Manuale d’uso / di manutenzione del prodotto Car Sea del fabbricante Britax
Vai alla pagina of 17
P2219_R02f.qxd 11/7/2002 10:23 AM Page 1.
T able of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–5 Child Restraint Features . . . . . .
3 2 Safety Information Introduction • Read and understand this information booklet before using this product. T o ensure proper restraint use, stor e this booklet so you can consult it often.
5 4 Safety Information Safety Information • F AILURE TO FOLLOW EACH OF THE FOLLOWING INSTRUCTIONS CAN RESUL T IN YOUR CHILD STRIKING THE VEHICLE’S INTERIOR DURING A SUDDEN STOP OR CRASH. SECURE THIS CHILD RESTRAINT WITH A VEHICLE BEL T AS SPECIFIED IN THIS USER GUIDE.
7 6 Child Restraint Features Child Restraint Features 1 Cover 2 Harness Slots 3 Harness 4 Comfort Pads 5 Harness Retainer 6 Chest Clip 7 HUGS™ Shoulder Pads 8 Buckle 9 Belly Pad 10 Harness Release L.
8 V ehicle Seating Positions V ehicle Safety Belts NOTE: The information in this section only applies to installation with vehicle seat belts. IMPORT ANT : Some vehicles have no seating positions which are compatible with this child restraint, or any other child restraint.
10 11 Installation Installation with LA TCH 1 V erify that your vehicle is equipped with LA TCH anchors. ( Fig A ) • If LA TCH anchors are not installed, you must use standard vehicle belt installation methods. 2 Insert recline bar into holes on rear of restraint ( see page 18 ) .
13 12 Installation Installation Lap-Shoulder Belt Installation Figure A illustrates a typical lap- shoulder vehicle belt configuration. 1 Insert recline bar into holes on rear of restraint ( see page 18 ) . 2 Place the child restraint in a forward facing position on the vehicle seat.
15 14 Installation Installation Lap Belt Installation Figure A illustrates a typical lap belt configuration. 1 Insert recline bar into holes on rear of restraint ( See page 18 ) . 2 Place the child restraint in a forward facing position on the vehicle seat.
17 16 V ersa-T ether™ V ersa-T ether™ W ARNING: A TT ACH THE VERSA-TETHER ONL Y TO TETHER ANCHORS IDENTIFIED BY YOUR VEHICLE MANUF ACTURER AS TETHER ANCHORAGE POINTS. USE OF OTHER LOCA TIONS IS NOT APPROVED OR PERMITTED. • AL W A YS USE THE VERSA-TETHER FOR CHILDREN WEIGHING MORE THAN 50 POUNDS (22.
19 18 Using Restraint Features Using the Buckle Fastening the Buckle 1 Hold the buckle with one hand. 2 Use your other hand to insert one tongue at a time into the buckle. Proper connection is confirmed with a positive click, after inserting the second buckle tongue ( Fig.
21 20 Securing Y our Child Securing Y our Child Once the child restraint has been installed in the vehicle, follow these instructions to secure your child in the child restraint. IMPORT ANT : Before securing your child in the restraint, always check the adjuster area for debris (e.
The buckle has two positions and should be adjusted to fit your child ( Fig. D ). Select the slot closest to, but not under , the child. W ARNING: Do not use position two (2) until child exceeds 50 pounds (22.6 kg)! Remove the buckle, then rethread in appropriate position.
25 24 Care and Maintenance Care and Maintenance Cover Removal 1 Loosen the harness, by lifting the harness release lever while pulling the shoulder straps forward as far as possible. 2 Unhook the shoulder straps from the yoke, on the rear of child restraint.
27 26 Care and Maintenance Care and Maintenance Cleaning the Buckle If your child eats and drinks while in the restraint, you may need to check the buckle periodically and wash out any accumulated debris or dried liquids. THOROUGHL Y RINSE, using warm water ( Fig.
28 W arranty This child restraint was manufactured by Britax. Britax Child Safety , Inc. (“Britax”) warrants this product to the original retail purchaser as follows: LIMITED ONE-YEAR W ARRANTY This product is warranted against defective materials or workmanship for one year from the date of original purchase.
P2219_R02f.qxd 11/7/2002 10:23 AM Page 32.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Britax Car Sea è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Britax Car Sea - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Britax Car Sea imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Britax Car Sea ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Britax Car Sea, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Britax Car Sea.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Britax Car Sea. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Britax Car Sea insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
