Manuale d’uso / di manutenzione del prodotto NuScan 3000 del fabbricante Adesso
Vai alla pagina of 34
Nuscan 3000 Laser Barcode Scanner Programming Manual.
FCC Compliance This equipment has been tested an d found to comply with the limits for a Class A digital device, pursuan t to Part 15 of the FCC Rules. These limits are designed to provide reas onable protection against harmful interference wh en th e equipm ent is operated in a comm ercial environm ent.
1 Table of Contents 1. INTRODUCT ION………………………………………………………… ……………………..……… 2 2. INSTALLATION……………………… ……………………………………………………… ..….
2 Introduction.
Laser barcode scanner com bines the best scanning perfo rmance and value. The de vice pr ovides an accurate, easy, and fast meth od of data en try and data stor age for computerized inform ation systems. It is easy to install and does not req uire software or drivers t o operate.
4 Installation.
Insert the pl ug on the free end of the Com muni cations Cabl e into the appropriate connector on the host as bel ow descri bed: 1. USB Connecti on 5 connect with host 2.
3. RS232 Connection connect with hos t require adapter for power supply NOTE: for Serial port (RS232 ca ble), please plug the power conn ector of 5V power adapter to RS232 cable. 1. Be sure that Host c omputer is tur ned on. 2. Ensure that all connections are secure.
7 Setup from Bar Code Label.
Multi-Interface Functions – 1 OUTPUT FIRMWARE VERSION RESET CONFIGURATI ON TO DEFAULTS 0A 0B OUTPUT MODE – KEYBOARD WEDGE OUTPUT MODE OUTPUT MODE - SERIAL 000600 000601 GOOD READ BEEP T ONE – NO.
Multi-Interface Functions – 2 SCAN MODE – SINGLE SCA N READING MODE SCAN MODE – SINGLE SCA N NO TRIGGER 013300 013301 SCAN MODE – MULTISCA N SCAN MODE – MULTISCA N NO TRIGGER 013302 013303 S.
Interface – KBW WEDGE MODE - AUTO DETECT PC Communication WEDGE MODE – SCAN SET 2 PA SS THRU 000200 000204 TRANSMIT SPEED - 0 TRANSMIT SPEED TRANSMIT SPEED - 25 0000000 0000025 KEYBOARD COUNTRY - .
Interface – Serial - 1 SERIAL BAUD RATE - 2400 BAUD RATE SERIAL BAUD RATE - 4800 000703 000704 SERIAL BAUD RATE - 9600 SERIAL BAUD RATE - 19200 000705 000706 SERIAL HANDS HAKE - NONE HAND SHAKE SERI.
Interface – Serial - 2 SERIAL DATA BITS - 8 PARAMETERS SERIAL DATA BITS - 7 00081 00080 SERIAL STOP B ITS - 1 SERIAL STOP B ITS - 2 00090 00091 SERIAL PARITY - NONE SERIAL PARITY - ODD 001000 001001.
Symbologies On/Off - 1 CODE 11 - ENABLE CODE 11 CODE 11 - DISABLE 01261 01260 CODE 39 ENABLE CODE 39 CODE 39 DISABLE 00221 00220 FULL ASCII EN ABLE F ULL ASC II DI SABLE 00231 00230 13.
Symbologies On/Off - 2 CODE 93 - ENABLE CODE 93 CODE 93 - DISABLE 00621 00620 CODE 128 - ENABLE CODE 128 CODE 128 - DISABLE 00691 00690 CODE 128 ISBT - ENABLE CODE 128 ISBT - DISABLE 00701 00700 CODAB.
Symbologies On/Off - 3 MSI - ENABLE MSI MSI - DISABLE 01151 01150 UPC-A ENABLE UPC/EAN UPC-A DISABLE 00341 00340 UPC-E ENABLE UPC-E DISABLE 00351 00350 EAN-13 ENABLE EAN-13 DISABLE 00361 00360 EAN-8 E.
Symbologies Set Up - 1 CODE 11 ID CHARACTER – “ m” CODE 11 CODE 11 ID CHARACTER – “Z” 0131m 0131Z CODE 11 LASER/CCD REDUNDA NCY - ENABLE CODE 11 LASER/CCD REDUNDA NCY - DISABLE 01321 01320.
