Manuale d’uso / di manutenzione del prodotto WESY92190 del fabbricante Weider
Vai alla pagina of 28
USERÕS MANUAL Model No. WESY92190 Serial No. The serial number is found in the location shown below . Write the serial number in the space above. CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference.
Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Before Y ou Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 W ARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
4 ASSEMBLED DIMENSIONS: Height: 77 in. Width: 38 in. Length: 61 in. Low Pulley Station W arning Decal 2 Foot Plate Row Bar Console High Pulley Station Ab Pulley Station Leg Lever Butterfly Arm Press A.
5 Note: This introduction will save you more time than it takes to read it! Identifying Parts T o help you identify the small parts used in assem- bly , we have included a P ART IDENTIFICA TION CHART located in the center of this manual.
6 1. Before beginning assembly , make sure you have read and understood the information on page 5. Open the parts bag labeled ÒFRAME ASSEMBL Y .Ó Press a 2Ó Square Outer Cap (51) onto each end of the Stabilizer (5). Insert two 5/16Ó x 2 3/4Ó Carriage Bolts (14) up through the Stabilizer (5) and place it flat on the floor .
7 4. Press a 2Ó Square Inner Cap (21) into each end of the crossbar on the T op Frame (1). Slide two 5/16Ó Flat W ashers (56) onto two 5/16Ó x 2 3/4Ó Bolts (67). Place the T op Frame (1) on top of the Front Upright (42) and align the indicated holes with the holes in the bracket on the Front Upright.
8 10. Press a 1 1/2Ó Square Inner Cap (33) into the end of the Seat Frame (36). Insert two 5/16Ó x 2 3/4Ó Bolts (67) through the Support Plate (27) and the indicated holes in the Front Upright (42). Place the mounting bracket on the Seat Frame (36) over the two Bolts.
9 13 Lubricate 1 Bracket 47 21 4 3 45 Axle 4 3 45 13. Identify the Right Butterfly Arm (48) and the Left Butterfly Arm (47). Note the position of the welded bracket on each Arm. Arm identification is very important for this step. Lubricate both axles on the T op Frame (1).
Cable Assembly 15. Open the parts bag labeled ÒCABLE ASSEMBL Y AND PULLEYS.Ó For Cable identification and rout- ing during steps 15Ð30, refer to the Cable Diagram and Cable ID Chart on page 19. Identify the High Cable (2). It is approximately 163 1/2Ó long.
11 19. Remove the 1/2Ó Nylon Locknut (68) from the welded hook on the T op Frame (1). Slide the Pulley Bracket (20) onto the hook and secure it with the Nylon Locknut. T ighten the Nylon Locknut, but make sure the Pulley Bracket can pivot freely . Remove the Pulley (35) from the Pulley Bracket (20).
12 22. Remove the 3 1/2Ó Pulley (35) from the pre-assem- bled Adjustment Bracket (84). Wrap the High Cable (2) around the Pulley in the direction shown. Attach the Pulley to the Bracket with a 3/8Ó x 1 1/2Ó Bolt (60) and a 3/8Ó Nylon Jamnut (63). 22 35 63 2 84 60 23.
13 26. Move to the other side of the unit. Wrap the Low Cable (9) around a 3 1/2Ó Pulley (35) in the direction shown. Attach the Pulley to the Front Upright (42) with a 3/8Ó x 3 3/4Ó Bolt (19), a Cable T rap (66), a 3/8Ó Flat W asher (55) and a 3/8Ó Nylon Jamnut (63).
31. Open the parts bag labeled ÒSEA T ASSEMBL Y .Ó Attach the Backrest (41) to the Front Upright (42) with two 1/4Ó x 2 1/2Ó Screws (43) and two 1/4Ó Flat W ashers (90). Seat Assembly 41 43 43 90 42 30. Wrap the Low Cable (9) around a 3 1/2Ó Pulley (35) in the direction shown.
