Manuale d’uso / di manutenzione del prodotto 50075 del fabbricante ADT Security Services
Vai alla pagina of 55
B Document # 50075 3/13/95 Rev: Product Inf ormation, Installation, Pr ogramming and Operation Manual Security Systems ® UNI•COM Universal Digital Alarm Comm unicator/T ransmitter f or the Unimode .
2 Document # 50075 Rev B 3/13/95 Don't For get Installation Precautions.
3 Document # 50075 Rev B 3/13/95 T ab le of Contents NFPA Standards, UL Documents 5 1.0 Product Description 6 1.1 Product Features 6 Figure 1-1: UNI•COM Assembly 7 1.2 Controls and Indicators 8 Figure 1-2: Controls and Indicators 8 1.3 Compatible Panels 8 1.
4 Document # 50075 Rev B 3/13/95 T ab le of Contents 3.3 Programming Options 18 Table 3-1: Start and End Monitoring Address 20 Table 3-2: Event Codes, Primary Number 23 Table 3-3: Event Codes, Primary Number 24 4.0 Operating Instructions 25 4.1 Normal Mode 25 4.
5 Document # 50075 Rev B 3/13/95 This digital communicator has been designed to comply with standards set forth by the following regulatory agencies: • Underwriters Laboratories Standard UL 864 • .
6 Document # 50075 Rev B 3/13/95 1.0 Pr oduct Description The UNI•COM Universal Digital Alarm Communicator/Transmitter may be used with compatible (refer to Appendices) ADT fire alarm control panels (FACPs). The UNI•COM transmits system status to the UCS (Universal Communication System) via the public switched telephone network.
7 Document # 50075 Rev B 3/13/95 Figure 1-1: UNI•COM Assembly Connector on back of board Primary Phone Line Secondary Phone Line Modular Cables P/N MCBL-7 (Order Separately) Make No Connection 24 VD.
8 Document # 50075 Rev B 3/13/95 Front Panel Switches CLEAR Digits 0-9 TEST A MODE B Up Arrow C Down Arrow D 1st EVENT E ENTER/STORE F Displays • EIA-485 - yellow LED • COMM.
9 Document # 50075 Rev B 3/13/95 The UNI•COM circuit board contains a CPU, other primary components and wiring interface connectors. 1.5.1 Power Requirements Operating voltage for the UNI•COM must be power-limited, filtered, nonresettable 21.2 to 28.
10 Document # 50075 Rev B 3/13/95 DC Power - TB1, Terminals 1 & 2 24 VDC (nominal) filtered, non-resettable and power-limited. Voltage range is 21.
11 Document # 50075 Rev B 3/13/95 If the control panel causes harm to the telephone network, the telephone company reserves the right to temporarily discontinue service. Advance notification will be provided except in cases when advance notice is not practical.
12 Document # 50075 Rev B 3/13/95 Industry Canada (IC) Compliance - "This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
13 Document # 50075 Rev B 3/13/95 Figure 2-1: Wiring Phone Jacks Note: Shorting bars inside RJ31X Jack removed during male plug insertion Secondary Phone Line PH-2 Primary Phone Line PH-1 7 foot Cable.
14 Document # 50075 Rev B 3/13/95 Relay Driver The UNI•COM's open collector output on TB3, terminal 2 is provided for Communi- cator Failure and UNI•COM trouble. It can be used to drive UL listed relay MR-101/ C or MR-201/C. The output is rated for 40 mA and is power-limited.
15 Document # 50075 Rev B 3/13/95 SLC Loop to Fire Alarm Control Panel Earth Grnd Comm Fail +24 VDC M-300 Series Monitor Module TB3 DACT MR-101/C (MR-201/C may also be used) Note: 1) M-300 Series Monitor Module is used to supervise Normally Closed output of M-101/C.
16 Document # 50075 Rev B 3/13/95 Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.
17 Document # 50075 Rev B 3/13/95 Programming of the UNI•COM is possible at any time including while the UNI•COM is communicating with a central station. The UNI•COM has a built-in programmer. All programming selections are stored in nonvolatile Electrically-Erasable Programmable Read-Only Memory (EEPROM).
18 Document # 50075 Rev B 3/13/95 Primary phone number. (00-15) The first sixteen addresses, 00-15, are factory set to 'F' (from 00_F to 15_F ).
19 Document # 50075 Rev B 3/13/95 Valid entries for both the primary and secondary phone numbers are 0 - F with the numeric digits as dialed numbers and hexadecimal digits (A-F) representing the follo.
20 Document # 50075 Rev B 3/13/95 Secondary Number 24/12 Hour Test Time (49) The test message sent to the Secondary phone number may be sent every 12 or 24 hours. If the message is to be sent every 24 hours, leave the factory default entry of zero. If a 12 hour test report time is needed, enter 1=12 hours.