Symbologies Set Up – 2 CODE 93 ID CHARACTER – “h” CODE 93 CODE 93 ID CHARACTER – “Z” 0066h 0066Z CODE 93 LASER/CCD REDUNDA NCY - ENABLE CODE 93 LASER/CCD REDUNDA NCY - DISABLE 00681 0068.
Symbologies Set Up – 3 CODABAR ID CHARACTER – ‛ k’ CODAB AR CODABAR ID CHARACTER – ‛ Z’ 0094k 0094Z CODABAR LASER/CCD REDUNDANCY - ENABLE CODABAR LASER/CCD REDUNDANCY - DISABLE 00951 009.
Symbologies Set Up – 4 MSI ISBN ID CHARACTER – ‛ f’ MSI MSI ISBN ID CHARACTER – ‛ Z’ 0053f 0053Z MSI LASER/CCD REDUNDANCY - ENABLE MSI LASER/CCD REDUNDANCY - DISABLE 01251 01250 EXPAND U.
Symbologies Set Up – 5 UPC-E ID CHAR ACTER ‛ c’ UPC/EAN UPC-E ID CHAR ACTER ‛ Z’ 0050c 0050Z EAN-13 ID CHARACTER ‛ e’ EAN-13 ID CHARACTER ‛ Z’ 0051e 0051Z EAN-8 ID CHARACTER ‛ d’.
Symbologies Set Up – 6 UPC/EAN LASER/CCD REDU NDANCY ENABLE UPC/EAN UPC/EAN LASER/CCD REDU NDANCY DISABLE 00541 00540 21.
EDIT SETUP BAR CODES EDIT #1 – STRIP 1 LEADING CHA RACTER ON ALL BAR CO DES THAT S TART WITH ‛ 12345’ EDIT #1 - OFF 0200010100 000010000000 0112345 0B20001 EDIT #2 – STRIP 1 TRAILING CH ARACTE.
MACRO/SPECIAL KEYS SETUP BAR CODES MACRO #1 – FIND ‛ 1’ AND REPLACE WITH ‛ ONE’ MACRO #1 - DISABLED 02010101011ONE 0B20101 MACRO #2 – FIND ‛ 2’ AND REPLACE WITH ‛ TWO’ FOR CODE 39 .
TERMINATION STRING SETUP BAR CODES STRING #1 – TERMIN ATION CHAR - CR STRING #1 – TERM INATION - LF 0202011000$0D 0202011000$0A STRING #1 – TERMINATION CR+LF STRING #1 - DISABLE 0202011000$0D$ 0.
25 Factory Default Setting.
26 Scanner Timing Default RS-232 communication Default Baud rate 9600 Parity None Data Bits 8 Stop Bi t 1 RTS/CTS Off Terminator <CR> Keyboard Wedge Communication Default Terminal Type PC/AT Key.
27 Appendix-A Troubleshooting & Error Beeps.
28 a. Problem: Nothing happe ns when I follow the operating instructions. Possible Cause Possible Solution Interface cables a re loo se Check for loose cable con nections b. Problem: When I connecte d RS23 2 inte rface reader to PC, I could not get power up signal.
29 d. My computer gets a keyboard error whil e booting up. Possible Cause Possible Solution The scanner is dam age d or is no longer functioning. Disconnect the scanner fro m your computer and use you r keyboard only. Reboot your computer. If your computer still gets a keyboard error, then the problem may not be the scanner.
30 f. Problem: The scanne r be eps, but no data is displayed on my computer. Possible Cause Possible Solution Scanner is not programme d for the correct ho st type. Please make sure the scanner i s configured to the appropriate host type by scanning the correspon ding programming barcod e on the User’s Manual.
31 h. Problem: Some of the barcode data is missing di splayed on the host. Possible Cause Possible Solution The scanner’ s tran smit speed is too fast. For RS232, you can set up the scanner’s transmit speed. i. My Caps Lock LED on my keyboard flickers wh en I re ad a bar code.
32.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Adesso NuScan 3000 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Adesso NuScan 3000 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Adesso NuScan 3000 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Adesso NuScan 3000 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Adesso NuScan 3000, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Adesso NuScan 3000.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Adesso NuScan 3000. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Adesso NuScan 3000 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
