Manuale d’uso / di manutenzione del prodotto PP2-5600 del fabbricante ACTiSYS
Vai alla pagina of 41
PP2-5600 and PP2I-5600 User’s Manual Page 1 of 41 Revision 1.0 2003/1 1 From 3JT e ch User ’ s Manual for: PP2-5600 (Serial Modem) PP2I-5600 (Infrar ed &Serial Modem) Revision Issue Date Engineer/Comments 1.0 April 11, 2002 YLYang/Pre-release 1.
PP2-5600 and PP2I-5600 User’s Manual Page 2 of 41 Revision 1.0 2003/1 1 From 3JT ech TABLE T ABLE ............................................................................................ 2 I. INTRODUCTION ....................................
PP2-5600 and PP2I-5600 User’s Manual Page 3 of 41 Revision 1.0 2003/1 1 From 3JT ech I. INTRODUCTION Thank you for purchasing 3JT ech’ s Pega sus III series high-speed modem with Infrared wireless communication.
PP2-5600 and PP2I-5600 User’s Manual Page 4 of 41 Revision 1.0 2003/1 1 From 3JT ech II. 56K ACCESS INFORMATION The International T elecommunications Union (ITU) determines the technical protocols communicatio ns devices must use to interoperate with each other .
Infrared Modem User’s Manual Page 5 of 41 Revision 1.0 2003/1 1 From 3JT ech III. HARDWARE INSTALLATION Before Y ou S tart Please check if the follows are includ e in your Pegasus III packaging .
Infrared Modem User’s Manual Page 6 of 41 Revision 1.0 2003/1 1 From 3JT ech System Requir ements PDA or any hardware devices with IrDA or RS232 serial interface and any of the following Operating System: W indows 95 and above, DOS, Linux, W inCE, Pa lm OS, PSION, Penbex and others … Front V iew 1.
Infrared Modem User’s Manual Page 7 of 41 Revision 1.0 2003/1 1 From 3JT ech take care of the batteries charging . Als o, the main power source will be from the travel char ger .
Infrared Modem User’s Manual Page 8 of 41 Revision 1.0 2003/1 1 From 3JT ech 3) T urn the switch to Serial on the rear of modem. Then please read the Softwar e Installation chapter . Connect the modem to PDA By Serial Port Connect the cable for PDA (PP2-5600 V ersion) to the cradle of your PDA.
Infrared Modem User’s Manual Page 9 of 41 Revision 1.0 2003/1 1 From 3JT ech IV. SOFTWARE INSTALLATION GUIDE For Palm Organiser (1) Hardwar e needed: 1. 3JT ech. Pegasus III series modem 2. Pilot 1000*. Pilot 5000*, Palm Pilot Pers onal*, Palm Pilot Professional*, Palm III and above (IIIe Not include), IBM W orkpad series and TRGPro 3.
Infrared Modem User’s Manual Page 10 of 41 Revision 1.0 2003/1 1 From 3JT ech 8. T ap on Details on the bottom right 9. Next to SPEED tap on the down arrow then select “57,600bps” 10. Go to "V olume" and T ap on the down arrow . Then choose a volume of your choice.
Infrared Modem User’s Manual Page 11 of 41 Revision 1.0 2003/1 1 From 3JT ech 3. T ype in "user’s name", "user’s passw ord", and "phone number" using the onscreen keyboard. 4. Next to CONNECTION choose IR Modem .
Infrared Modem User’s Manual Page 12 of 41 Revision 1.0 2003/1 1 From 3JT ech For W indows CE/Pocket PC (1) Hardware needed 1. Pegasus III (PP2I-5600) IrDA modem 2. W indows CE or Pocket PC devices 3. Phone line 4. Battery or Adaptor (2) POCKET PC Modem setting 1.
Infrared Modem User’s Manual Page 13 of 41 Revision 1.0 2003/1 1 From 3JT ech 11. Choose OK to setting mode. 12. Tap on Next to enter country code, area code and Phone number. 13. Tap on Next, don’t type anything in “Extra dial-string modem commands” if don’t know it.
