Manuale d’uso / di manutenzione del prodotto MG6320 del fabbricante Canon
Vai alla pagina of 25
PIXMA MG6300 Setup Guide © CANON INC. 2012 series.
Setup Guide This guide provides information for setting up a network connection for the printer . Network Connection Wireless Connection Preparation for Connection Printer Setup Setup Procedure Select.
Network Connection W ireless Connection a Preparation for Connection Before Starting Wireless Connection Setup 1. Make sure that the printer is turned on.
2. Flick the screen left or right, then tap the WLAN setup icon. The (blue) Wi-Fi lamp (A) lights up when wireless connection is enabled. c Setup Procedure Selection The printer will automatically search for access points supporting WPS (Wi-Fi Protected Setup).
d -A Push Button Method d Connection Using WPS 1. Press and hold the WPS button on the access point. For details on pressing the WPS button, refer to the access point manual. 2. T ap Start setup on the printer within 2 minutes. The (blue) Wi-Fi lamp on the printer fl ashes while searching for or connecting to the access point.
d -B Standar d setup d Connection via Standard setup 1. T ap Standard setup. 2. T ap your access point. 3. One of the screens below will be displayed on the printer . 4. T ap the screen. 5. Enter the network password (WEP key or passphrase). Character entry is case-sensitive.
d -C WPS d Connection Using WPS 1. T ap WPS. 2. T ap Push button method. 3. T ap OK. 4. Press and hold the WPS button on the access point. For details on pressing the WPS button, refer to the access point manual. 5. T ap OK on the printer within 2 minutes.
d -D Other setup (Advanced setup) d Connection via Advanced setup 1. T ap Other setup. 2. T ap Advanced setup. 3. T ap your access point. 4. T ap the security protocol used by the access point. Disable 5. When the left screen appears, tap OK. The network connection setup is now complete.
WEP 5. T ap the WEP key number you want to use. 6. T ap the screen. 7. Enter the WEP key . Character entry is case-sensitive. 8. T ap Apply . 9. Make sure that the WEP key is correct. 10. T ap OK. 1 1. When the left screen appears, tap OK. The network connection setup is now complete.
WP A/WP A2 5. T ap the screen. 6. Enter the passphrase. Character entry is case-sensitive. 7. T ap Apply . 8. Make sure that the passphrase is correct. 9. T ap OK. 10. When the left screen appears, tap OK. The network connection setup is now complete.
W ired Connection a Preparation for Connection Before Starting Wired Connection Setup 1. Make sure that the printer is turned on. If the power is on, the POWER lamp (A) will be lit. Notes on Wired Connection Make sure that the computer and router (A) (or access point) are connected.
c Printer Setup 1. If the HOME button (A) on the printer is lit, touch the HOME button. 2. Flick the screen left or right, then tap Setup. 3. Flick the screen up or down, then tap Device settings. 4. T ap LAN settings. 5. T ap Change wireless/wired. 6.
Character Entr y Y ou can enter the characters when the keyboard is displayed on the printer . Follow the procedure below . 1. Y ou can enter the characters when the keyboard is displayed on the printer's LCD. Password entry is case sensitive. : T ap to switch between "lower case letters" and "numbers and symbols.
T roubleshooting Standar d setup The T arget Access Point is Not Detected Is the network device (router , etc.) turned on? If the network device is already turned on, turn it off, then turn it back on. Check the access point name/network name and network password of your access point or router .
When using multiple access points: T ap Use multiple AccessPoints. An Unknown Access Point is Displayed Access points in use nearby may also be detected. The Access Point Name is Not Displayed Properly Access point names with double-byte characters are not displayed properly .
WEP Failed to connect to the access point. Make sure that the WEP key entered for the access point is correct. In addition, when using WEP key number 2, 3 or 4 of the access point, set to use WEP key number 1, or select a WEP key number by entering wireless connection settings of the printer directly .
WP A/WP A2 Failed to connect to the access point. Make sure that the passphrase entered for the access point is correct. If the problem is not resolved, there may be other causes. See also the sections below: If the DHCP function of the access point is inactive, enable the DHCP function and confi gure wireless connection settings again.
T o perform Standard setup again 1. T ouch the HOME button (A). 2. Flick the screen left or right, then tap the WLAN setup icon. .
WPS Cannot connect. Connections are being attempted from multiple access points simultaneously . The screen appears when connections are being attempted from multiple access points simultaneously . W ait for a while, then confi gure WPS settings again.
Advanced setup The T arget Access Point is Not Detected Is the network device (router , etc.) turned on? If the network device is already turned on, turn it off, then turn it back on. Check the access point name/network name and network password of your access point or router .
When using multiple access points: T ap Use multiple AccessPoints. An Unknown Access Point is Displayed Access points in use nearby may also be detected. The Access Point Name is Not Displayed Properly Access point names with double-byte characters are not displayed properly .
WEP Failed to connect to the access point. Make sure that the WEP key entered for the access point is correct. In addition, when using WEP key number 2, 3 or 4 of the access point, set to use WEP key number 1, or select a WEP key number by entering wireless connection settings of the printer directly .
The device may not be able to connect to the network in the following cases: If the DHCP function of the access point is inactive, enable the DHCP function or specify the IP address (IPv4 only) of the printer and confi gure wireless connection settings again.
WP A/WP A2 Failed to connect to the access point. Make sure that the passphrase entered for the access point is correct. If the problem is not resolved, there may be other causes. See also the sections below: If the DHCP function of the access point is inactive, enable the DHCP function and confi gure wireless connection settings again.
T o perform Advanced setup again 1. T ouch the HOME button (A). 2. Flick the screen left or right, then tap the WLAN setup icon. .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Canon MG6320 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Canon MG6320 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Canon MG6320 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Canon MG6320 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Canon MG6320, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Canon MG6320.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Canon MG6320. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Canon MG6320 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
