Manuale d’uso / di manutenzione del prodotto 8781A del fabbricante Bloomfield
Vai alla pagina of 26
p/n 76201 Rev. F ECN-12898 M628 05 0705 cps 628 OWNERS MANUAL for AUTOMATIC COFFEE / TEA BREWERS MODEL : 8781A Includes: Installation Operation Use & Care Servicing Instructions Model 8781A Brewer.
NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged b y skilled personnel before le aving the factory. Upon acceptance of this shipm ent, the transportation company assumes full responsibility for its safe delivery.
MODEL VOLTS 1ø WAT TS AMPS 1ø POWER SUPPLY CORD 8781A 120 VAC 1500 W 12.5 A 6' with NEMA 5-15P 1 TABLE OF CONTENTS SPECIFIC A TIONS Thank You for purchasin g this Bloomfield Industries appliance.
FE AT U R E S AN D OP E R AT I N G CO N T R O L S 2 M628 76201 Owners Manua l 8781A Tea Brewer.
PRECAUTIONS A ND GENERA L INFORMATION 3 WA RNING : Electric Shock Hazard All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock.
INSTALL A TION 4 RE A D THIS C A R EFULL Y BEFORE ST A RTING TH E INST ALLA TIO N Unpack the unit. Inspec t all components for completeness and condition. Ensure that all packing materials have been removed from the unit. Verify that the Spray Head Gasket and Spray Disk are properly installed.
INSTALLATION (continued) 5 NOTE: This equipment must be installed to comply with all applicable federal, state an d local plum bing codes and ordinanc es. WARNING ELECTRIC SHOCK HAZARD: Brewer must be properly grounded to prevent possible shock hazard.
OPERATION Fig. 3 Brewer Operation Diagram 6 M628 76201 Owners Manua l 8781A Tea Brewer.
OPERATION (continued) 7 A. STAR T-UP For initial start-up, o r if the brew er has not been used for an extended period of tim e: ♦ Be sure spray disk and brew ga sket are properly installed in the brew head. ♦ Be sure the w ater s upply is properly connected and the water supply valve is turned ON .
OPERATION (continued) WATER HEATER Water t emperature is s ensed by a thermobulb inserted into the w ater ta nk. This te m peratu re signa l is fed to the mechanical thermostat. The setpoint temperature is adjustable. Heating element is energized by the thermostat.
A. PREP ARATION Examine the coffee brew chamber to verify th at the tall the wire rack is in place. Plac e one (1) genuine Bl oo m f ield paper filter into the w ire rack in the coffee brew chamber. Add a p re-measur ed amount of fresh coff ee grounds.
BREWING TEA 10 A. PREPARATION Exam ine th e tea b rew chamber to verif y that the short the w ire rack is in place. Place one (1) genuine Bloomfield paper filt er into the w ire r ack in the tea brew chamber. Add an amount of fresh tea leaves to the brew chamber appropriate to the desired 1 gallon or 3 gallon brew volume.
CLEANING I N STRUCTIONS PROCEDURE: Clea n Coffee/Tea Brewer PRECAUTIONS: D isconnect brewer from electric power. Allow brewer to cool. FREQUENCY: Daily TOOLS: Mild Detergent, Clean Soft Cloth or Sponge Bristle Brush, Bottle Brush 1. Disconnect brewer from electric power.
TROUBLESHOOTING SUGGEST IONS 12 SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY W ater won't heat Bre w e r un plugged or circ uit breake r tripped Check power sup p l y co rd Check / reset circuit break.
TROUBLESHOOTING SUGGESTIONS 13 SYMPTOM SUGGESTED REMEDY Poor coffee quality Keep brewe r, brew chamber and decanters clean. Install a taste and odor filter in water supply, and replace cartridges regularly . Use a qualit y coffee with a consistent r oast.
SERVICING IN STRUCTIONS CA UTION Electric Shock Hazard Opening access pa ne ls o n this brew ma y e xpose unins ulated electrical com ponents. Disconnect brewer from electrical power before removing any pa nel.
SERVICING IN STRUCTIONS 15 TEMPERATURE ADJUSTMENT Unplug po wer cord or tu rn circuit bre aker OFF. Rem ove top panel. Pull vent tube out of tank lid and insert a thermome ter of know n accuracy in hole. Reconnec t br ewer to electrical po w er. Place empty container under brew chamber.
IMPORTANT: W ater pre ssure must be betw een 20 p.s.i and 90 p.s.i. flowing pressure . If water pressure exceeds t his value, or if water pressure varies greatly, a pressure regulator must be installed in the water supp l y line. IMPORTANT: Before set ting assembly into tank, make sure tank lid gasket is properly seated on flange of lid.
IMPORT A NT: W hen replacing water fa ucet coil, also re place seal gaskets. SERVICING INSTRUCT IONS (continued) 17 REPLACE SOLENOID Symptom: Automatic brewer will not f low water; or, automatic brewer drips continuously from brew head. Unplug power cord or turn circuit breaker OFF .
SERVICING IN STRUCTIONS (continued) 18 REPAIR HOT WATER FAUC E T Remove top panel and turn faucet va lve OF F . Unscrew ae ra tor cap from faucet and remove handle retaining clip. Do not let faucet bod y tur n. Pull bonnet assembly from faucet body. Examin e the interior of the faucet body a nd the sur face of the seat cup.
SERVICING INSTRUCT IONS (continued) 19 CA UTI ON - CHEMICA L BURN HA ZA RD Deliming chemicals are c austic. Wear appropriate protective gloves and goggles during this procedur e. Never siphon deliming chemicals or solutions by mout h. This operation shou ld only be performed by qua lified and ex- perienced service personnel.
8781A EXPLODED VIEWS & PARTS LIST 20 M628 7620 1 Owners Manual 878 1A Tea Brew er.
8781A EXPLODED VIEWS & PA RTS LIST (continued) 21 M628 7620 1 Owners Manual 8781A Tea Brewe r.
8781A SERVICE KITS 22 SERVICE KITS FAUCET REPAIR KITS 82573 Hand le 82575 Seat Cup 82576 Faucet Repair Kit (In cludes Handle, Seat Cup, Spring, Stem , Pin & Bonnet 82682 Retainer Clip 84804 Aera t.
8781A WIRING DIAGRAM 23 M628 7620 1 Owner s Manual 8781A Tea Brewer.
Bl oo mf ie l d Indu st r i es, I nc . Di vis ion of Carri er C om merci al Refr i ger at i on In US and Canada T elephone: 775-698-5700 Fax: 888 -492-2783 Fax: 800 -356-5142 () websi te: www .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Bloomfield 8781A è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Bloomfield 8781A - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Bloomfield 8781A imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Bloomfield 8781A ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Bloomfield 8781A, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Bloomfield 8781A.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Bloomfield 8781A. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Bloomfield 8781A insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
