Manuale d’uso / di manutenzione del prodotto AL2810 del fabbricante Campbell Hausfeld
Vai alla pagina of 32
Airless Paint Systems Please read and save these instructions. Read car efully before attempting to assemble, install, operate or maintain the pr oduct described.
2 Operating Instructions and Parts Manual Airless Paint Systems Description Airless paint sprayers are capable of spraying a wide variety of latex, oil- based, and alkyd paints, as well as stains, preservatives and other non- abrasive finishes.
Airless Paint Systems 3 Operating Instructions and Parts Manual General Safety Information (Cont.) 4. Do not smoke or eat when spraying paint, insecticides, or other flammable substances. 5. Always work in a clean environment. T o avoid injury and damage to the workpiece, do not aim the spray gun at any dust or debris.
4 Operating Instructions and Parts Manual Airless Paint Systems General Safety Information (Cont.) ● Paints and solvents containing HA LOG ENA TE D H Y DR OC AR BON S c an react explosively with aluminum. Do not use halogenated hydrocarbons with this equipment .
Airless Paint Systems 5 Operating Instructions and Parts Manual Pr e-Operation (Cont.) 5. Open the prime valve to the open - "Priming Position". This will allow for an easy start. Refer to Figure 1 on page 4. 6. T urn the engine ON/OFF switch to ON.
6 Operating Instructions and Parts Manual Airless Paint Systems www .chpower .com Pr e-Operation (Cont.) flow rate or capacity the sprayer can accommodate.
7 Airless Paint Systems Operating Instructions and Parts Manual www .chpower .com Operation ST ARTING UP 1. Learn the functions of the controls (see “How to Spray / Important Components” for more information). 2. Prepare the Material a. Prepare the material according to material manufacturer's recommendations.
8 Operating Instructions and Parts Manual Airless Paint Systems www .chpower .com Operation (Cont.) d. For long term shutdown or storage, refer to page 4. Be sure to r elieve pressure in the pump after filling with mineral spirits. SPRA Y TECHNIQUE Good Spray Gun T echnique is at the core of any spray paint operation.
9 Airless Paint Systems Operating Instructions and Parts Manual www .chpower .com Electrical System (Cont.) and remove knob. 5. Using a 1/2” nut driver or 1/2” deep socket, remove nut from pressure control shaft. This will allow removal of electrical control board from frame.
10 Operating Instructions and Parts Manual Airless Paint Systems www .chpower .com Service FLUID PUMP FLUID PUMP DISCONNECT 1. Flush out the material you are spraying, if possible. 2. Follow the Pressure Relief Procedure on page 3. Stop the pump in the middle of down stroke.
11 Airless Paint Systems Operating Instructions and Parts Manual www .chpower .com halves. This will disconnect piston rod from connecting rod and gearbox assembly . 3. Screw the suction nut off the pump and remove inlet valve assembly . 4. Using the rod collar tool, loosen the packing nut (CCW) and push the piston down and out of the fluid body .
12 Operating Instructions and Parts Manual Airless Paint Systems www .chpower .com Service (Cont.) Disconnect hose from fluid section. 5. Disconnect and remove fluid section from gearbox, including Connecting Rod Assy . (See"Fluid Pump Disconnect, page 10) 6.
13 Airless Paint Systems Operating Instructions and Parts Manual www .chpower .com Maintenance (Cont.) Inspect the packing nut daily . If seepage of paint into the packing nut and/or movement of the piston upward is found (while not spraying), the packing nut should be tightened enough to stop leakage only , but not any tighter .
Operating Instructions and Parts Manual Airless Paint Systems 14 www .chpower .com Coarse spray Excess ive fo gging (overspray) Pattern too wide Pattern too narrow T oo much material T oo little mater.
15 Airless Paint Systems Operating Instructions and Parts Manual www .chpower .com AL2810 There is spl ittin g from the gun. Paint leaks into the we t cup.