21 Document # 50075 Rev B 3/13/95 AC Loss Reporting Delay (60) '1' is factory default which causes a 6 hour time delay for AC loss reporting.
22 Document # 50075 Rev B 3/13/95 Programming Event Codes (99-168) A description of the type of reports with reported 'event code' that are sent to the central station appear in Tables 3-2 and 3-3. Entering a transmit selection of '0' will cause the communicator to inhibit transmission of the report.
23 Document # 50075 Rev B 3/13/95 T able 3-2: Event Codes, Primar y Number Note: 1) Setting of 0 = do not transmit report to UCS 2) Setting of 1 = transmit report to UCS 3) Reports transmitted to the .
24 Document # 50075 Rev B 3/13/95 T able 3-3: Event Codes, Secondary Number Note: 1) Setting of 0 = do not transmit report to UCS 2) Setting of 1 = transmit report to UCS 3) Reports transmitted to the.
25 Document # 50075 Rev B 3/13/95 4.0 Operating Instructions The UNI•COM has six Modes of operation; Normal, Program, Walktest, Troubleshoot, Type and Lamp Test. Upon initial power up, the system will be in Normal Mode. This section discusses operation of the UNI•COM in the Normal Mode.
26 Document # 50075 Rev B 3/13/95 This key along with the UP Arrow and DOWN Arrow keys, are used to display UNI•COM fault conditions. Press the 1st EVENT key at any time to display the first event that occurred. Use the DOWN Arrow key to view other UNI•COM fault events (older) that have occurred and are active - not cleared yet.
27 Document # 50075 Rev B 3/13/95 Primary Line Secondary Line Modem LED Primary Active Kiss-Off LED Secondary Active LED 4.1.3 Normal Mode Operation : Normal mode is the standard mode of operation. In this mode, the UNI•COM monitors host FACP status, power input, EIA-485 communications and telephone line voltage.
28 Document # 50075 Rev B 3/13/95 The UNI•COM meets NFPA 72 for Remote Station Protective Signaling Service and central station Signaling Service reporting requirements for: (a) the type of signal (b) condition and (c) location of the reporting premises.
29 Document # 50075 Rev B 3/13/95 The 'general' reports for general fire, general supervisory and general fault are always transmitted (unless disabled).
30 Document # 50075 Rev B 3/13/95 EIA-485 Communications Trouble Report The UNI•COM supervises the integrity of the information received from the FACP via the EIA-485 communications bus. Should the communications bus malfunction, the UNI•COM transmits the report '485 comm trouble.
31 Document # 50075 Rev B 3/13/95 Zone or Point Restoral Report Zone or point restoral reports are not transmitted to the UCS unless the zone or point is fully cleared of both alarm and trouble conditions. Walktest Begin and End Reports • Serviceman Walktest: Once a correct Serviceman Code is entered, Walktest Mode may be entered.
32 Document # 50075 Rev B 3/13/95 The UNI•COM will not transmit any system walktest data unless the UCS receiver (central station) first acknowledges receipt of the Begin Walk Test report. This is an added precaution to insure that the walktest data is not misinterpreted at the central station as a live report.
33 Document # 50075 Rev B 3/13/95 4.3.1 Disabling of Zones or Points This feature is primarily used when system points have been defined as remote reset, acknowledge, silence or drill switches. Refer to the FACP Technical Manual for additional information.
34 Document # 50075 Rev B 3/13/95 A handset may be temporarily connected across transformer T1 as indicated in Figure 4-2. The handset, when connected across T1, may be used only as an amplifier/speaker or telephone with the UNI•COM used for number dialing.
35 Document # 50075 Rev B 3/13/95 Addr es s es 16 an d 41 F or mat Ty pe A DT UCS Re c e i v er Fa c tory Def ault 0 ADT F SK II Model # E Re vi si on # E913 Software R evis i on # 31893 The table below shows UL listed receivers compatible with the UNI•COM: 5.
36 Document # 50075 Rev B 3/13/95 ❑ 00 ❑ 01 ❑ 02 ❑ 03 ❑ 04 ❑ 05 ❑ 06 ❑ 07 ❑ 08 ❑ 09 ❑ 10 ❑ 11 ❑ 12 ❑ 13 ❑ 14 ❑ 15 Addresses 00 to 15 store the Primary Phone Number. Enter 'F' to represent the end of the number.
37 Document # 50075 Rev B 3/13/95 ❑ 69 ❑ 70 ❑ 71 ❑ 72 User 1 Walk Test Code. Valid entries are 0-9 ❑ 73 User 1 Walk Test Transmit Enable: Enter '0' for no transmit of walktest events; '1' for transmit. ❑ 74 ❑ 75 ❑ 76 ❑ 77 User 2 Walk Test Code.
