Manuale d’uso / di manutenzione del prodotto X90 6 MFE BL del fabbricante Bertazzoni
Vai alla pagina of 20
INSTALLATION, MAINTENANCE AND USE INSTRUCTIONS FOR FREE-STANDING COOKERS 90x60 cm (type M91/M91V) Model X906MFE* , X906 DUAL*, X906GEV* READ THE INSTRUCTION BOOKLET BEFORE INSTALLING AND USING THE APPLIANCE.
2 CONTENTS: INSTALLER TECHNI CAL MANUAL .................................................................................................... ........... pg. 2 Installing the cooker - In stallation in formation .........................................
3 I MPORTANT INFORMATION FOR INS TALLING THE APPLIANC E The cooker can b e installed separately, as a freest anding unit, on a plin th (Not suitable for X90 6 GEV* and X90 6 DUAL* models), or bet ween kitchen units or be tween a kitchen unit and the wall.
4 This appliance shall be installed only by authori sed persons and in acco rdance with th e manufacturer's installation ins tructions, loca l gas fitting regula tions, municipal building codes , electrical wiring regulations, local water supply regulation s, AS/NZS 5601.
5 WARNING: After completing the abo ve-mentioned replacements, t he technician must ad just the burners, as described in the paragraph below, seal any adjustm ent and pre-adjustment de vices and apply the lab el on the appliance, to replace the existing one , corresponding to the ne w gas adjustme nt.
6 WARNING: If the supply cord is dama ged, it must be replaced by the ma nufacturer or its service agent or a similarly qualified pers on in order to av oid a hazard.
7 To replace the power cable, lift the terminal board ’s cover a nd replace the cable. To access the terminal boar d in cookers with a 3x2.5mm² cable, the back panel on the rear of the appliance must be removed.
8 Note: It is recommended not to try to ignite a burner if the relative fl ame cap is not in the correct position. If the flame does not light after the first attempt, wait 5 minutes for the gas to dissipate before attempting to re-light the burner. Tips for using burners correctly: - Use suitable pots for each bur ner (see tab.
9 then release the knob. M ake sure that the burner remains on, otherwise repeat the o peration. As for cookers without ignition trough knob, press the thermost at knob a nd the key with the spark sy mbol, wait about 10 seconds after the burner has been completely lit and then rel ease the knob.
10 - the symbol indicates that the electric fan, and the oven light have b een turned on . - the symbol indicates that only the oven light is turned o n; USING THE 5 + 0 SWITCH ( only cooker with Dual Enrgy oven) The 5 + 0 switch installed in th e Dual Energy oven models is used, along with the electri c or gas thermostat.
11 - the symbol indicates that only the top external element (1200W) has been turned on; - the symbol indicates the only the bottom element (1800W ) has been turned on; - the symbol indicates that onl.
12 Before cooking, allow the oven to reach the desired te mperature setting wa iting for the orang e light to turn off. This type of oven is equippe d with a circular element around which a fan has been installed th at creates forced-air circul ation in the horizontal direct ion.
13 Grilling on the shelf : In this case, the shelf supplie d is placed on l evel 1 or 2 an d the foods to be gril led are placed on top, while the tray is insert ed on the lo wer levels to collec t the co oking juices. T hen turn on the grill eleme nt switching the thermostat to the relative position (electric oven version).
14 AFTER-SALES TECHNICAL SE RVICE AND SPARE PARTS TECHNICAL SERVICE AND SPARE PARTS Before leaving the factory, this appliance wa s tested and adjusted by specialist skilled staff to give the best operating results. Any subsequent necessary rep airs or adjustments must be carried out with the greatest care and attention by auth orised personnel.
15 Fig. 1 Fig. 3 Fig. 4 Fig. 5 F i g . 6 F i g . 7.
16 F i g . 8 F i g . 9 Fig.10 Fig.11 Fig 12 Fig 13 Fig. 14.
17 Fig 15 Fig. 16 Fig. 17 T Fig. 18 Fig. 19 Fig. 20 Fig. 21 Fig. 22 Fig. 23 Fig. 24 Fig. 25.
18 Fig. 26 Fig. 27 Fig.28a Fig.28b Fig.28c Fig.28d.
19 Fig. 29 Fig. 30 Fig. 31 Fig. 32.
20 OVERALL DIMENSIONS Cod. 310686.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Bertazzoni X90 6 MFE BL è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Bertazzoni X90 6 MFE BL - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Bertazzoni X90 6 MFE BL imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Bertazzoni X90 6 MFE BL ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Bertazzoni X90 6 MFE BL, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Bertazzoni X90 6 MFE BL.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Bertazzoni X90 6 MFE BL. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Bertazzoni X90 6 MFE BL insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