Operating Instructions and Parts Manual 16 www .chpower .com AL2810 STEP 1: Ensure that the pressure control knob is in the maximum (fully clockwise) position.
Operating Instructions and Parts Manual 17 www .chpower .com AL2810 Notes.
18 For Replacement Parts, Call 1-800-626-4401 See Figur es 10 & 11 on pages 10 & 11 for mor e Part Numbers in Diagrams Please provide following information: -Model number -Serial number (if any) -Part descriptions and number as shown in parts list Address parts correspondence to: Campbell Hausfeld 100 Production Drive Harrison, OH 45030 U.
19 Operating Instructions and Parts Manual www .chpower .com AL2810 Ref. No. Description Part Number Qty . 1 007 Gun with swivel (Optional) 120-201XL 1 2 50’ x 1/4” Hose (Optional) 100-011 1 3 50.
20 Operating Instructions and Parts Manual www .chpower .com AL2810 Power Unit Assembly Part No. 301-530.
21 Operating Instructions and Parts Manual www .chpower .com AL2810 301-530 Ref. No. Description Part Number Qty . 1 Sleeve bearing 301-047 1 2 Shield front 301-189 1 3 Coupling set assembly 189-046A .
22 Operating Instructions and Parts Manual www .chpower .com AL2810 Frame Assembly Part No. 301-515 13 11 1 12 2 3 4 10 9 8 7 6 5.
23 Operating Instructions and Parts Manual www .chpower .com AL2810 301-515 Ref. No. Description Part Number Qty . 1 Frame weldment 301-510 1 2 Axle 5/8 x 21.81 188-367 1 3 Spacer 5/8 ID 113-031 2 4 Wheel 13 x 500-6T 301-165 2 5 Set collar 5/8 ID 143-029 2 6 Centerlock nut 5/16-18 100-317 2 7 Rubber foot 163-008A 2 8 Spacer .
24 Operating Instructions and Parts Manual www .chpower .com AL2810 7 8 9 Engine Assembly Part No. 301-524 2 3 4 5 6 1 301-524 Ref. No. Description Part Number Qty .
25 Operating Instructions and Parts Manual www .chpower .com AL2810 Clutch Replacement Parts Ref. No. Description Part Number Qty . 1 Cog belt 301-231 1 2 Clutch 301-264 1 3 Screw 305-088 1 4 Shoulder.
26 Operating Instructions and Parts Manual www .chpower .com AL2810 Clutch Assembly Ref. No. Description Part Number Qty . 1 Screw-Differential 112-041 1 2 Coupling nut assembly 112-054 1 3 Spacer 301.
27 Operating Instructions and Parts Manual www .chpower .com AL2810 Ball V alve Part No. 100-119 100-119 Ref. No. Description Part Number Qty . 1 Handle 100-162 1 2 Screw 100-163 1 3 Ball 100-164 1 * .
28 Operating Instructions and Parts Manual www .chpower .com AL2810 Manifold Filter Part No. 111-200-99 111-200-99 Ref. No. Description Part Number Qty .
29 Operating Instructions and Parts Manual www .chpower .com AL2810 Suction Assembly - 5 Gallon Part No. 301-090-99 Suction Assembly - 55 Gallon Part No.
30 Operating Instructions and Parts Manual www .chpower .com AL2810 Notes.
31 Operating Instructions and Parts Manual www .chpower .com AL2810 Notes.
32 Operating Instructions and Parts Manual www .chpower .com AL2810 Limited Warranty 1. DURA TION: From the date of purchase by the original purchaser as follows: Standard Duty Paint Application Syste.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Campbell Hausfeld AL2810 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Campbell Hausfeld AL2810 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Campbell Hausfeld AL2810 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Campbell Hausfeld AL2810 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Campbell Hausfeld AL2810, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Campbell Hausfeld AL2810.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Campbell Hausfeld AL2810. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Campbell Hausfeld AL2810 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
