Manuale d’uso / di manutenzione del prodotto 9000 del fabbricante Cabletron Systems
Vai alla pagina of 26
9031125-03 SmartSwitch 9000 9C114 and 9C714 Chassis Installation Guide.
.
i Notice Notice Cabletron Systems r eserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletr on Systems to determine whether any such changes have been made.
Notice ii FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference r eceived, including interference that may cause undesir ed operation.
iii Notice Dec laration of Conf ormity Addendum Application of Council Directive(s): 89/336/EEC 73/23/EEC Manufacturer ’s Name: Cabletron Systems, Inc. Manufacturer ’s Address: 35 Industrial Way PO Box 5005 Rochester, NH 03867 European Repr esentative Name: Mr.
Notice iv.
v Contents Chapter 1 Installing the 9Cx14 Chassis The SmartSwitch 9000 .................................................................................................. 1-1 Features ....................................................................
Contents vi.
1-1 Chapter 1 Installing the 9Cx14 Chassis This document contains information necessary to install the SmartSwitch 9000 9C1 14 and 9C714 chassis. It is designed for the initial installation only .
Installing the 9Cx14 Chassis 1-2 Redundant P ower Supply Modules The 9C1 14 and 9C714 support the installation of two power supplies for power supply redundancy and load sharing. If a 9C500 Power Box is used, up to six power supplies may be installed.
1-3 Installing the 9Cx14 Chassis The descriptions of the seven backplane buses are as follows: System Management Bus 1 The System Management Bus 1, abbreviated SMB-1, is a management bus devoted solely to transferring management information between the modules in the chassis.
Installing the 9Cx14 Chassis 1-4 The Cell T ransfer Matrix (installed in the 9C714 chassis onl y) The Cell T ransfer Matrix provides a T ime Division Multiplexed (TDM) based mesh of full duplex, high speed (1.6 Gbps) dedicated interconnections capable of carrying standard A TM cell traffic.
1-5 Installing the 9Cx14 Chassis Site Guidelines The following guidelines must be followed to select a suitable site for the SmartSwitch 9000. If not, unsatisfactory network performance may result. The site must have an unrestricted fr ee surface area around the SmartSwitch 9000 chassis, allowing for free movement of air .
Installing the 9Cx14 Chassis 1-6 Installation Or der Once a suitable site has been chosen, the SmartSwitch 9000 may be installed. The unit may be free standing or rack mounted. It is recommended that the SmartSwitch 9000 installation pr oceed in this order: 1.
1-7 Installing the 9Cx14 Chassis Rac k Mounting the Chassis The chassis can be mounted in a standard 19-inch equipment rack. If the rack is not secured to the floor , it is r ecommended that the SmartSwitch 9000 be installed in the bottom half of the rack.
Installing the 9Cx14 Chassis 1-8 Installing a P ower Suppl y At least one power supply must be installed on the rear of the MMAC-Plus chassis. Additional power supplies can be added to achieve redundancy .
1-9 Installing the 9Cx14 Chassis Figure 1-3. Installing a P ower Suppl y 100-125v-12A 200-250v-6A 50-60 Hz POWER SUPPLY MODULE 9C214-1 100% 50% 0% STA TUS P W R S N B Load Securing Screw Tab Securing .
Installing the 9Cx14 Chassis 1-10 Attaching the Electr ostatic Discharge (ESD) Wrist Strap The ESD W rist Strap must be attached before handling the Envir onmental Module or SmartSwitch 9000 Interface Modules. In addition, observe all precautions when handling these modules to pr event damage from ESD.
1-11 Installing the 9Cx14 Chassis Installing the En vironmental Module The Environmental Module is installed in the slot above the module car d cage in the front of the SmartSwitch 9000 chassis, as shown in Figur e 1-5, by following the steps below: 1.
Installing the 9Cx14 Chassis 1-12 Figure 1-5. Installing the En vironmental Module Installing Smar tSwitch 9000 Interface Modules SmartSwitch 9000 Interface Modules can be installed in any of the 14 slots that are available. T o install Interface Modules, follow the steps below: 1.
1-13 Installing the 9Cx14 Chassis 5. Install the Interface Module in the chassis by sliding it in any available slot and locking down the top and bottom plastic tabs, as shown in Figure 1-6. T ake car e that the Interface Module slides in straight and properly engages the backplane connectors.
Installing the 9Cx14 Chassis 1-14 Attaching 9C614 INB T erminator Modules T wo 9C614 INB T erminator Modules must be attached to the rear of the SmartSwitch 9000 chassis when Interface Modules that use the INB are inserted in the front of the chassis.
1-15 Installing the 9Cx14 Chassis Figure 1-7. Attaching the INB T erminator Modules P owering up the Smar tSwitch 9000 The SmartSwitch 9000 chassis is powered up by following the steps below: 1. Plug one end of the power cord (supplied with the power supply) into the AC power socket on the lower right front corner of the power supply .
Installing the 9Cx14 Chassis 1-16 5. Check that all LEDs on the INB T erminator Module ar e green. If the LEDs are any color other than gr een, refer to the INB T erminator Module Installation Guide . 6. Check that the Status and Alarm LEDs on the Environmental Module are green.
1-17 Installing the 9Cx14 Chassis W eight Unit: 19.96 kilograms (44 pounds) Shipping: 24.95 kilograms (55 pounds) 9C714 MMA C-Plus Chassis Dimensions 76.2 H x 48.3 W x 49.3 D centimeters (30 H x 19 W x 19.4 D inches) W eight Unit: 19.96 kilograms (44 pounds) Shipping: 24.
Installing the 9Cx14 Chassis 1-18 9C614 INB T erminator Module Dimensions 21.59 H x 2.22 W x 14.92 D centimeters (8.5 H x 0.875 W x 5.875 D inches) W eight Unit: 0.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Cabletron Systems 9000 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Cabletron Systems 9000 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Cabletron Systems 9000 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Cabletron Systems 9000 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Cabletron Systems 9000, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Cabletron Systems 9000.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Cabletron Systems 9000. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Cabletron Systems 9000 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
