Manuale d’uso / di manutenzione del prodotto 2000 del fabbricante Cadillac
Vai alla pagina of 19
2000 Cadillac D e Ville Outer Wheelhouse Sectioning 1-12 Inner Front Pillar Sectioning 1-9 Inner Center Pillar Sectioning 1-10 Outer Front Pillar Sectioning 1-2 Outer Center Pillar Sectioning 1-4 Rear.
2000 cadillac deville 1-1 Outer Front Pillar , Center Pillar and Quarter Panel Sectioning CAUTION: When performing service on or near the Supplemental Inflatable Restraint (SIR) components or the SIR wiring, the SIR system must be disabled.
Outer Front Pillar Sectioning Removal Procedure IMPORTANT: Sectioning should be performed only in the recommended areas. Failure to do so may compromise the structural integrity of the vehicle. 1. Visually inspect and restore as much of the damage as possible to factory specifications.
Installation Procedure IMPORTANT: Remove all foam prior to welding this section of the service panel. 1. Prepare mating surfaces. 2. Apply weld-through primer to mating surfaces prior to assembly. 3. Weld backing plates to vehicle at rocker. IMPORTANT: Replace hinge pillar blocks prior to welding outer panel.
Outer Center Pillar Sectioning Removal Procedure IMPORTANT: Sectioning should be performed only in the recommended areas. Failure to do so may compromise the structural integrity of the vehicle. 1. Locate an approved sectioning area in the center pillar (Fig.
Installation Procedure 1. Install sleeves on vehicle at rocker and center pillar areas using plug welds. 2. Replace hinge blocks and bolts. 3. Prepare mating surfaces. IMPORTANT: Prior to refinishing, refer to the publication GM4901M-D-2000 “GM Approved Refinish Materials” for recommended products.
1-6 2000 cadillac deville Quarter Panel Sectioning Removal Procedure The service part comes with lower quarter panel extension and taillamp pocket attached. These parts can be left on the vehicle if not damaged. Drill out factory welds on the car and service part and use the outer panel only.
2000 cadillac deville 1-7 Preparation Of Service Part 1. Cut service part in corresponding locations to fit original cut lines. Leave a gap of one-and- one-half times the metal thickness of sectioning joint (Fig. 1-9). 2. Create 100␣ mm (4␣ in) backing plate on rocker panel from unused portion of service part.
1-8 2000 cadillac deville Inner Front Pillar , Center Pillar and Rear Wheelhouse Sectioning Fig.␣ 1-11 — 2000 DeVille Inner Frame Sectioning Locations CAUTION: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled.
2000 cadillac deville 1-9 Inner Front Pillar Sectioning Removal Procedure IMPORTANT: Sectioning should be performed only in the recommended areas. Failure to do so may compromise the structural integrity of the vehicle. 1. Visually inspect and restore as much of the damage as possible to factory specifications.
1-10 2000 cadillac deville Installation Procedure 1. Prepare mating surfaces. IMPORTANT: Prior to refinishing, refer to the publication GM4901M-D-2000 “GM Approved Refinish Materials” for recommended products. Do not combine paint systems. Refer to paint manufacturer’s recommendations.
2000 cadillac deville 1-11 Preparation of Service Part 1. Cut center pillar at laser weld location. This will allow a 25␣ mm (1␣ in) overlap to the vehicle for welding (Fig. 1-16). 2. Notch the weather strip flange to prevent excessive metal thickness in these areas.
1-12 2000 cadillac deville Outer Wheelhouse Sectioning Removal Procedure 1. Locate horizontal laser-weld line in upper quarter area (Fig. 1-18). 2. Measure down 25␣ mm (1␣ in) and scribe a cut line. 3. On the vehicle rocker area, locate and scribe a vertical cut line in the recommended section area.
2000 cadillac deville 1-13 Rear Rail Sectioning The rear rail is available as a complete assembly. It consists of an outer panel, two inner reinforcements, a rail extension, and all necessary component mounting brackets (Fig. 1-20). The outer panel and rear mounting brackets are also available separately to facilitate sectioning.
1-14 2000 cadillac deville Removal Procedure 1. Visually inspect and restore as much of the damage as possible to factory specifications. 2. Remove all related panels and components. 3. Cut the rear rail along the rearward flange of the crossbar (Fig.
2000 cadillac deville 1-15 Installation Procedure 1. Using the original part as a guide, mark a line on the service rail 35␣ mm (1-5/16␣ in) forward of the cut made to the original part; this should be approximately 535␣ mm (21␣ in) without the extension attached to the rail.
1-16 2000 cadillac deville ZERO LINE A B C D E F ALL LENGTHS MEASURED FROM Ø LINE AT TOP HINGE 19 MM HOLE ALL MEASUREMENTS HOLE CENTER TO CENTER 19 MM GAGE HOLE Ø Engine Compartment Dimensions – 2.
2000 cadillac deville 1-17 Ø C A B D E F G 540 469 552 526 925 888 1752 2537 3191 1092 348 358 537 496 504 427 430 496 553 577 D A TUM LINE WIDTH HEIGHT LENGTH Underbody Dimensions – 2000 Cadillac .
1-18 2000 cadillac deville ø A B C D E F D A TUM LINE 829 840 827 836 0 0 1140 1140 2183 849 591 930 964 665 1004 WIDTH HEIGHT LENGTH Body Side Dimensions – 2000 Cadillac DeV ille Description Locat.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Cadillac 2000 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Cadillac 2000 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Cadillac 2000 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Cadillac 2000 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Cadillac 2000, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Cadillac 2000.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Cadillac 2000. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Cadillac 2000 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
