Manuale d’uso / di manutenzione del prodotto WESY85310 del fabbricante Weider
Vai alla pagina of 27
USER’S MANUAL QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or find that there are missing or damaged parts, we will guarantee you complete satisfaction through direct assis- tance from our factory .
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORT ANT PRECAUTIONS 3 W ARNING: T o reduce the risk of serious injury , read the following important precau- tions before using the weight system. 1. Read all instructions in this manual and in the accompanying literature before using the weight system.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 74 in. Width: 60 in. Length: 54 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arms Squat Arm Decal 1 Decal 1 Decal 2 Press Arm Weight Stacks Backrest VKR Arms Weight Pin Thank you for selecting the versatile WEIDER ® 20CT weight system.
5 Make sure you have the following tools: • T wo adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape.
1. Before beginning assembly , be sure that you have read and understand the information in the box above. Press two 2” Outer Caps (51) onto the indicated locations on the Stabilizer (5). Press two 2” Inner Caps (27) into the indicated ends of the Stabilizer and the Base (4).
4. Set two Weight Bumpers (19) on the bracket on the Base (4) as shown. Set two Weight Bumpers on the bracket on the Stabilizer (5). Stack eight Weights (25) onto each set of W eight Bumpers (19). Be sure that the pin grooves are all on the same side of each stack of Weights.
6 8 Lubricate Holes Pin 73 65 63 64 25 6. Press a Weight Tube Bumper (64) into the end of the other Weight Tube (63). Insert the W eight T ube into the rear stack of Weights (25). Be sure that the pins on the Weight T ube are sitting in the pin grooves in the top Weight (refer to step 4).
9. Wet the handle of one Press Arm (46) with soapy water . Slide a 5” Plastic Grip (83) onto the han- dle. Press a 1” Round Inner Cap (49) into the other end of the handle.
10 12. Press two 1” x 2” Inner Caps (87) into the indicat- ed end of the Squat Arm (84). Attach the Squat Arm (84) to the VKR Upright (74) with a 3/8” x 5 1/2” Bolt (93) and a 3/8” Nylon Locknut (21). Be sure that the indicated brack- et is pointing down as shown.
11 15. Route the Medium Cable (58) around the “V”- Pulley (50) on the Right Arm (48). Be sure that the Cable is in the groove of the Pulley and that the Long Cable T rap (31) is positioned to hold the Cable in place. T ighten the 3/8” x 2 1/2” Bolt (86) and the 3/8” Nylon Locknut (not shown).
12 19. Route the Short Cable (23) around the 3 1/2” Pulley (15) attached to the upper hole in the Press Frame (17). Be sure that the Cable T rap (66) is in the “3 o’clock” position and that the Cable is routed around the Pulley as shown. T ighten the 3/8” Nylon Locknut (21) and 3/8” x 3 1/2” Bolt (not shown).
13 22. Locate the Long Cable (72). Attach the Long Cable to the other Small “U”-Bracket (71) with a 1/4” Nylon Locknut (2) and a 1/4” W asher (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable only a couple of turns, as shown in the inset drawing.
14 24. Wrap the Long Cable (72) around a 3 1/2” Pulley (15). Attach the Pulley and a Cable T rap (66) to the Squat Arm (84) with the 3/8” x 2 1/4” Bolt (94) and a 3/8” Jamnut (92). Be sure that the Jamnut is on the side shown and that the Cable T rap is positioned to hold the Cable in place.
27. Press a 1 1/2” Inner Cap (32) into the Seat Frame (36). Insert a 1/4” x 2” Carriage Bolt (38) into the center hole in the Seat Plate (37). Attach the Seat Plate to the Seat (13) with two 1/4” x 3/4” Screws (18). Insert the 1/4” x 2” Carriage Bolt (38) through the indicated hole in the Seat Frame (36).
16 31. Press two 1 1/2” Inner Caps (32) into the ends of the Left and Right VKR Arms (79, 80). Attach the Left and Right VKR Arms (79, 80) to the VKR Upright (74) with two 5/16” x 3” Bolts (75) and two 5/16” Nylon Locknuts (3). 31 VKR ASSEMBL Y 74 79 32 32 3 75 75 80 32.
17 ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise.
18 A TT ACHING AND REMOVING THE SEA T T o attach the Seat (13), set the bracket on the Seat Frame (36) onto the indicated pins on the Front Upright (42). Attach the Seat Frame to the Front Upright with the 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40).
19 WEIGHT RESIST ANCE CHART This chart shows the approximate weight resistance at each station. “T op” refers to the 6.5 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm.
20 TROUBLE-SHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immedi- ately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.
21 CABLE DIAGRAM The cable diagram below shows the proper routing of the Long Cable (72), the Medium Cable (58), and the Short Cable (23). Use the diagram to be sure that the three cables and cable traps have been assembled cor- rectly .
5/16" Nylon Locknut (3) 1/4" W asher (10) 5/16" W asher (8) 1" Retainer (69) 3/8" W asher (9) 3/8" Nylon Locknut (21) 1/4" x 2" Machine Screw (81) 3/8" Jam.
1/4" x 2 1/2" Screw (43) 5/16" x 2 3/4" Carriage Bolt (14) 5/16" x 2 1/2" Carriage Bolt (1) 1/4" x 2" Carriage Bolt (38) 3/8" x 2" Bolt (12) 3/8".
1" Round Inner Cap (49) 1" Round Cover Cap (70) 1/2" x 3/4" Spacer (61) 5/16" x 2" Eyebolt (35) 1 1/2" Inner Cap (32) 1 3/4" Inner Cap (44) 2" Inner Cap (2.
P ART LIST—Model No. WESY85310 R0901A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty .
68 3 20 21 15 66 12 27 83 78 80 75 75 10 81 77 32 83 78 79 3 10 43 74 11 11 3 51 1 1 27 19 51 21 5 25 64 26 12 66 15 63 65 24 2 71 72 3 67 31 50 76 21 56 54 83 83 52 53 39 21 93 92 15 94 84 3 8 8 22 4.
ORDERING REPLACEMENT P ARTS T o order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be prepared to give the following information: 1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Weider WESY85310 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Weider WESY85310 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Weider WESY85310 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Weider WESY85310 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Weider WESY85310, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Weider WESY85310.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Weider WESY85310. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Weider WESY85310 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
