is out of the charging temperature range. 3 Indicator 2 Flashes blue when operating via Bluetooth or orange when operating via W -LAN.
E-18 15 CLR Key Used to clear one letter to the left of the cursor . 16 Strap Holes Used to attach neck strap and hand belt. 17 microSD Card Slot microSD card slot. 18 R T rigger Key Used to perform bar code reading. 19 L T rigger Key Used to perform bar code reading.
E-19 Loading and Removing the Battery Pack Y our Handheld T erminal uses two types of battery: a battery pack and a memory backup battery . The battery pack is used to power normal operations and to s.
E-20 Loading 1. T urn the terminal over , turn the left and right lock switches for the battery pack cover to the “FREE” position ( ), and then remove the battery pack cover ( ). 2. Load a battery pack (HA-K23XLBA T). T ake care that the battery pack is oriented correctly when you load it.
E-21 Removing 1. Make sure that the Handheld T erminal is turned off. If the power is on, press the power key to turn it off. 2. T urn the terminal over , turn the left and right lock switches for the battery pack cover to the “FREE” position ( ), and then remove the battery pack cover ( ).
E-22 Attaching the Pen Cor d The pen cord can be used to prevent the pen (stylus) from being lost. Since there are two strap holes where the pen cord can be attached on the back of the terminal near the top, use the hole that affords the greatest ease of use.
E-23 Attaching the Hand Strap The hand strap can be used to prevent the Handheld T erminal from fall. Since there are four strap holes where the hand strap can be attached, use the hole that affords the greatest ease of use. Attach the hand strap according to the procedure described below .
E-24 Calibrating T ouch Panel Alignment Whenever the response of the touch panel is poor , or operation being executed does not match with the location you are tapping on the touch panel, please recalibrate the alignment of the touch panel using the following method.
E-25 Setting the Display Brightness Adjusting Display Brightness Y ou can use the following procedures to adjust display brightness to make it easier to read under different lighting conditions. Press the “Fn” key and then press the “5” key or “6” key after con fi rming that “F” is displayed on the screen.
E-26 Using the Laser Scanner (Laser Models) 1. After turning on the power , position the laser scanner close to a bar code and then press the trigger key . 2. The laser emits light and scans the bar code. If scanning is completed normally , Indicator 2 displays a green light.
E-27 Bar Code Scanning Position Position the laser scanner close to the bar code when scanning small bar codes. Position the laser scanner at a distance from the bar code so that the bars enter the light when scanning large bar codes. Margin Margin Good Good Good Bad Bad Bad Bad W ar ning! ■ Never look directly into the laser light.
E-28 Adjusting the Laser Light Emission Width The emission width of the laser light emitted by the Handheld T erminal (model dependant) can be adjusted. Adjust the emission width when it is improper . 1. Navigate to the menus in the following sequence: Start Settings Control Panel The Control Panel appears as shown in the screen.
E-29 4. T ap the [Calibration] button. The display appears as shown at right. 5. Press the trigger key to emit laser light, and align the light with the barcode for adjusting emission width. Align the laser light with the narrow bars on both sides. The message appears as shown at right when adjustment is completed.
E-30 Using the CMOS Imager (Imager Models) 1. T urn on the Handheld T erminal, position its CMOS Imager reader port near the bar code or 2D code, and then press the trigger key . 2. The Handheld T erminal reads the code by emitting laser and red lights.
E-31 Using the Full Range Imager (Full Range Imager Models) 1. T urn on the Handheld T erminal, aim its CMOS Imager reader port toward the bar code or 2D code, and then press the trigger key . The aimer in a round shape is emitted onto barcode. 2. The Handheld T erminal reads the code by emitting laser and red lights.
E-32 Handling the NFC Reader/W riter (DT -X8-11E/11C/21E/21C) NFC is a type of RFID (Radio Frequency Identi fi cation) technology that allows the data in a device to be read simply by holding the device up to an NFC reader .
E-33 Important! Both contactless IC cards and RFID tags The NFC employs a low power radio wave which does not r equire r egulatory station license. Frequency band used by the NFC is 13.56 MHz. Secur e a suf fi cient space between DT -X8 and other reader/writer located in the vicinity .
E-34 Handling micr oSD Cards The Handheld T erminal supports microSD card. Install (or remove) a microSD card according to the procedure described below .
E-35 Removing 1. Open the cover of the microSD card slot and press on the microSD card ( ). The microSD card is pushed out ( ). 2. Pull out the microSD card and close the cover of the microSD card slot. Important! A microSD card must be inserted with the top and bottom properly aligned and in the proper direction.
E-36 Performing Bluetooth ® Communication Bluetooth ® interface can also be used to transfer data between two Handheld T erminals. W ith Bluetooth ® the two Handheld T erminals should be located within about three meters (9 '10 3 ⁄ 8 " ) from each other , as long as there is nothing blocking the path between them.
E-37 Resetting the Handheld T erminal Resetting the terminal is the same as resetting a PC. Performing a reset causes all unsaved RAM data to be lost that are in mid-course of inputting and editing, but data and settings that are already stored in the FlashROM should be unaffected.
