Manuale d’uso / di manutenzione del prodotto PSPHA732 del fabbricante Bryant
Vai alla pagina of 16
SMAR T TEMP ® ELECTRONIC THERMOST A T INST ALLA TION AND OPERA TING INSTRUCTIONS Mt. Laurel, New Jersey 08054, USA ● www .luxproproducts.com PSPHA732 52091 HEAT OFF COOL SET SUNDAY WEEKDAY PROGRAM .
5:36 72 T U 1. COMP A TIBILITY Y our PSPHA732 is compatible with Heat Pumps Up to 3 Stages of Heat and 2 Stages of Cooling. This includes Auxiliary and Emergency Heat. It cannot be used with 120 volt heating systems or 3 wire zone valves. Ask your dealer for other LUXPRO thermostats to control those systems.
C A U T I O N: Y our thermostat is protected against normal static electric discharges. T o minimize the risk of damaging the unit in extremely dry weather , touch a grounded metal object before touching your thermostat. 4. INST ALLATION 4.1 TOOLS REQUIRED • #1 Phillips screwdriver (small) • Drill with 3/16-in.
C A U T I O N: • Be careful not to drop the unit or disturb electronic parts. • Leave the door closed while the body is being removed from the base. 9. Route the wires through the open areas in the base plate above the terminals. Hold the base against the wall, with the wires coming through.
NOTE: If you have an electric system and the blower does not operate after installation, verify that the electric/gas option in installer set up is set to Electric, see SETUP OPTIONS. 18. Y our installation is now complete. 5. OPERA TING BASICS 5.1 UP/DOWN CHANGE KEYS • These are the two upper keys, just right of the units display .
• If a second stage of heat is called for , the flashing rate of HEA T increases • If the 3rd stage of heat activates, the display will also flash "AUX " in addition to HEA T flashing. 5.7 COOL • Use COOL mode to control your air conditioner , cooling your home.
5.12.3 CLEAN CYCLE ® • LUX’ s Clean Cycle ® allows you to program a forced air system to flow air through your system’ s filter , cleaning the air in your home, even when heating or cooling is not being utilized.
to accept the displayed start time and advance to the HEA T SET TEMPERATURE, it will flash to show that it may be edited. • The HEA T SET TEMPERATURE will be displayed on the right side of the display with the HEA T indicator visible.
0 to 60 minutes in increments of 3 minutes. Set 0 MIN/HR to allow AUTO control for particular periods while CLEAN is used in others. Set the fan duration to 60 MIN/HR to run the fan continuously for this period. • Press NEXT to advance to the next period.
• Use UP/DOWN keys to adjust the filter limit in 10-hour increments to the recommended value. • Rotate the dial to RUN to finish this setting. 7.3 ENERGY USAGE Y our thermostat records the total number of hours the thermostat has activated heating and cooling with six separate timers.
11 3 to 6 times per hour . A smaller swing number increases the number of cycles, so room temperature is more constant. A larger swing number decreases the number of cycles, saving energy in most cases. 7.6.1 SWING 1 – 1st ST AGE This setting controls when the first stage of heating or cooling turns on and off.
12 board. For reference, there are a table of settings and jumper positions printed there as well. They are described here from J3, the rightmost jumper , to J7, the leftmost jumper .
13 9.1 BA TTERY INST ALLA TION 1. Remove fresh batteries from their carton. 2. Remove body of thermostat from the wall as described in installation. 3. Remove the used batteries if present and replace them within 90 seconds to avoid having to reset the day and time.
14 12. WIRING DIAGRAMS WIRING DIAGRAM NOTES 1. Dashed wires are optional. 2. If an "E" wire was connected to your old thermostat, it should be re-connected to the "E" terminal on the new thermostat, and the optional jumper between "W" and "E" should not be used.
15 HEA T PUMP SYSTEM NEW THERMOST A T AND T APE OFF WITH COMMON TERMINAL CORRESPONDING TERMINALS NOT USED EG YY 2 R OW 1 W 2 B C L AMANA G Y1 RC-RH W1 W2 X1 AMANA PHD-2,-3,-4,or -5 G R W W1 C ARCO / F.
16 DA Y MON MORN DA Y EVE NIGHT MORN DA Y EVE NIGHT MORN DA Y EVE NIGHT TUES WED PERIOD HEA T TIME TEMP . TIME TEMP . COOL DA Y THURS MORN DA Y EVE NIGHT MORN DA Y EVE NIGHT MORN DA Y EVE NIGHT MORN DA Y EVE NIGHT FRI SA T SUN PERIOD HEA T TIME TEMP .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Bryant PSPHA732 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Bryant PSPHA732 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Bryant PSPHA732 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Bryant PSPHA732 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Bryant PSPHA732, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Bryant PSPHA732.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Bryant PSPHA732. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Bryant PSPHA732 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
