Manuale d’uso / di manutenzione del prodotto WESY99300 del fabbricante Weider
Vai alla pagina of 31
® USER’S MANUAL Model No. WESY99300 Serial No. The serial number is found in the location shown below . Write the serial number in the space above. CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference.
2 LIMITED W ARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 IMPORT ANT PRECAUTIONS W ARNING: T o reduce the risk of serious injury , read the following important precau- tions before using the weight system. 1. Read all instructions in this manual and in the accompanying literature before using the weight system.
4 ASSEMBLED DIMENSIONS: Height: 198 cm Width: 165 cm Depth: 86 cm Low Pulley Station Foot Plate Press Arm Backrest Curl Pad Adjustment Knob Butterfly Arms Weight Stack Leg Press Lever Thank you for selecting the innovative and versatile WEIDER ® PRO 9930 weight system.
5 ASSEMBL Y Make sure you have the following tools: • T wo adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape.
6 1. Before beginning, make sure that you have read and understood the information on page 5. Locate and open the parts bag labelled “FRAME ASSEMBL Y .” Press a 2” Square Inner Cap (38) into the Butterfly Base (61). Press two 2” Square Inner Caps into the Press Base (60).
7 3. Place two Weight Bumpers (84) over the indicated holes in the Butterfly Base (61). Slide the Weight Guides (58) into the indicated holes. Attach the Weight Guides (58) to the Butterfly Base (61) with two 3/8” x 2 1/2” Bolts (6), four 3/8” Flat W ashers (17), and two 3/8” Jam Nuts (18).
8 7. T urn the Seat Brace (75) so the nut is on the side shown. Attach the Seat Brace to the Butterfly Base (61) with the indicated 5/16” x 2 1/2” Carriage Bolts (1) and two 5/16” Nylon Locknuts (2).
9 1 1. Press a 1 1/2” Square Inner Cap (79) into the Press Seat Frame (52). Slide the bracket on the lower end of the Press Seat Frame (52) onto the indicated 5/16” x 2 1/2” Carriage Bolts (1) in the Press Base (60). T ighten two 5/16” Nylon Locknuts (2) onto the Bolts.
14. Open the parts bag labelled “CABLE ASSEMBL Y AND PULLEYS.” For cable identification and routing during steps 14–32, refer to the CABLE DIAGRAMS and CABLE ID CHART on pages 19 and 20. Insert two 3/8” x 1” Bolts (15) into the welded brackets on the Left and Right Butterfly Arms (67, 68).
11 15. Wrap the Short Cable (71) over a “V” Pulley (21) as shown. Attach the “V” Pulley and a Long Cable T rap (14) to one side of the welded bracket on the Butterfly Upright (62) with a 3/8” x 2 1/2” Bolt (6) and a 3/8” Nylon Locknut (4).
12 20. Attach the threaded shaft on the Medium Cable (72) to the Small “U”-Bracket (43) with a 1/4” Flat W asher (1 1) and a 1/4” Nylon Locknut (16). Note: See the inset drawing. Do not completely tighten the Nylon Locknut; it should be threaded only two turns onto the end of the Cable.
13 24. Wrap the Long Cable (73) around a 3 1/2” Pulley (5). Attach the Pulley and a Cable T rap (39) to the indicat- ed bracket on the Butterfly Base (61) with a 3/8” x 2” Bolt (35) and a 3/8” Nylon Locknut (4). 23. Wrap the Long Cable (73) around a 3 1/2” Pulley (5) in the direction shown.
14 26. Wrap the Long Cable (73) around a 3 1/2” Pulley (5) in the direction shown. Attach the Pulley and a Cable T rap (39) to the indicated bracket on the Press Base (60) with a 3/8” x 2” Bolt (35) and a 3/8” Nylon Locknut (4). Make sure that the Cable T rap is ori- ented as shown.
15 29. Wrap the Long Cable (73) around a “V” Pulley (21) in the direction shown. Attach the “V” Pulley and a Long Cable T rap (14) to the small tube on the Press Seat Frame (52) with a 3/8” x 3 1/4” Bolt (28), a 3/8” Flat W asher (17), and a 3/8” Nylon Locknut (4).