E-38 1. While holding down the Fn key and CLR key , push down the reset switch for about 3 seconds with the pen (stylus) until the message shown below appears on the display . T o cancel the full reset operation, press the L T rigger key . R T rigger Key 2.
E-39 DT -X8 Specifi cations Model: DT -X8-10E/10C/11E/1 1C/20E/20C/21E/21C/40E/40C/41E/41C CPU: Marvell ® PXA320 624MHz Memory: 128MB RAM, 256MB Flash ROM (user de fi ned: 160MB) OS: Microsoft ® W indows ® Embedded CE 6.0 R3 operating system Display: 6.
E-40 Bluetooth ® : Protocol: Bluetooth ® Speci fi cation V er .2.0 + EDR Communication Range: Approximately 3 m (9'10 3 / 8 ") (depends on radio wave conditions and environment) Output: 4dBm max. (PowerClass2) WLAN: Standards: IEEE 802.1 1b/g Diffusion Modulation: DS: 802.
E-41 W eight: DT -X8-10E/10C/20E/20C: Approximately 280g (9.9oz) (when battery pack is installed) DT -X8-11E/1 1C/21E/21C: Approximately 285g (10.1oz) (when battery pack is installed) DT -X8-40E/40C: Approximately 290g (10.2oz) (when battery pack is installed) DT -X8-41E/41C: Approximately 295g (10.
E-42 Dimensional Drawings Approx. 65.7mm (2 9 / 16 ") (Display) Approx. 32.4mm (1 1 / 4 ") (Display) Approx. 41.2mm (1 5 / 8 ") Approx. 57.4mm (2 1 / 4 ") (Grip) Approx. 187mm (7 3 / 8 ") Approx. 35mm (1 3 / 8 ") (Grip) DT -X8-10E/10C/11E/1 1C/20E/20C/21E/21C Approx.
E-43 Handling the Hand Belt (HA-K95HB) An optional hand belt (HA-K95HB) can be attached to the terminal. Attaching the hand belt 1. As shown in the fi gure, align the metal part of the hand belt hook in line with the installation position on the terminal and then snap it into the ditch.
E-44 Using the USB Cradle (HA-K60IO) The optional USB Cradle (HA-K60IO) makes it possible to transmit system data and fi le data between the Handheld T erminal and a PC via a USB connection (download or upload). Y ou can also use the USB Cradle to charge the battery pack installed in the Handheld T erminal.
E-45 1 USB Client Port This port is used to transmit system data and fi le data (download, upload) by connecting the Cradle to a PC using a USB cable (DT -380USB-A). A dedicated driver must be installed in the PC before connecting the Cradle to the PC.
E-46 Connecting the USB Cradle Power Supply Use the optional AC adaptor (AD-S15050B) for the power supply of the USB Cradle. Always make sure to connect the AC adaptor to the USB Cradle before performing communication with the Handheld T erminal. Power to the Handheld T erminal is supplied from the USB Cradle.
E-47 4. T urn on the power switch on the right side of the USB Cradle. The power LED on the front of the USB Cradle lights red. 5. Align the terminals on the bottom of the DT -X8 with the power supply terminals in the USB Cradle before inserting the DT -X8 ( ).
E-48 Important! Allowing the power supply terminals become wet can cause an electric shock or fi re. In addition, if the terminals become soiled, contact may be impaired resulting in poor charging.
E-49 Specifi cations 1. USB Protocol: USB V er1.1 Standard T ransfer Rate: 12Mbps (max.) 2. Charging Charging Method: Constant current/voltage Charge Period: Approximately 4 hours 3. Power Supply Power Source: AC adaptor (AD-S15050B) Consumption Current: 5V DC approximately 3.
E-50 Using the Ether net Cradle (HA-K62IO) The optional Ethernet Cradle (HA-K62IO) makes it possible to transmit system data and fi le data between the Handheld T erminal and a PC via a USB or LAN connection (download or upload). Y ou can also use the Ethernet Cradle to charge the battery pack installed in the Handheld T erminal.
E-51 1 USB Client Port This port is used to transmit system data and fi le data (download, upload) by connecting the Ethernet Cradle to a PC using a USB cable (DT -380USB-A). The dedicated driver must be installed in the PC before connecting the Ethernet Cradle to the PC.
E-52 Connecting the Ethernet Cradle Power Supply Use the optional AC adaptor (AD-S42120B/AD-S42120C) for the power supply of the Ethernet Cradle. Always make sure to connect the AC adaptor to the Ethernet Cradle before performing communication with the Handheld T erminal.
E-53 4. Before using the cradle ports, remove the caps from the ports. When using a LAN, connect one end of the LAN cable to the LAN port and the other end to the PC or hub. When using a USB connection, connect one end of the USB cable (DT -380USB-A) to the USB port and the other end to the PC.
E-54 Status of Indicator 1 on DT -X8: Orange: Charging the battery pack. Red Flashing: Standby due to battery pack error or the surrounding temperature is out of the charging temperature range. (charging begins when the temperature is within the char ging temperature range) Green: Charging the battery pack is complete.
