Manuale d’uso / di manutenzione del prodotto H-2412G del fabbricante Wells
Vai alla pagina of 16
PRINTED IN UNITED ST A TES OF AMERICA WELLS BLOOMFIELD, LLC 2 ERIK CIRCLE, P . O. Box 280 V erdi, NV 89439 www .wellsbloomfield.com telephone: 775-689-5703 fax: 775-689-5976 IMPORTANT: DO NOT DI SCARD.
M228 306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate Unless otherwise specified, all commercial cooking equipment manufactured by WELLS BLOOMFIELD, LLC is warranted against defects in ma terials .
W A R R A N T Y x i S P E C I F I C A T I O N S 1 FEATURES & OPERATING CONTROLS 2 PRECAUTIONS & GENERAL INFORMATION 3 AGENCY APPROVAL INFORMATION 3 I N S T A L L A T I O N 4 I N I T I A L A D .
BURNERS Provide cooking heat Front and rear burners are individually controllable Removable for easy cleaning BURNER CONTROL Provide individual control of front and re ar burners KNOBS PILOT LIGHT Provides ignition source for main burners ACTUATOR Admits gas to burner when depres sed.
This appliance is intended for use in commercial establishments only. This appliance is intended to prepare food for human consumpti on. No other use is recommended or autho rized by the manufacturer or its agents. This hotplate must be installed by a technician qualifie d and certifie d or licensed to install gas-fired equipme nt.
INSTALLATION NOTE: DO NOT discard the carton or other packing materials until you have inspected the appliance for hidden damage and tested it for proper operation. Refer to SHIPPING DAMAGE CLAIM PROCEDURE on the inside front cover of this manual. DANGER: HEALTH HAZARD This appliance must be properly ventilated.
INSTALLATION (continued) GAS APPLIANCE CODE COMPLIANCE The installation of gas piping from the outlet side of the ga s meter or service regulator to the hotplate must be performed by a technician qualified and certified or licensed to install gas-fire d e quipment.
INSTALLATION (continued) INSTALLING THE HOTPLATE Refer to the nameplate. Verify the fuel type and pressure, which must match the nameplate specifications. Conne cting the hotplate to the wrong fuel type and/or pressure will compromise the safety and/or performance of the appliance.
INITIAL ADJUSTMENT SET GAS PRESSURE: Turn the gas shut-off valve OFF . A gas pressure test tap is provided on the gas suppl y manifold. Remove both burner control knobs and the front pan el. Remove plug in gas pressure test tap and attach a manometer.
OPERATION GENERAL OPERATIONAL NOTES Carefully read the description of the hotplate operation on the specification sheet. Do NOT use this appliance if it has been subm erged in water. Call a qualified technician to examine the applia nce and to service or replace any component whi c h has been subme r ged.
WARNING: FIRE HAZARD NEVER attempt to force or repair a stuck control valve. Contact your Authorized Wells Service Agency for repair s. Forced or improperly repaired valves pose the ri sk of fire and/or explosion.
TROUBLESHOOTING 10 SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY Pilot will not light Gas supply off Check main / unit gas valves Air in lines Turn gas valve on.
CLEANING INSTRUCTIONS PREPARATION Turn gas shut-off valve OFF before clea ning. Allow hotplate to cool completely before cleani ng. FREQUENCY: Daily TOOLS Bristle Brush Clean Cloth or Sponge Mild Detergent Cleaner Formulated for Stainless Steel Warm Water CLEANING Turn gas shut-off valve OFF before clea ning.
CLEANING INSTRUCTIONS (continued) 12 Fig. 7 Hotplate Assembly FRONT BURNER Slides over RIGHT nozzle; hooks into FRONT slots on pilot support REAR BURNER Slides over LEFT nozzle; hooks into REAR slots on pilot support GRA TE ASSEMBL Y Sets in place above burners DRIP TRA Y Drops in place exposing tops of burners 1.
DESCRIPTION PART NO. CUST OMER SERVICE DA T A please have this information av ailable if calling for service RESTAURANT ___________ __________________ LOCAT ION _____________ INSTALLATION DATE _______.
Genuine Parts Protect - YOU - All - Ways SER VICE TRAINING - QUALITY SER VICE SER VICE TRAINING - QUALITY SERVICE CUSTOMER SA TISF ACTION CUSTOMER SA TISF ACTION Commercial Food Equipment Service Asso.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Wells H-2412G è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Wells H-2412G - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Wells H-2412G imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Wells H-2412G ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Wells H-2412G, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Wells H-2412G.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Wells H-2412G. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Wells H-2412G insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
