Manuale d’uso / di manutenzione del prodotto ZKH52251 del fabbricante Yazoo/Kees
Vai alla pagina of 19
1 MANUAL NO. 102936IR PRINTED IN USA COMMERCIAL MOWERS OPERA T OR’S MANUAL FOR: MODELS: ZKH52221 ZKH52251 ZKH61221 ZKH61251 700-800 P ARK A VE. BEA TRICE, NEBRASKA U.
PRINTED IN USA 2 MANUAL NO. 102936IR Congratulations on the purchase of your Kees mower . This manual has been prepared for the owners and operators of the ZT MAX™ 52" and 61" commercial mowers. Read, under- stand and follow the saftey and operating instructions.
3 MANUAL NO. 102936IR PRINTED IN USA T ABLE OF CONTENTS SAFETY : 1 . Training 2. Preparation 3. Operation 4 . T ransport ation 5. Maintenance SETUP AND ADJUSTMENTS: 1. Park brake 2. Cutting height 3. Mower deck leveling 4. Mule drive belt tension 5.Throttle lever tension 6.
PRINTED IN USA 4 MANUAL NO. 102936IR SAFETY TRAINING: 1. Read this manual carefully and question your dealer if something is not clear . 2. Be thoroughly familiar with the controls and proper use of the equipment. 3. Never allow children, teenagers, or people unfamiliar with these instructions to use the mower .
5 MANUAL NO. 102936IR PRINTED IN USA SAFETY TRANSPORT A TION: Use a heavy duty trailer to haul mower . Set park brake, turn of f fuel valve and strap mower to trailer . NOTE: Park brake will not hold mower in place when transporting. Be sure to tie down the mower to the trailer .
PRINTED IN USA 6 MANUAL NO. 102936IR ADJUSTMENTS P ARK BRAKE: 1. S top engine and remove key . Release p ark brake and measure the length of the spring. The distance between the washers on each end of the spring should be 2-7/8" (See Fig 2 ). 2. If adjustment is needed, loosen the nut below the spring.
7 MANUAL NO. 102936IR PRINTED IN USA ADJUSTMENTS MULE DRIVE BEL T TENSION: 1. S top engine and remove the key . 2. Check to make sure the bolt head in the spring loaded idler pulley , on the left side of the engine deck is positioned between the two alignment holes in the left support plate (See Fig 4).
PRINTED IN USA 8 MANUAL NO. 102936IR Figure 5A Figure 5B 5. If adjustment is necessary , loosen the nut against the yoke. Apply slight rearward pressure to the motion control lever and turn the head of the adjustment bolt in the proper direction until the lever is centered in the neutral slot.
9 MANUAL NO. 102936IR PRINTED IN USA ADJUSTMENTS MOTION CONTROL LINKAGE ADJUSTMENT : 1. This adjustment must be made with the drive wheels rotating. Raise rear of the unit and block it up so the wheels are free to rotate. CAUTION: Keep hands, feet and clothing away from rotating tires.
PRINTED IN USA 10 MANUAL NO. 102936IR OPERA TING INSTRUCTIONS NOTE: T o begin motion the operator must be in the seat and the brake disengaged before the levers can be moved from the neutral slots or the engine will kill. By moving the levers an equal amount forward or back the mower will move in a straight line in that direction.
11 MANUAL NO. 102936IR PRINTED IN USA OPERA TING INSTRUCTIONS S T ARTING AND OPERA TION: 1. Operator must be sitting in the seat. Engage park brake, blades off and place the motion control levers in the neutral slots. (See figure 6) 2. Adjust throttle to 1/2 and set choke (if needed) turn key and release as soon as engine starts.
PRINTED IN USA 12 MANUAL NO. 102936IR MAINTENANCE 7. Engine oil: Change oil to manufacturers specifications. S top engine and remove key . Drain oil when engine is warm. Thoroughly clean around cap before removing. Remove oil drain cap from the end of drain hose located at the right rear of unit allow to drain and replace drain cap.
13 MANUAL NO. 102936IR PRINTED IN USA 13. Fuel filter: Replace annually or as needed. 14. Hydraulic filter and oil: Change every 500 hours or yearly . S top engine and remove key . T ilt seat forward and clean around the filter and the fittings under the hydraulic tank.
PRINTED IN USA 14 MANUAL NO. 102936IR.
15 MANUAL NO. 102936IR PRINTED IN USA TROUBLE SHOOTING PROBLEM POSSIBLE CAUSES Engine won’t start Mower will not move or moves slowly or hard 1. Blade switch on. 2. Drive levers not in the neutral slots. 3. Operator not in seat. 4. Park brake disengaged.
PRINTED IN USA 16 MANUAL NO. 102936IR WIRING DIAGRAM.
17 MANUAL NO. 102936IR PRINTED IN USA SERVICE RECORD DESCRIPTION OF WORK DONE DA TE SERVICE DONE BY.
PRINTED IN USA 18 MANUAL NO. 102936IR.
19 MANUAL NO. 102936IR PRINTED IN USA 10. Battery: Check every 25 hours. Check electrolyte level. If needed fill to the full line marked on the side of the battery . Fill with distilled water . Do not try starting the engine with a weak battery . Recharge or replace the battery .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Yazoo/Kees ZKH52251 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Yazoo/Kees ZKH52251 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Yazoo/Kees ZKH52251 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Yazoo/Kees ZKH52251 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Yazoo/Kees ZKH52251, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Yazoo/Kees ZKH52251.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Yazoo/Kees ZKH52251. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Yazoo/Kees ZKH52251 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