15 34. Attach the Curl Pad (24) to the Curl Post (10) with two 1/4Ó x 3/4Ó Screws (17). Slide the Curl Post (10) onto the Seat Frame (36) so each of the welded brackets is between the Seat Frame and the bracket on the Leg lever (29). Secure the Curl Post with the 5/16Ó x 2Ó Knob (72).
38a. The following instructions are critical to the cor- rect operation of your weight system. If the adjustment is incorrect, it can damage the motor . Make sure that you read and understand these instructions before attempting to adjust the Weight Mechanism (26).
38e.See the inset drawing. Loosen the 3/8Ó Plain Nuts (85), and the 3/8Ó x 3Ó Bolt (88) so that the 3/8Ó x 4Ó T ap Screw (86) can rotate freely . Note: The T ap Screw must pivot freely . 38f. Check the brass piece that is pictured in drawing 38f.
18 41. Make sure that all parts have been properly tight- ened. The use of the remaining parts will be explained in HOW T O USE THE WEIGHT SYSTEM, beginning on page 20 of this manual. Before using the weight system, pull each cable a few times to be sure that the cables move smoothly over the pulleys.
19 Cable Diagram The Cable Diagram below shows the proper routing of the High Cable (2) and the Low Cable (9). The numbers show the correct route for each Cable. Make sure that the Cables are routed correctly , that the Pulleys move smoothly , and that the Cable T raps do not touch or bind the Cables.
20 How to Use the W eight System PLUGGING IN THE POWER CORD Plug in the power cord to a 120-volt outlet. Keep the power cord away from walkways and heated surfaces. T urn on the power when using the weight system, or the weight system could be damaged.
21 A TT ACHING THE LA T BAR, ROW BAR, AB STRAP OR HANDLE TO THE LOW , HIGH OR AB PULLEY ST A TION Attach the Lat Bar (76) to the Low Cable (9) with a Cable Clip (73). For some exercises, the Chain (74) should be attached between the Lat Bar and the Low Cable with two Cable Clips.
22 31 63 66 35 Additional slack can be removed by using the Pulley Plates (31). The Pulley Plates have several sets of adjust- ment holes. By moving one or both pulleys to a different set of holes, the cables will be tightened. T o move a Pulley , remove the 3/8Ó Nylon Jamnut (63) and the 3/8Ó x 1 1/2Ó Bolt (60).
1" Round Inner Cap (49) 1" Round Cover Cap (3) 3/4" Round Inner Cap (34) 3/8" x 2 1/4" Eyebolt (44) 1 1/2" Square Inner Cap (33) 2" Square Inner Cap (21) 2" Squ.
5/16" Nylon Jamnut (91) 3/8" Flat W asher (55) 5/16" Flat W asher (56) 3/8" Nylon Locknut (57) 3/8" Nylon Jamnut (63) 3/8" Plain Nut (85) 1/4" x 2" Bolt (71) 1/.
1" Retainer (4) 1/4" Flat W asher (90) 3/8" x 3Ó Bolt (88) 3/8" x 2 1/4" Bolt (65) 3/8" x 1 3/4" Bolt (60) 3/8" x 3 3/4" Bolt (19) 3/8" x 4 1/2".
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. Part ListÑModel No. WESY92190 R1299A Key No. Qty . Description Key No.
34 34 30 30 44 33 28 30 34 28 30 34 22 71 38 17 37 13 91 33 29 36 74 73 75 45 45 21 21 3 4 4 3 15 6 57 15 48 47 9 11 58 56 53 53 18 5 51 51 14 52 8 53 1 21 21 67 56 65 50 6 63 35 55 54 2 90 43 41 42 2.
Ordering Replacement Parts T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Weider WESY92190 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Weider WESY92190 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Weider WESY92190 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Weider WESY92190 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Weider WESY92190, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Weider WESY92190.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Weider WESY92190. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Weider WESY92190 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
