Manuale d’uso / di manutenzione del prodotto WESY74090 del fabbricante Weider
Vai alla pagina of 27
® USER’S MANUAL Model No. WESY74090 Serial No. The serial number is found in the location shown below . Write the serial number in the space above. CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference.
2 Limited W arranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 W ARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
4 ASSEMBLED DIMENSIONS: Height: 75 in. Width: 31 in. Length: 44 in. Weight Stack Leg Lever Butterfly/Press Arm Foam Roller Seat Backrest Thank you for selecting the versatile WEIDER ® 740 Weight System. The 740 offers a selection of weight stations designed to develop every major muscle group of the body .
5 Note: This introduction will save you more time than it takes to read it! Identifying Parts T o help you identify the small parts used in assem- bly , we have included a P ART IDENTIFICA TION CHART in the centre of this manual.
6 Frame Assembly 1. Before beginning assembly , make sure you have read and understood the information on page 5. Locate and open the parts bag labeled “FRAME ASSEMBL Y .” Press a 1 1/2” Square Outer Cap (27) onto each end of the Stabilizer (5) and place it on the floor as shown.
7 3. Attach the two Weight Bumpers (19) to the Stabilizer (5) with two #8 x 1” Screws (18). Slide the six Weights (25) onto the two tubes on the Weight Guide (62). Note: Make sure all of the Weights are turned so the pin grooves are on the same side and that the grooves are oriented as shown in the drawing.
8 6 6. Attach the two tubes on the Weight Guide (62) to the T op Frame (55) in the following manner: Slide a 5/16” x 6” Bolt (7) through one of the tubes on the Weight Guide (62) until the tip is barely visible on the other side. Position a 1/2” x 1” Spacer (51) and slide the Bolt through it.
9 9 9. Identify the Right Arm (48) and the Left Arm (47) by imagining yourself sitting on the seat. Note the posi- tion of the welded bracket (A) on each Arm. Arm identification is very important for this step. Lubricate both axles on the Press Frame (17).
10 12. Locate the parts bag labeled “CABLE ASSEMBL Y AND PULLEYS.” For cable identification and rout- ing during steps 12 through 27, refer to the Cable Diagram and Cable ID Chart on pages 15 and 16. Slide a 3/8” Flat W asher (9) and a 1/2” x 1/4” Spacer (44) onto a 3/8” x 2” Bolt (12).
11 16. Attach the loop at the end of the Short Cable (58) to the Weight T ube (63) with a 5/16” x 1 1/2” Bolt (1 1) and a 5/16” Nylon Locknut (3). 16 3 63 58 11 17. Locate the Butterfly Cable (76). It is approximately 87 1/2“ long and it has a closed loop on both ends.
12 19. Remove the pre-attached Pulleys (15) from the Pulley Bracket (57). Wrap the Butterfly Cable (76) around a 3 1/2” Pulley (15) in the direction shown. Attach the Pulley to the upper part of the Pulley Bracket (57) with a 3/8” x 1 3/4” Bolt (68) and a 3/8” Nylon Jamnut (22).
13 24. Wrap the Long Cable (23) around a 3 1/2” Pulley (15) in the direction shown. Attach the 3 1/2” Pulley (15) and a Cable T rap (66) to the indicated hole in the welded bracket on the Base (4) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21).
14 27. Hook the closed loop on the end of the Long Cable (23) onto the 3/8” Eyebolt (35) that is mounted on the Leg Lever (29). T ighten the 5/16” Nylon Locknut (3) that is securing the other end of the Long Cable (23) to the Upright/Base. 27 23 29 35 3 28.
15 30. Press a 3/4” Round Inner Cap (34) into each end of the Pad T ube (28). Insert the Pad T ube (28) through the indicated hole in the Leg Lever (29). Slide a Foam Pad (30) onto each end of the Pad T ube. 30 34 30 34 30 28 29 31. Make sure that all parts have been properly tightened.
16 Cable Diagram (2) Long Cable (23) 2 1 6 7 8 5 3 4 Cable ID Chart 58, 130” 76, 87 1/2” 23, 233”.
Attaching the Lat Bar to the Pulley Station Attach the Lat Bar (54) to the Short Cable (58) with a Cable Clip (53). Adjusting the Arms for Butterfly or Press Exercises The Left Arm (47) and Right Arm (48) can be adjusted for either butterfly or press exercises by turning the Locking Pin (75).
18 Tightening the Cables Woven cable, the type of cable used on the home gym system, can stretch slightly when it is first used. If there is slack in the Cables before resistance is felt, the Cables should be tightened. T o tighten the Cables, insert the Weight Pin (26, not shown) between the third and the fourth Weight, counting from the top.
19 ICON of Canada Inc. 900 de l’Industrie St-Jérôme, Québec Canada, J7Y 4B8 PLACE ST AMP HERE Press Butterfly Pulley Leg Weight Arm Arm Station Lever Plates (lbs.
Ordering Replacement Parts T o order replacement parts, simply call our Customer Service Department toll-free at 1-888-936-4266, Monday through Friday , 8 a.m. until 6:30 p.m. EST (excluding holidays). T o help us assist you, please be prepared to give the following information: 1.
WESY74090 R0700A Note: Assembly is divided into four stages: 1) frame assembly; 2) arm assembly; 3) cable, pulley and seat assembly . The hardware for each assembly stage is packaged separately . Wait until you begin each stage to open that parts bag.
1/4" Flat W asher (10) 5/16" Flat W asher (8) 3/8" Flat W asher (9) 3/8" Nylon Locknut (21) 1/4" Nylon Locknut (2) 3/8" Nylon Jamnut (22) 3/8" Plain Nut (56) 1/4&quo.
1" Retaining Ring (69) 3/8" x 2" Bolt (12) 3/8" x 3" Bolt (72) 3/8" x 2 3/4" Bolt (71) 3/8" x 1 3/4" Bolt (68) 1/2" x 1/4" Spacer (44) 1/2" .
1" Round Inner Cap (49) 1" Round Cover Cap (70) 3/4" Round Inner Cap (34) 1 1/2" Square Outer Cap (27) 1" Square Inner Cap (65) 3/8" Eyebolt (35) 1 3/4" Square Inner.
8 1 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Part List—Model No. WESY74090 R0700A Key No. Qty .
53 54 31 31 69 70 69 70 47 74 74 48 52 10 2 52 10 2 16 21 22 56 76 59 59 56 22 76 17 77 77 32 77 73 73 77 77 68 15 12 78 22 22 12 1 22 3 61 1 55 15 40 58 44 44 15 44 44 8 9 9 9 9 57 68 22 15 22 60 15 .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Weider WESY74090 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Weider WESY74090 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Weider WESY74090 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Weider WESY74090 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Weider WESY74090, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Weider WESY74090.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Weider WESY74090. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Weider WESY74090 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