Infrared Modem User’s Manual Page 14 of 41 Revision 1.0 2003/1 1 From 3JT ech (4) Internet Explor er settings 1. T ap on the St a r t menu and select Internet Explorer . 2. Enter the WWW addr ess and tap on OK (5) Mail settings 1. T ap on the St a r t menu and select Inbox.
Infrared Modem User’s Manual Page 15 of 41 Revision 1.0 2003/1 1 From 3JT ech For Connecting PSION using Serial Cable This section uses PSION 5 as an example. (1) Hardware needed 1. Pegasus III series modem 2. Psion 5 3. Null modem cable (The Serial Cable synchronizes the PSI ON 5 and the Pegasus modem.
Infrared Modem User’s Manual Page 16 of 41 Revision 1.0 2003/1 1 From 3JT ech 3. Make sure the name is "Hayes compatible modem" Speed is "57,600" baud. Connect via is "Serial" and Fax class is "Auto" . T ap on "Initialization" Enter "A TZ" under Init.
Infrared Modem User’s Manual Page 17 of 41 Revision 1.0 2003/1 1 From 3JT ech Enter your Fax number , name and preferred resolution, then check the " Show connection dialog " and tap " OK ".
Infrared Modem User’s Manual Page 18 of 41 Revision 1.0 2003/1 1 From 3JT ech For Connecting PSION using IrDA Port This section uses PSION 618C as an example.
Infrared Modem User’s Manual Page 19 of 41 Revision 1.0 2003/1 1 From 3JT ech 6. Go to System Æ Contr ol Panel Æ Internet and setup your Internet settings.
Infrared Modem User’s Manual Page 20 of 41 Revision 1.0 2003/1 1 From 3JT ech number which is the number you wish to dial (contact your ISP if you don’t have this number .) 8. Under Account, enter your username , password , and confirm 0password .
Infrared Modem User’s Manual Page 21 of 41 Revision 1.0 2003/1 1 From 3JT ech For PENBEX 1. T ip home icon to back to the “M ain Page”. And choose “Console” icon. 2. Chose “Connection” at title bar . 3. Change “COMM Port” to “IrDA”.
Infrared Modem User’s Manual Page 22 of 41 Revision 1.0 2003/1 1 From 3JT ech 5. Setting the mail information. 6. Chose “Network” at title bar . 7. Setting the dial information. 8. T ip home icon to back to the “Main Page”. And choose “Email” icon.
Infrared Modem User’s Manual Page 23 of 41 Revision 1.0 2003/1 1 From 3JT ech 10. T ype the mail information. And then sent the mail to “Outbox”. 1 1. T ip “Email” at title bar . 12. T ip “Record” and chose “Send/Recei ve” to send m ail and receive mail.
Infrared Modem User’s Manual Page 24 of 41 Revision 1.0 2003/1 1 From 3JT ech For SHARP 1. On the Internet Setting Wizard screen, tap “New”. 2. Tap the “Dial-up (Telephone line)” radio button for “Select the connection type”. Then Press “Next”.
Infrared Modem User’s Manual Page 25 of 41 Revision 1.0 2003/1 1 From 3JT ech 4. Tap the “Advanced Setting”. Set the AT-command at “ATDT”, speed at ”57600”, Hardware flow control “not select ”. And tap OK. Then tap “Next”. 5.
Infrared Modem User’s Manual Page 26 of 41 Revision 1.0 2003/1 1 From 3JT ech connection appears. Select dial- up name that you just setting. 10. After the dial tone, you ar e connecting to your ISP now . 1 1. On the Index screen, tap the “Opti ons” menu and then tap “New Account”.
Infrared Modem User’s Manual Page 27 of 41 Revision 1.0 2003/1 1 From 3JT ech 16 On the Index screen, tap . . for a new mail. Tap “OK” after finish the mail.
Infrared Modem User’s Manual Page 28 of 41 Revision 1.0 2003/1 1 From 3JT ech For W indows98/Me/2000/XP The modem comes with a modem driver for W indows 95/98/Me.