E-55 Specifi cations 1. LAN Speci fi cations Communications protocol: IEEE 802.3 Media type: 10base-T/100base-TX auto-switched 2. USB Protocol: USB V er1.1 Standard T ransmission Rate: 12Mbps (max.) 3. Charging Charging Method: Constant current/voltage (the charging circuit is built in DT -X8) Charge Period: Approximately 4 hours 4.
E-56 Using the Cradle-type Dual Battery Charger (HA-K36DCHG) The optional Cradle-type Dual Battery Charger (HA-K36DCHG) can concurrently charge two battery packs installed in the respective DT -X8s. General Guide Side Upper 4 3 1 Bottom 4 2 5 6 7 Bundled Items Use these bundled items to join multiple chargers together .
E-57 1 AC Adaptor Jack Connect the AC adaptor (sold separately) here. 2 Power Switch T urns the power on and off. 3 Connectors Use these connectors to connect multiple Cradle-type Dual Battery Chargers to each other .
E-58 Charging Battery Pack Use the optional AC adaptor (AD-S90190C) to supply power to the charger . 1. Plug the connector from the AC adaptor into the AC adaptor jack on the dual battery charger with the engraved side of the connector facing upwards.
E-59 4. Place DT -X8 in the charger as illustrated so that the terminals on the bottom of the DT -X8 make contact with the power contacts of the charger . T ake care not to trap objects such as the hand strap in the charger . The power LEDs on the top of the charger light green and indicator 1 lights orange.
E-60 Important! W ater or moistur e on the power contacts can cause a short-circuit and/or fi re. Soil on the power contacts will deteriorate the conduction causing poor charge performance.
E-61 Connecting Multiple Cradle-type Dual Battery Chargers Y ou can connect up to three Cradle-type Dual Battery Chargers. Doing so makes it possible to supply power to all the Cradle-type Dual Battery Chargers using one dedicated AC adaptor .
E-62 Important! Each unit of the charger comes with one piece each of the side and bottom brackets. After you join two chargers together using these two brackets, one side bracket and one bottom bracket will be left over . Keep these as spare for use in future.
E-63 Using the USB and Charging Unit (HA-K65US) The optional USB and Charging Unit (HA-K65US) makes it possible to transmit system data and fi le data between the Handheld T erminal and a PC via a USB connection (download or upload). Y ou can also use the USB and Charging Unit to char ge the battery pack installed in the Handheld T erminal.
E-64 Mount and use the USB and Charging Unit as described in the procedure below . Mounting the USB and Charging Unit 1. Fit the USB and Charging Unit onto the bottom of the terminal as shown in the illustration. 2. After mounting the unit onto the terminal, check that it is fi rmly locked in place using the stoppers.
E-65 Removing the USB and Charging Unit 1. Unlock the stoppers on the left and right sides of the USB and Charging Unit by pressing them inwards, as shown in the illustration. 2. Keeping the stoppers pressed in, pull the USB and Charging Unit of f the terminal.
E-66 Charging the Battery Pack The battery pack installed in the DT -X8 can be charged using the USB and Charging Unit with the optional AC adaptor (AD-S15050B).
E-67 Specifi cations Charging: Charging Method: Constant current/voltage Charge Period: Approximately 4 hours (AD-S15050B) Approximately 8 hours (USB-computer connection) Power Supply: Power Source: AC Adaptor (AD-S15050B*) Consumption Current: 5V DC approximately 3.
E-68 Using the Dual Battery Charger (HA-F32DCHG) The optionally available Dual Battery Charger (HA-F32DCHG) can be used to simultaneously charge two battery packs.
E-69 Charging Battery Pack Use the separately sold AC adaptor (AD-S42120B/AD-S42120C) for the power supply of the Dual Battery Charger . 1. Plug the cord from the AC adaptor into the AC adaptor jack of the Dual Battery Charger . 2. Plug the AC cord into a wall outlet.
E-70 Connecting Multiple Dual Battery Chargers Y ou can connect up to three Dual Battery Chargers. Doing so makes it possible to supply power to all the Dual Battery Chargers using one dedicated AC adaptor . 1. As shown in the illustrations below , remove the connector covers of the Dual Battery Chargers you want to connect to each other .
E-71 Specifi cations 1. Charging Speci fi cation Charging Method: Constant current/voltage Charge Period: Approx. 4.5 hours (1 battery pack, normal temperature) When charging two battery packs: Approx. 5 hours (2 battery packs, normal temperature) 2.
E-72 Using Rechargeable Battery Pack HA- K23XLBA T Important! Store a battery pack in its special soft case whenever you are not using it. If the battery pack has been left over unused for a long period of time, the capacity remained decr eases due to spontaneous discharge or chemical decomposition by the battery pack itself.
CASIO COMPUTER CO., L TD. 6-2, Hon-machi 1-chome Shibuya-ku, T okyo 151-8543, Japan.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Casio DT-X8 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Casio DT-X8 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Casio DT-X8 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Casio DT-X8 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Casio DT-X8, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Casio DT-X8.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Casio DT-X8. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Casio DT-X8 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
