Manuale d’uso / di manutenzione del prodotto INSTALLATION GUIDE OWNER'S GUIDE del fabbricante Bulldog Security
Vai alla pagina of 14
INSTALLATION GUIDE • OWNER'S GUIDE JBS Technologies produces the world's most innovative and reliable car alarms, remote starters, keyless entry systems and starter immobilizers. JBS Technologies is not an importing or distribution company.
YOUR WARRANTY Here's how your warranty works: JBS Technologies warrants to the original customer, and the original car a limited lifetime warranty. Within 12 months of purchase, JBS Technologies will repair or replace, our option, any defective system at no charge.
REMOTE CONTROL STARTER CONTENTS 26 RS700 3 ATTENTION : We urge you to immediately place this card in your wallet. PROGRAMMING FUNCTIONS FOR YOUR WALLET OR GLOVE BOX WARRANTY VALIDATION Mail to: JBS Te.
4 25 SYSTEM FEATURES Four-Button Remotely start your car to run the heater or air Extended Range conditioning from an extended distance. Remote Control Keyless Entry Remotely locks and unlocks your power door locks. Trunk Release Remotely opens your trunk with a push of a button.
24 5 Your system includes: 1-Installation & Operation Guide 1-Main Control Module 1-Four Button Remote Transmitter with Slide Protector 1-(4) Relay Harness with Relays 1-18-Pin Wire Harness 1-Hood.
6 23 It is recommended that a carbon monoxide detector be installed in the living area near the location where the vehicle may be garaged. Since there are many different makes and models of vehicles, look at the wiring chart on our website, www.jbstech.
22 7 MAKING CONNECTIONS 1. Strip back two inches of insulation on the wire from the remote starter. 2. Strip back one inch of insulation on the wire you need to connect to. 3. Separate the vehicle wire as shown. Make the separation large enough to fit the other wire through.
8 21 MAKING CONNECTIONS cont. 4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. 3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown.
20 9 For wiring charts please visit our website, www.jbstech.com. CONSTANT POWER (+12V, key in any position including off) Make all connections as close to the ignition switch harness as possible. These wire(s) are in your vehicle’s main ignition harness, usually located on the steering column coming from the ignition switch.
10 19 ACCESSORY WIRE(S) THAT POWER THE HEATER/BLOWER MOTOR (+12V in run or on positions) This wire is also in the main ignition switch harness usually located in the steering column. Make all connections as close to the ignition switch harness as possible.
18 11 LOCATING & MAKING CONNECTIONS AUXILIARY INPUT If you wish to use this starter with an aftermarket alarm, connect the BLUE wire from the 18-pin harness to the second or third channel (-) output of your existing alarm. When the output is activated, a (-) signal will be supplied to the remote starter.
12 17 MECHANICAL NEUTRAL SAFETY SWITCH (Rear Wheel Drive Only) When installing a Bulldog remote starter on GM vehicles or Dodge Dakotas built prior to 1996, you must: Use the diagram below to create a circuit that will prevent the remote starter from starting the vehicle unless the key is removed from the ignition switch.
16 13 CONNECTING THE 18-PIN HARNESS & 4-RELAY HARNESS OPTIONAL CONNECTIONS CONNECTING “TYPE B LOCKS” • If your vehicle has a “ Type B ” door locking system, connect the GREEN WITH BLACK STRIPE wire from the 18-pin harness to the door lock wire.
14 15 ANTENNA PLACEMENT FACTORY ANTI-THEFT SYSTEMS FOR GENERAL MOTORS CARS ONLY System 1 : PASSKEY or VATS system (1985 and up). This system has a resistor pill in the key. Measure resistance of the pill using a test meter. A bypass module is available, Module 791.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Bulldog Security INSTALLATION GUIDE OWNER'S GUIDE insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
