Manuale d’uso / di manutenzione del prodotto GLIDER 20 del fabbricante Z Microsystems
Vai alla pagina of 35
Doc# 27-0006UM Issued 11/00 Rev 1.0 Z Microsystems FIELD-READY Z Microsystems User Manu al FI ELD-READY GLIDER 20.
Doc# 27-0006UM Issued 11/00 Rev 1.0 1. Use the power and video cables supplied with the Glider to help prevent interference with radio and television reception. The use of cables and adapters may cause interference with electronic equipment in the vicinity of this unit.
Doc# 27-0006UM Issued 11/00 Rev 1.0 ST ARTING POINT 4 Shipment Contents 4 User Manual 4 System Requirements 4 Product Description 5 T ools Required 6 Precautions 6 INST ALL RAILS 7 Slide Removal 7 Ins.
Doc# 27-0006UM Issued 11/00 Rev 1.0 The User Manual comes in two formats: printed hardcopy or CD- ROM. This Manual is also available on the Z Microsystems website (www .zmicro.com). W e recommend you read this manual as follows: Carefully follow the instructions in the Installation chapter for hookup and initial control settings.
Doc# 27-0006UM Issued 11/00 Rev 1.0 PRODUCT DESCRIPTION The LCD display can quickly swing up into a reading position. 5 Star ting P oint The Glider is an advanced space- saving drawer mount high-end rugged liquid crystal display . Specially de- signed quick- release locks hold the compact folded Glider securely in place during storage.
Doc# 27-0006UM Issued 11/00 Rev 1.0 TOOLS REQUIRED PRECAUTIONS Required T ools and Equipment. Flathead screwdriver with about 10" shaft. Phillips screwdriver with about 10" shaft.
Doc# 27-0006UM Issued 11/00 Rev 1.0 SLIDE REMOVAL With the Glider laid on a workbench, press down to release the Z- Locks on each side of the front of the Glider to slide the side rails back. The slide rails will reach a stop about half way back. This is a safety stop to prevent the Glider from sliding out too far while mounted in the rack.
Doc# 27-0006UM Issued 11/00 Rev 1.0 Install Slides At the back of the cabinest frame, tighten the slide mounts to the cabinet frame. Make sure to hold the slide mounts hard against the rack rail. 8 On each slide rail, use a Phillips screwdriver to loosen the two adjust- ment screws toward the back of the slide rail.
Doc# 27-0006UM Issued 11/00 Rev 1.0 Install Glider 9 INST ALL THE GLIDER IN CABINET FRAME The Glider slides should move in and out easily . If not, check alignment of the slider and Z-Lock mount. Pull the two Glider slides out until they lock. Hold the Glider on each side over the back set of rollers, with the front into your stomach.
Doc# 27-0006UM Issued 11/00 Rev 1.0 FINAL ADJUSTMENTS Slide the Glider partially out. Use a flathead screw- driver to slightly move the Z-Locks in toward or out from the Glider , depnding on the need for best fit. While holding the Z-Locks at the proper setting, tighten the screws on the Z-Lock mounts.
Doc# 27-0006UM Issued 11/00 Rev 1.0 11 W ARNING : Be sure all electrical power to the cabinet is off before connecting any of the cables. W ARNING : There is a key guide for alignment on the cables. Be sure the cable plug and receptacles are aligned properly using the key guide.
Doc# 27-0006UM Issued 11/00 Rev 1.0 VERY IMPORT ANT . Hold the top of the display in the vertical position while rotating the latch clockwise to the locked position. Push down on the latch at the base of the display . Then lift the raised latch from its receptical to the unlatched position.
Doc# 27-0006UM Issued 11/00 Rev 1.0 The display can be rotated clockwise to angled positions. The display can also be moved into the horizon- tal position. The control knobs will be on the bottom. 13 The display can be left in the vertical position or tilted back.
Doc# 27-0006UM Issued 11/00 Rev 1.0 Pr otector R emo val 14 The display protector is intended to protect the surface of the screen from damage while in transit or while stowed. The display protector is not intended to be used while the display is in operation.
Doc# 27-0006UM Issued 11/00 Rev 1.0 Oper a tion CONNECTING CABLES TURN ON POWER NOTE: Connecting to non-standard systems will require an adapter . T o obtain a video adapter , contact Customer Services at Z Microsystem, Inc.
Doc# 27-0006UM Issued 11/00 Rev 1.0 Monitor Adjustments INITIAL SETUP AND ADJUSTMENTS The Glider features pushbutton controls on the lower front of the display screen to adjust the bright- ness of the display , to change the image positioning on the screen, and to refine the screen image.
Doc# 27-0006UM Issued 11/00 Rev 1.0 17 This section explains how to use the Glider control buttons to adjust the clarity of the display and image position on the screen. In particular it discusses: The function of each of the pushbutton controls. How to reset previously saved settings or return to factory settings.
Doc# 27-0006UM Issued 11/00 Rev 1.0 Monitor Adjustments 18 V P os Moves the screen image up or down. Clock The Clock controls move the sampling points left or right while maintaining a fixed distance between samplings. These adjustments ensure that the sampling occurs at the peak of the input video signal (i.