Infrared Modem User’s Manual Page 29 of 41 Revision 1.0 2003/1 1 From 3JT ech 3.Check the square “ Do not check my Modem, I will choose in the list ”. Click “ Next ”. 5. Choose” Hard Disk” and Choose “mdm3jir .inf” 。 Then choose “ZyDAS ZD51_RS2 MROM” and Click “ Next ”.
Infrared Modem User’s Manual Page 30 of 41 Revision 1.0 2003/1 1 From 3JT ech 7.Modem installed OK. Click OK . 8. Then set-up the baud rate. Click P r operties to set-up the baud rate in Modem of Contr ol Panel .
Infrared Modem User’s Manual Page 31 of 41 Revision 1.0 2003/1 1 From 3JT ech 10.After Installing the Palm Desktop Or ganizer Software, restart the computer . HotSync Manager should now be running 1 1.Press the HotSync button from the cradle and the data will transfer between your Palm and PC.
Infrared Modem User’s Manual Page 32 of 41 Revision 1.0 2003/1 1 From 3JT ech V. TECHNICAL SUPPORT If you are experien cing a problem with your m odem, try resolving it with the trou bleshooting suggestions preceding this section. If necessary you can c ontact your loca l dealer’s Customer Service.
Infrared Modem User’s Manual Page 33 of 41 Revision 1.0 2003/1 1 From 3JT ech VI. SPECIFICATION Dimensi ons: 2.5"(65m m) x3.7 5"(95mm ) x0.
Infrared Modem User’s Manual Page 34 of 41 Revision 1.0 2003/1 1 From 3JT ech 3JTech. Co., Ltd. L IMITED W ARRANTY z Hardwar e 3JT ech warrants its ha rdware pr oducts to be free from defects in workmanshi p and m aterials.
Infrared Modem User’s Manual Page 35 of 41 Revision 1.0 2003/1 1 From 3JT ech non-compatibility is caused by a “bug” or defect in the third party’ s product.
Infrared Modem User’s Manual Page 36 of 41 Revision 1.0 2003/1 1 From 3JT ech Some countries, states, or provinces do not allow the exclusion or limitation of implied warranties or the limita ti.
Infrared Modem User’s Manual Page 37 of 41 Revision 1.0 2003/1 1 From 3JT ech Appendix A_Windows98 IR setup(R220L/210L/ 200L) This section describes how to use 3JT ech ’ s PP2I infrared modem with ACTiSYS’ s IrDA dungo, which includes ACT -IR220L/210L /200L are IrDA dungos for converting RS232C to an infrared port.
Infrared Modem User’s Manual Page 38 of 41 Revision 1.0 2003/1 1 From 3JT ech “(Infrared COM port or dongle)”, and then in “Infrared Devices” Select “(Generic Infr ared Serial Port or dongle)”. Click on “OK”. 6. At “Infrared T ransceiver”, Select “ACT iSYS I R-220L or ACT i SYS IR-200L”.
Infrared Modem User’s Manual Page 39 of 41 Revision 1.0 2003/1 1 From 3JT ech successfully . 10. Please reboot your computer . 11. Please refer to ACT -IR 200L/220L User ’ s Manual, “Setting Up” - Section B to continue installation.
Infrared Modem User’s Manual Page 40 of 41 Revision 1.0 2003/1 1 From 3JT ech Appendix B_Countr y code setting T ype commands as follow: A TS38=2#g< Decimal Country code > ( A T#H could se.
Infrared Modem User’s Manual Page 41 of 41 Revision 1.0 2003/1 1 From 3JT ech Appendix C_Advanced AT Commands (For Debug) Command Function & Description A TREEP Display EEPROM A TREEP1 0000,256 Clear all EEPROM value to FF A T&T8 Modem send ASCII codes to PC continuous AT & T 1 +++ A T#E1 A T#E0 Hardware noise testing A TS63.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il ACTiSYS PP2-5600 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del ACTiSYS PP2-5600 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso ACTiSYS PP2-5600 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul ACTiSYS PP2-5600 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il ACTiSYS PP2-5600, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del ACTiSYS PP2-5600.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il ACTiSYS PP2-5600. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo ACTiSYS PP2-5600 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