38 Document # 50075 Rev B 3/13/95 ❑ 99 ❑ 100 ❑ 101 ❑ 102 ❑ 103 ❑ 104 ❑ 105 ❑ 106 ❑ 107 ❑ 108 ❑ 109 ❑ 110 ❑ 111 ❑ 112 ❑ 113 ❑ 114 ❑ 115 ❑ 116 ❑ 117 ❑ 118 ❑ 119.
39 Document # 50075 Rev B 3/13/95 ❑ 00 ❑ 01 ❑ 02 ❑ 03 ❑ 04 ❑ 05 ❑ 06 ❑ 07 ❑ 08 ❑ 09 ❑ 10 ❑ 11 ❑ 12 ❑ 13 ❑ 14 ❑ 15 Addresses 00 to 15 store the Primary Phone Number. Enter 'F' to represent the end of the number.
40 Document # 50075 Rev B 3/13/95 ❑ 69 ❑ 70 ❑ 71 ❑ 72 User 1 Walktest Code. 'F' for no user identified. ❑ 73 User 1 Walktest Transmit Enable. '0' for no transmit. ❑ 74 ❑ 75 ❑ 76 ❑ 77 User 2 Walktest Code. 'F' for no user identified.
41 Document # 50075 Rev B 3/13/95 Programming Reference Sheet Factory Default ❑ 99 ❑ 100 ❑ 101 ❑ 102 ❑ 103 ❑ 104 ❑ 105 ❑ 106 ❑ 107 ❑ 108 ❑ 109 ❑ 110 ❑ 111 ❑ 112 ❑ 113 ❑.
42 Document # 50075 Rev B 3/13/95 NOTE: The UNI•COM is capable of reporting 198 points when used with the Unimode 200. Use chart to carefully identify supervisory points and remote switches in the system. Identify these points using Type Mode (refer to Section 4.
43 Document # 50075 Rev B 3/13/95 Appendix B: Zone Assignments (Unimode 200 & Unimode 4-16) NOTE: The UNI•COM is capable of reporting 56 zones when used with the Unimode 200 or Unimode 4-16. Use chart to carefully identify supervisory zones. Identify these zones using Type Mode (refer to Section 4.
44 Document # 50075 Rev B 3/13/95 Appendix C: Zone Assignments (Unimode II ) NOTE:Use chart to carefully identify supervisory points and remote switches in the system. Identify these 120 zones using Type Mode (refer to Section 4.3 Type Mode). Zone No.
45 Document # 50075 Rev B 3/13/95 The UNI•COM is capable of reporting 198 points or 56 zones when used with the Unimode 200. The UNI•COM may be mounted in the Unimode 200 control panel or remotely in an ADT-ABS8RF or ADT-UBS1F enclosure up to 6000 feet away from the control panel.
46 Document # 50075 Rev B 3/13/95 Notes: 1) This arrangement allows use of the UNI•COM simultaneously with the RTM-8F module. 2) Ferrite cores are recommended for all applications. 3) Recommended wire is 12 AWG to 18 AWG twisted pair. 4) Shielded wire is not required (unless mandated by local AHJ).
47 Document # 50075 Rev B 3/13/95 Install 120 ohm EOL resistor (P/N: 71244) on TB1 terminals 3 & 4 if last or only device on EIA-485 line. P/N 29090 Supervised and Power Limited EIA-485 and power .
48 Document # 50075 Rev B 3/13/95 Figure E-3: MPS-24BPCA Connection to UNI•COM + Cut jumper JP1 to make output nonresettable for use with UNI•COM Filtered, regulated, resettable, power- limited 24.
49 Document # 50075 Rev B 3/13/95 UNI•COM mounting in Unimode II Remove all power from the Unimode II by disconnecting AC and batteries. Install the three supplied nylon support posts for the top an.
50 Document # 50075 Rev B 3/13/95 Figure F-3: EIA-485 Connection EIA-485 (Supervised and Power Limited) TB1 Terminal 3 RS+ Terminal 4 RS- Install 120 ohm EOL resistor (P/ N:71244) across terminals 3 & 4 if last or only device on EIA- 485 line. Note that Terminals 6 & 7 are not used at this time.
51 Document # 50075 Rev B 3/13/95 Figure F-4: 24 VDC Power Connection to UNI•COM MPS-24A TB3-3 + - TB3-4 TB1-2 - TB1-1 + Power (Supervised and Power Limited) UNI•COM TB1-2 - TB1-1 + Power (Supervi.
52 Document # 50075 Rev B 3/13/95 NOTES.
53 Document # 50075 Rev B 3/13/95 NOTES.
54 Document # 50075 Rev B 3/13/95 NOTES.
55 Document # 50075 Rev B 3/13/95.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il ADT Security Services 50075 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del ADT Security Services 50075 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso ADT Security Services 50075 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul ADT Security Services 50075 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il ADT Security Services 50075, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del ADT Security Services 50075.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il ADT Security Services 50075. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo ADT Security Services 50075 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
