Manuale d’uso / di manutenzione del prodotto X Class Conversion to WES7 del fabbricante Wyse
Vai alla pagina of 18
Inst allation Guide Wyse ® X Class Conversion to WES7 Wyse ® USB Firmware T ool TM Release 1.10 Issue: 102910 PN: 883887-19L Rev . B.
Copyright Notices © 2010, Wyse T echnology Inc. All right s reserved. This manual and the software and firmware described in it are copyrighted. Y ou may not rep roduce, transmit, transcribe, store i.
Content s 1 Introduction 1 Kit Contents 1 Overview 2 Wyse T echnical Support 2 Related Document ation and Services 2 Wyse Online Community 2 2 Inst alling X90cw Mobile Thin Client Flash and RAM 3 Requ.
iv Contents This page intentionally blank..
1 Introduction This guide provides ste p-by-step in structions to convert X90cw mob ile thin clients from WES2009 to WES7. Caution WES7 firmware r equires X clas s mobile thin clients to have a min imum of 4 GB flash and 2 GB RAM. Tip After converting yo ur mobile thin clients, o btain any available firmwa re update a t http://www .
2 Chapter 1 The Conversion Sof tware Assembly DVD-ROM conta ins: • A PDF of this Reference Guide • Wyse USB Firmware T ool Release 1.10 • X Class WES7 Conver sion Image folder containing the following files: · bios.img · cmos.img · commandsXml.
2 Inst alling X90cw Mobile Thin Client Flash and RAM This chapte r contains inform ation for u sers of Wyse X90cw mobile thin clients who must install new flash and RAM. If you are installi ng firmware only , you can skip this chapter and proceed to"Installing WES7 Firmware.
4 Chapter 2 Figure 2 Removing the flash cover screws 5. Lift the flash cover to remove it and expos e the flash mo dule as sho wn in Figur e 3. Notice that the front of mobile the thin client is positioned at the bottom of the photo. Wa r n i n g Flash modules may be susceptible to da mage by Electro-S tatic Discharge (ESD).
Installing X90cw Mobile Th in Client Flash and RAM 5 9. Remove the screw from the RAM cover usin g a small Phillips Screwdriver as shown in Figure 4. Figure 4 Removing the RAM cover screw 10. Lift the RAM cov er to remo ve it and ex po se the RAM module as shown in Figure 5.
6 Chapter 2 12. Install the new RAM module in the revers e order of removing the original RAM modu le. Carefully press down on the RA M module until its retaining clip s lock it into place. 13. Replace the RAM cover in the reverse order as described in step s 10 and 9.
3 Inst alling WES7 Firmware This chapter include s the requirement s and procedures you nee d to install and use Wyse ® USB Firmware T ool TM to update your mobile thin client to WES7 firmware.
8 Chapter 3 S tep 3: Use Wyse USB Firmware T ool to Config ure a Single USB Key to Inst all Firmware 1. Double-click the shortcu t to run the tool an d open the Wyse USB Firmware T o ol wizard (the welcome p age provides the p roduct version and descriptio n, and a link to view the Wyse end user license agreemen t).
Installing WES7 Firmware 9 4. Select the Windows Embedded S t andard 7 OS type o ption. 5. Select the Up date Firmware operation to perform optio n. Tip Although the Preserve dat a p artition check bo.
10 Chapter 3 Figure 12 Prep are USB drive 11 . Select the USB key onto which you want the configurations (you can use Refresh as needed to recogn ize an inserted USB key), and then click Next . The pr ogress bar s show the ov erall prog ress and task pr ogress.
Installing WES7 Firmware 11 S tep 5: V erifying Mobile Thin Client Operation After the mob ile thin client reboots, yo u can verify the Ve r s i o n and that your general client information is cor rect. Figure 13 Client Info rmation (blank exa mple) 1.
12 Chapter 3 S tep 6: Attach a Wyse Conversion Label and Microso ft License Label on Each Converted Mobile Thin Client The conversion kit is suppl ied with Wyse Conversion Labels and Microsof t License Labels that must be atta ched to each mobile th in client as shown in Figures 14 and 15.
Installing WES7 Firmware 13 T roubleshooting This section contains ge neral troubleshooting information . USB Keys - T roubleshoot ing Boot Issues Due to differ ent manufacturing proce sses on U SB keys (and the variety of them), not all brands have been tested with the Wyse USB Firmware T ool.
Inst allation Guide Wys e ® X Class Conversion to WES7 Issue: 1029 10 Written and publishe d by: Wyse T echnology Inc., October 2010 Created using FrameMake r ® and Acrobat ®.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Wyse X Class Conversion to WES7 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Wyse X Class Conversion to WES7 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Wyse X Class Conversion to WES7 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Wyse X Class Conversion to WES7 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Wyse X Class Conversion to WES7, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Wyse X Class Conversion to WES7.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Wyse X Class Conversion to WES7. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Wyse X Class Conversion to WES7 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