Doc# 27-0006UM Issued 11/00 Rev 1.0 19 The Glider can store screen settings for multiple resolutions, which is especially useful when it is used with a graphics card that supports a range of resolutions.
Doc# 27-0006UM Issued 11/00 Rev 1.0 20 Monitor Adjustments Step 1: P ower Up After the installation instructions have been followed: T urn on power to the computer/ workstation. T urn on power to the Glider . The Glider will then: Illuminate the P ower indicator on the front panel.
Doc# 27-0006UM Issued 11/00 Rev 1.0 21 Step 3: Adjust Horizontal Width This is the critical step to ensure a crisp screen image. For a Sharp display , you must adjust the image so that it fits precisely within the boundaries of the screen. T o adjust the horizontal width: 1.
Doc# 27-0006UM Issued 11/00 Rev 1.0 Monitor Adjustments 22 Step 4: Adjust Horizontal P osition Press the SELECT button until the H P os indicator is illuminated, then use t h e a n d buttons to adjust the horizontal position of the screen left or right to center the screen image.
Doc# 27-0006UM Issued 11/00 Rev 1.0 23 T o adjust the screen for the best possible display , try the following: Press the an d buttons until you have a universally fuzzy screen. Count the number of button presses for the screen to go from fuzzy to clear to fuzzy again.
Doc# 27-0006UM Issued 11/00 Rev 1.0 24 Display Head R emo val T o remove the Glider display head, follow these steps: On the back of the display , press the mounting arm button to release the display head locking bar . Rotate the display to the horizontal position.
Doc# 27-0006UM Issued 11/00 Rev 1.0 25 CLEAN MONITOR Gently wipe the covers and the screen with a soft cloth. Remove finger marks and grease with a damp cloth and mild detergent. DO NO T use solvents or abrasives. Never use flammable cleaning material to clean the monitor or other ectrical apparatus.
Doc# 27-0006UM Issued 11/00 Rev 1.0 CLOSE GLIDER Display Sto wa ge Tilt the display head back towards the rear of the rack all the way to the horizontal position. 26 The following describes closing and stowage of the Glider in the cabinet. From the landscape position, rotate the display to the vertical position.
Doc# 27-0006UM Issued 11/00 Rev 1.0 Lower the pivot latch into its recepticle. Slide the Glider into the frame until it snaps into the closed, secure position. Slide the two display linkage locks at the back of the display to the closed position to secure the display .
Doc# 27-0006UM Issued 11/00 Rev 1.0 28 T r oubleshooting NO IMAGE ON DISPLA Y Flip the power switch to on. The circle should be down. Connect the power cable to a 110 vac outlet, which is turned on. Connect the video cable to the computer .
Doc# 27-0006UM Issued 11/00 Rev 1.0 29 FEA TURES Large Display Area Multi-Scan/Sync Capability Wide Viewing Angle Small P ackage Outline Full Color High Contrast Ratio FUNCTION.
Doc# 27-0006UM Issued 11/00 Rev 1.0 Specifica tions 30 PHYSICAL SPECIFICA TIONS Display Dimensions Height 16.7 in (42.4 cm) Width 20.0 in (50.8 cm) Rack Dimensions Height 3.5 in (8.9 cm) Width 19.0 in (48.3 cm) Depth 26.3 in (66.8 cm) Display W eight 23 l bs (10.
Doc# 27-0006UM Issued 11/00 Rev 1.0 31 DISPLA Y SPECIFICA TIONS Display Area Horizontal 15.7 in (39.9 cm) V ertical 12.6 in (32.0 cm) Diagonal 20.1 in (50 cm) Number of Pixels 1280 x 1024, RGB V ertical Stripe Pixel Pitch Horizontal 0.312 mm V ertical 0.
Doc# 27-0006UM Issued 11/00 Rev 1.0 Z Microsystems has achieved full Y2K Compliance. In late 1997, the company s senior management assigned a Y2K Project T eam that consists of a cross -functional .
Doc# 27-0006UM Issued 11/00 Rev 1.0 NOTE: If possible, stay by the computer . The Z Microsystems T echnical Support Representa- tive may wish to go through the problem over the telephone. NOTE: More help, late-breaking news and details of the latest accessories for these products may be found on the worldwide web at: http:// www.
Doc# 27-0006UM Issued 11/00 Rev 1.0 If the Z Microsystems T echnical Support Engineer determines that the product needs to be replaced, a Customer Service Representative will issue a Return Material Authorization (RMA) number and return address. A RMA number is required to return a product to Z Microsystems, regardless of the reason for the return.
Doc# 27-0006UM Issued 11/00 Rev 1.0 Z Microsystems, Inc. 5945 Pacific Center Blvd., Suite 509 San Diego, CA 92121 Phone: (858) 657-1000 Fax; (858) 657-1001 Website: www.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Z Microsystems GLIDER 20 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Z Microsystems GLIDER 20 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Z Microsystems GLIDER 20 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Z Microsystems GLIDER 20 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Z Microsystems GLIDER 20, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Z Microsystems GLIDER 20.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Z Microsystems GLIDER 20. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Z Microsystems GLIDER 20 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