16 Seat Assembly 34. Press four 3/4” Round Inner Caps (40) into the ends of the Pad T ubes (48). Insert the Pad T ubes (48) into the indicated holes in the Leg Lever (49) and the Press Seat Frame (52). Slide Foam Pads (47) onto the ends of both Pad T ubes.
17 36. Insert a 1/4” x 1 1/2” Carriage Bolt (82) into the center hole in a Seat Plate (42). Attach the Seat Plate to a Seat (51) with two 1/4” x 3/4” Screws (13). Insert the 1/4” x 1 1/2” Carriage Bolt (82) into the indi- cated hole in the Seat Bar (74) and secure it with a 1/4” Flat W asher (1 1) and a 1/4” Nylon Locknut (16).
18 39. Apply the WEIDER PRO 9930 decal in the location shown. 40. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENT , beginning on page 21 of this manual. Before using the weight system, pull each cable a few times to make sure that the cables move smoothly over the pulleys.
19 CABLE DIAGRAMS The cable diagrams below and on the next page show the proper routing of the Short Cable (71), the Medium Cable (72), and the Long Cable (73).
20 Long Cable (73) 1 2 3 4 5 6 7 8 9 13 11 12 10.
21 USING THE CURL P AD T o use the Curl Pad (69), insert the Curl Post (70) into the Seat Brace (75) and secure the Curl Post at the desired height with the Adjustment Knob (45). A TT ACHING THE LA T BAR OR NYLON STRAP TO THE HIGH PULLEY ST A TION Attach the Lat Bar (50) to the Medium Cable (72) with a Cable Clip (57).
22 Slack can be removed from the Long Cable (73) by relo- cating the indicated 3 1/2” Pulley (5) on the Press Seat Frame (52). T o do this, remove the 3/8” Nylon Locknut (4), 3/8” Flat W asher (17), and 3/8” x 2 1/2” Bolt (6). Re- attach the Pulley at the second or third hole, as needed.
23 High Arm Butterfly Curl/ Leg Raise Weight Pulley Press (lbs.) Low Pulley (lbs.) Plates (lbs.) (lbs.) (lbs.) To p 1 1 20 15 16 17 1 25 39 31 32 37 2 40 59 48 47 56 3 55 78 64 63 76 4 70 97 80 78 95 .
Part No. 173978 R0501A Printed in Canada © 2001 ICON Health & Fitness, Inc. ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-888-936-4266, Monday through Friday , 8 a.m. until 6:30 p.
Note: Assembly is divided into four stages: 1) frame assembly; 2) arm assembly; 3) cable and pulley assembly; and 4) seat assembly . The hardware for each assembly stage is packaged separately . W ait until you begin each stage to open the parts bag for that stage.
1/4" Flat W asher (1 1) 5/16" Flat W asher (19) 3/8" Flat W asher (17) 5/16" x 1 3/4" Bolt (9) 3/8" Nylon Locknut (4) 3/8" Jam Nut (18) 1/4" Nylon Locknut (16) .
1" Retainer (25) 3/8" x 2" Bolt (35) 3/8" x 3 1/2" Bolt (24) 3/8" x 2 1/2" Bolt (6) 3/8" x 3 3/4" Bolt (7) 3/8" x 8" Bolt (30) Cable Clip (57) 3/.
1" Round Inner Cap (41) 1" Round Cap (26) 3/4" Round Inner Cap (40) 1 1/2" Square Inner Cap (79) 1" Inner Cap (80) 1 3/4" Square Inner Cap (37) 2" Square Inner Cap (.
8 1 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. P ART LIST—Model No. WESY99300 R0501A Key No. Qty .
65 13 70 37 25 26 66 37 65 67 18 18 71 25 26 37 18 71 68 15 27 18 69 51 82 42 13 45 2 2 2 88 11 16 19 20 74 2 2 38 73 4 1 39 5 35 1 61 39 5 7 4 4 39 5 35 2 2 4 17 39 5 35 62 4 5 5 22 36 2 6 21 14 38 3.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Weider WESY99300 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Weider WESY99300 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Weider WESY99300 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Weider WESY99300 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Weider WESY99300, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Weider WESY99300.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Weider WESY99300. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Weider WESY99300 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.